Elkron Hp201 User manual

123456789012345678901234567890121234567890123456789012345678901212345678901234

2345678901234567890123456789012123456789012345678901234567890121234567890123

123456789012345678901234567890121234567890123456789012345678901212345678901234

2345678901234567890123456789012123456789012345678901234567890121234567890123

123456789012345678901234567890121234567890123456789012345678901212345678901234

HP201

HP202L

HP202LG

IS2033-AC

Installation Manual

External Siren

HP201 / HP202L / HP202LG2/8

• High mechanical resistance polycarbonate external box.

• Controls managed by microprocessor.

• BL and TC lock inputs with positive or negative reference.

• Possibility of programming sounder when lock signal is permanently down.

• Sounder counter: up to 5 over 24h or per activation sequence (TC transition).

• Alarm log for units with TC output (flasher blinking).

•System status report function: TC signal absence from control panel will cause continuous flash

blinking.

• Battery polarity inversion protection and power via control unit.

• Anti-opening and anti-removal protection.

• Initial lock function:theflasherwillblinkandthesirenwillnotsoundatfirstpower-up;connectlocksignal

(BL) and TC unit to set up siren for operation.

• Siren stops when the lock signal is down for longer than the programmed time. A new alarm cycle

will be generated if the lock signal goes down again (see "Siren programming").

• Acoustic pressure: 104 dB(A) - HP201 - HP202L models

102 dB(A) - HP202LG model

• Internal low battery saver function stops the flasher and privileges the siren.

1.00 General description

HP 201 NO OPTIONAL

HP 202 L YES OPTIONAL

HP 202 LG YES YES

MODEL FILAMENT

FLASHER

INTERNAL

PROTECTIVE

CAGE

(HP7410111)

CONTENTS

1.00 GENERAL DESCRIPTION .........................................................2

2.00 INSTALLATION...........................................................................3

3.00 TERMINAL BOARD ....................................................................4

4.00 SIREN PROGRAMMING ............................................................5

5.00 ALARM MANAGEMENT.............................................................5

6.00 TECHNICAL SPECIFICATIONS ................................................6

7.00 EXAMPLESOFCONNECTION...................................................7

HP201 / HP202L / HP202LG3/8

2.00 Installation

1) Disconnect siren module speaker wires. Remove the

speaker from the housing by loosening the fastening

screw and releasing the support (see figure 2).

2) Fasten the bottom of the siren to the wall using the bolts

and holes provided (see figure 1).

3) Insert the speaker module by fastening it to the support

and securing it with the specific screw.

4) Connect the terminal board (see section 3.00) and the

flasher. Connect the two anti-opening/anti-removal limit

switch wires to the siren module tamper terminals. Pro-

gram the siren (see section 4).

5) Remove the adhesive tape (A) holding the anti-opening/

anti-removallimitswitchandliftit.Thescrewonwhichthe

limitswitchrestsiscalibratedbythemanufacturertoclose

the contact when the cover is fitted.

hole for fastening

to wall

external cover

fastening screw

hole

wire hole

hole for fastening

to wall anti-removal

and anti-opening

limit switch

wire hole

internal cage

fastening screw

hole

internal cage

fastening screw

hole

external cover

fastening screw

hole

hole for fastening

to wall

12V 1.9Ah

battery

compartment

internal cage

fastening screw

hole

internal cage

fastening screw

hole

fig.1

fig.2

external cover

fastening screw

hole

hole for fastening

to wall

HP201 / HP202L / HP202LG4/8

TAMPER

Supporting terminals for connect anti-opening/

anti-removal limit switch wires leading to control

unit 24h input

TC1 FlasherlockTC1inputtoconnecttocontrolunitTC

referred to positive or negative (section 5.3)

BL1 Controlinputreferredtopositiveornegative(sec-

tion 5.3)

+Module power positive

-Power negative

+FLASH-

Flasher connection

SPEAKER

Speaker connection (short-circuit protected)

Either tighten or loosen the screw as required if the

switch is not closed because the supporting wall is

rough. Close the limit switch (B).

6) Fitthe12V1.9Ahbatteryinthehousingandconnectthe

fast-on: red wire to positive, black wire to negative. The

siren will not sound and the flasher will blink at the first

power-on.Theunitwillbesetforoperationafterapplying

the lock signal (BL) and the TC signal.

3.00 HP200terminalboard

fig. 3

TAMPER TC1 BL1

+FLASH-

SPEAKER

JP1 JP3JP4

JP5

HP201 / HP202L / HP202LG5/8

4.00 Sirenprogramming

4.1 Default programming

The siren can be programmed by either cutting or keeping a

number of jumpers. The default settings are all closed. The

siren can be programmed in the following way:

• maximum siren time = 3 minutes

• input reference = positive

• system status report = disabled

4.2 Sounder time programming

• This function is used to program the maximum delay after

which the siren will automatically stop if the lock signal

persists(thisfunctionisusefulisthewirewascut).Thesiren

willgenerateanewalarmcyclethenexttimethelocksignal

goes down.

