Elkron MP 110 M TG User manual

12345678901234567890123456789012123456789012345678901234567890121234
1
234567890123456789012345678901212345678901234567890123456789012123
4
1
234567890123456789012345678901212345678901234567890123456789012123
4
12345678901234567890123456789012123456789012345678901234567890121234
1234
1
23
4
1
23
4
1
23
4
1
23
4
1
23
4
1
23
4
1
23
4
1
23
4
1
23
4
1
23
4
1
23
4
1
23
4
1
23
4
1
23
4
1
23
4
1
23
4
1
23
4
1
23
4
1
23
4
1
23
4
1
23
4
1
23
4
1
23
4
1
23
4
1
23
4
1
23
4
1
23
4
1
23
4
1
23
4
1
23
4
1
23
4
1
23
4
1
23
4
1
23
4
1
23
4
1
23
4
1
23
4
1
23
4
1
23
4
1
23
4
1
23
4
1
23
4
1
23
4
1
23
4
1
23
4
1
23
4
1
23
4
1
23
4
1
23
4
1
23
4
1
23
4
1
23
4
1
23
4
1
23
4
1
23
4
1
23
4
1234
Alarm Unit
User Manual
IS0099-AE
MP 110
MP 110TG
MP 110 M
MP 110 MTG

(((ELKRON))) MP110 USER MANUAL (((ELKRON)))
MP110 USER MANUAL 39
Table of Contents
SYSTEM MANAGEMENT BY THE ALPHANUMERIC
DISPLAY KEYPAD KP100D...................................................3
1 Keypad description......................................................................... 3
2 Access codes ................................................................................. 4
3 System arming/dysarming .............................................................. 7
4 Sensor EXCLUDED/re-entry .......................................................... 9
5 Display of zone status .................................................................... 10
6 Clock setting................................................................................... 12
7 Systemtest ..................................................................................... 13
8 Telephone number programming.................................................... 13
9 Telephone line test ......................................................................... 14
10 Call result visualization .................................................................. 15
11 Listening to voice messages .......................................................... 15
12 Lock of alarm in progress................................................................ 16
13 Calling back ................................................................................... 16
14 List of messages on display............................................................ 17
SYSTEM MANAGEMENT BY KEYPAD
WITH SEGMENTED SCREEN KP100 ................................18
1 Keypad description ......................................................................... 18
2 Access codes ................................................................................. 19
3 System arming/dysarming.............................................................. 22
4 Sensor EXCLUDED/re-entry .......................................................... 24
5 Display of zone status .................................................................... 25
6 Clock setting ................................................................................... 27
7 Systemtest ..................................................................................... 28
8 Telephone number programming.................................................... 29
9 Telephone line test ......................................................................... 29
10 Call result visualization .................................................................. 30
11 Listening to voice messages .......................................................... 30
12 Lock of alarm in progress................................................................ 31
13 Calling back ................................................................................... 31
SYSTEM MANAGEMENT WITH
ELECTRONIC KEY DK2000M .............................................32
1 Commutator description.................................................................. 32
2 Electronic key programming ........................................................... 32
3 Arming/disarming ........................................................................... 36
2

(((ELKRON))) MP110 USER MANUAL (((ELKRON)))
MP110 USER MANUAL
Indicates the presence of the mains
voltage and the level of battery charge:
OFF = 220V~ mains absent
FIXED LIGHT = 220V~ Mains present
FLASHING = Low battery charge
Thesedisplaythe statusofthethree areas
into which the alarm system is divided:
ON = armed zone
OFF = disarmed zone
These Leds flash to indicate the
presence of events to be displayed.
Referto paragraph 5 “Display ofSystem
Status ”
Keysused to arm/disarm the system (see
par. “System Arming/Disarming). These
are also used to scroll the programming
menu.
Keys used to type in the secret code and
to select certain functions on the alarm
unit programming menus.
SYSTEM MANAGEMENT BY THE
ALPHANUMERIC DISPLAY KEYPAD
KP100D
1.Keypad Description
A flashing light indicates that alarms have occurred
A flashing light indicates that burglaries have occurred on one or
more parts of the system.
A flashing light indicates that there are protected zones (doors or
windows protected by contacts) that are still open.
A flashing light indicates that some sensors/contacts are disabled.
TOTAL
TEST
ZONE
TEL
EXIT
SIREN
123
A
12
45
7
3
6
9
F
0
8
C
S
O
E
**
3
2
13
KP100D
+-
3
Z1
Z2
Z3
Z4
Z5
Z6
Z7
Z8
A_
A_
B_
B_
SECTOR TYPE
PLACE WHERE THE DETECTOR IS INSTALLED
Fill in the following table together with the installator of your alarm system. For each of the
controlpanel inputyou are requestedto markdown the detectorto whichthe inputis associated
and the sector in which it is installed.
Z1 2 Intrusion Entry door
B_ 3 Intrusion Rest Room
Detector table
1
38

(((ELKRON))) MP110 USER MANUAL (((ELKRON)))
MP110 USER MANUAL
4. To disarm the system, insert the key and remove it when the leds go
OFF.
Recognition of Key with Masked System
• When the system is masked, all the commutator leds are OFF.In this
wayit is impossible to knowwhether thesystem isarmed and masked
or actually turned OFF.
• Theinsertion ofa keywithvalidcode causes all fourcommutatorleds
tolight up for 0.5s.Thisindicates thatthe keycodehas been correctly
readand is followed by the display of system mode for 3.5 seconds.
• Removalof thekey before this time has expired causes the systemto
return tothe masked mode;leavingthe keyinsertedenablesa change
insystem modelike theone thattook placewith thearming/disarming
procedure by electronic key.
• Whilethe commutators always mask system mode, the keypads only
perform masking if the unit is armed.When OFF, all data is visible as
if the system were unmasked.
Code Recognition with Masked System
• Withmaskedsystem,allkeypadledsareoff,exceptforthemainsled.
Inthis way it is not possible toknow whetherthe system is armed and
masked or it is really off.
• By entering a valid code the keypad being used visualizes the plant
status for one minute: within this period it is possible to operate.
• After1minute from theintroductionofthecode,thesystemismasked
again.
37
2.Access Codes
• The unit can be programmed so as to enable User 2 (e.g., service
personnel, custodian, porter , telemonitoring, private vigilance, etc)
to have his own secret access code which allows him to arm/disarm
the unit without performing other operations.
• The unit identifies up to a maximum of 8 different assigned codes and
as many users:
• After entering a correct code that is enabled, the unit’s buzzer beeps
twice,orit beepsonceatlengthtoindicateanerror. TheMasteruser’s
codeisalwaysenabled;theothercodesmustinsteadbeenabled (refer
to par. “Code Enabling”).
• If the engineer’s code is enabled, it remains enabled until the Master
user’s code is again entered to partially or totally arm the system, or
until the first arming by electronic key-
• Once armed, every re-entry/EXCLUDED display procedure triggers a
1-minute delay (that is reset each time the key is pressed). If a delay
time-out occurs, the procedure is exited automatically without saving
the changes made.
• The pressing of each key whileentering the secret code causes an
asterisk to be displayed.
FACTORY
CODE
CODE 1 - MASTER USER 111111
CODE 2 - USER 2 222222
CODE 3 - ENGINEER 333333
CODE 4 - TELEMONITORING 444444
CODE 5 - USER 5 555555
CODE 6 - USER 6 666666
CODE 7 - USER 7 777777
CODE 8 - USER 8 888888
Each user is assigned and “identification
number “ (from 1 to 8) that is to be typed in
before the code; this number allows the unit to
identify the user of the system.To be identified
by the system, the owner must type in the
number 1 followed by his personal code; any
other users will instead type in the number 2,
3, 4, 5, 6, 7 or 8, followed by his personal code
4