JP3 CLOSED - JP4 CLOSED:sounder time = 3 min

JP3 CLOSED - JP4 OPEN: sounder time = 6 min

JP3 OPEN- JP4 CLOSED: sounder time = 9 min

JP3 OPEN- JP4 OPEN: sounder time = 30 min

4.3 BL1 and TC1 input reference

• This function is used to program the BL1 and TC1 input

referencestoeitherpositiveornegative.

JP5 CLOSED: POSITIVE REFERENCE

JP5OPEN: NEGATIVE REFERENCE

4.4 System status report

•Should this function be enabled, TC signal absence will

cause continuous flash blinking.

NOTE: when this function is enabled, alarm memory

function won’t be available.

JP1 CLOSED: FUNCTION DISABLED

JP1 OPEN: FUNCTION ENABLED

5.00 Alarmmanagement

•ThesirengeneratesanalarmonlywhenboththeTCsignalandthelocksignalaredown.

•The locksignalalone is sufficienttostop an alarminprogress.

•Afterlockingthealarm,theflasherwillcontinueblinkingtosignalthealarmpresenceuntiltheTC

signalisreceived(todeactivatethesystem).

• The alarm counter is reset either each time the system is switched off or after 24h from the

beginning of the first sounder operation. Only sounder cycles longer than 25s are considered

for this purpose.

• The sounder counter and the alarm memory are cut off by connecting TC and BL in parallel.

• Only alarms longer than 25 s are considered.

JP3 JP4

JP5

JP1

HP201 / HP202L / HP202LG6/8

6.00 Technicalspecifications

Nominalpower voltage ................................................................ 13.8V—

Minimum/maximum working voltage ........................................... 10.5V−15V—

NC positive input lock voltage...................................................... 5.5 V at nominal voltage

Stand-by consumption ................................................................ 9 mA

Alarm consumption ..................................................................... 1.3 A with flasher

HP202L/HP202LG maximum alarm consumption ...................... 0.7A

HP202L/HP202LGfilamentbulb.................................................. 12V 10W

Certified casing degree of protection (CEI 70.1 standards) ........ IP34

Casing degree of protection stated by manufacturer .................. IP43

IK* mechanical degree of resistance (CEI 70.3 standards) ........ IK08

Operating frequency.................................................................... min/max 1400 −1600 Hz

Acoustic pressure (models with internal cage) ........................... 102 dB(A) @3 m.

Acoustic pressure (models without internal cage) ...................... 104 dB(A) @ 3 m.

Allocablebattery .......................................................................... 12V1.9Ah;12V2Ah;12V2.1Ah

Anti-tamperfeature...................................................................... 1A @ 24V—

Working temperature range stated by manufacturer................... - 25°C /+ 70° C

Low battery threshold voltage...................................................... ≤10.8V

Dimensions:

HP201 model............................................................................... 212 x 240 x 78 (l x h x d)

HP202L,HP202LGmodel ........................................................... 212 x 270 x 78 (l x h x d)

* characteristics stated by manufacturer (but not certified)

HP201 / HP202L / HP202LG7/8

7.00 Examplesofconnection

TAMPER TC1 BL1

+FLASH-

SPEAKER

CONTROL UNIT

relè di allarme

alarm

relay

24h

ANTI OPENING

MICRO SWITCH

TAMPER TC1 BL1

+FLASH-

SPEAKER

CONTROL UNIT

relè di allarme

alarm

relay

24h

ANTI OPENING

MICRO SWITCH

In this configuration, the flasher only blinks at the

end of the sounder cycle and there are no sounder

counterfunctionandsystemstatusreport.

Example of connection with TC

Example of connection without TC

ELKRON S.p.A.

Via Carducci, 3 - 10092 Beinasco (TO)

TEL. +39(0)11.3986711 - FAX +39(0)11.3499434

www.elkron.it e-mail [email protected]

This manual suits for next models

Table of contents

Popular Security System manuals by other brands

EDS

EDS EDA-T Series installation manual

Europlex

Europlex SigNET 200 user guide

Axis

Axis 0936-001 20289045 installation guide

BV Security

BV Security DVR-CVI-16CH instructions

TALITOR(FAR EAST) CO.

TALITOR(FAR EAST) CO. CW1103 user guide

Climax

Climax Mobile Lite-R8 Slim Installer's guide

LTB

LTB Trakgard TRK instruction manual

DSC

DSC PowerSeries Neo 3G8080 installation manual

Dualtech

Dualtech TS100T Description and installation manual

Solar

Solar SMS001 user guide

Esse-ti

Esse-ti Helpy GSM quick guide

GENESIS INTERNATIONAL

GENESIS INTERNATIONAL SHERLOCK quick start guide

Force

Force 45176 quick start guide

Pulsar

Pulsar AWO 152 Assembly instruction

Tiiwee

Tiiwee Pager manual

Politec

Politec MANA MW INSTALLATION AND MOUNTING MANUAL

Schlage

Schlage keypad entry with built-in alarm user guide

ADEMCO

ADEMCO 4180 user manual

Elkron HP201 User manual

Popular Security System manuals by other brands