(((ELKRON))) MP110 USER MANUAL (((ELKRON)))
MP110 USER MANUAL
2.1 Changing of Personal Code
1. Type in the access code that is to be changed. The buzzer beeps
twiceto confirm that it is correct,otherwise it indicates an errorwith a
longbeep.
2. Press the
C
** key. The message «INSERT NEW CODE» appears
onthe display.
3. Enter the new code.The message «RE-INS NEW CODE» appears
on the LCD display.
4. Enter the new code a second time.
If the new code has been correctly entered, it is accepted and this is
confirmed when the buzzer beeps twice;otherwise, an error warning
is given and the procedure is exited.
Example of code change
- The Master user wishes to change the factory code 1-11111.
- Typein111111on the keypadand press the
C
** key. Themessage
“ENTER NEW CODE” appears on the display.
- Enterthe newcode, forexample,165744.Themessage“RE-ENTER
NEWCODE”appearsonthe LCDdisplay.Now re-type the numbers
165744.
- The buzzer beeps twice to confirm acceptance of the new code.
1. Enter the MASTER User code.
2. Press the
F
key and then the
C
** key.The message “ENABLE
CODE” appears on the display.
It is now possible to enable/disable the engineer’s code, the
telemonitoring code, the User2 codeand the keycode.These 4 codes
are associated with the 4 leds present on the keypad:
ENGINEER
TELEMONITORING
USER 2
KEY CODE (EK)
3. Press the key next to the led to enable/disable the corresponding
code
4. Press the EXIT
F
key to exit the procedure.
Note: the first number
of the code must be the
user’s identification
number:
1for the Master user
2for User 2
3fo r the engineer
4for telemonitoring
5 for User 5
6for User 6
7for User 7
8for User 8.
2.2 Enabling/Disabling of the User 2,
Engineer’s, Telemonitoring and Key Codes
The key code cannot be
changed: when enabled, it
allows use of the electronic
keysand of the commutators.
When disabled, it prevents
the operation of all the
commutators and of existing
keys(only system status will
be displayed by the
commutators’ leds).
KEY
CODE
The leds respectively indicate the
status of codes
Led ON = Code enabled
Led OFF = Code disabled
5
3. Arming/Disarming
Commutator leds 1 (zone 1), 3 (zone 2) and 4 (zone 3) indicate the
system’s current status:
ON = armed zones
OFF = disarmed zones
1. Insert the commutator key and leave it inserted.
2. If the key inserted controls only one of the three zones, the status of
thezonefor whichthekeyoperationisenabledchangesimmediately.
3. Ifthekeycontrolsmorethanonezone,thesystemcyclicallyindicates
the possible combinations that can be applied for a maximum of 4
times.
If the key controls two zones, the system displays the following
sequence:
If the key controls all three zones, the system offers the following
sequence:
Removal of the key with one of these combinations set causes
permanent arming of the selected mode and triggers the exit delay
procedure (when programmed).With the key permanently inserted,
at the end of the fourth cycle, the system exits the procedure and
remains in the previous mode.
ON = ZONE 1 ARMED
OFF = ZONE 1 DISARMED
ON = ZONE 2 ARMED
OFF = ZONE 2 DISARMED
ON = ZONE 3 ARMED
OFF = ZONE 3 DISARMED
11 ON - 3ON removal of key arms both zones
21 ON - 3 OFF removal of key arms zone 1
31 OFF - 3 ON removal of key arms zone 2
11ON 3 ON 4 ON removal of key arms all three zones
21 ON 3 OFF 4 OFF removal of key arms zone 1
31 OFF 3 ON 4 OFF removal of key arms zone 2
41 ON 3 ON 4 OFF removal of key arms zones 1 and 2
51 OFF 3 OFF 4 ON removal of key arms zone 3
61 ON 3 OFF 4 ON removal of key arms zones 1 and 3
71 OFF 3 ON 4 ON removal of key arms zones 2 and 3
36

(((ELKRON))) MP110 USER MANUAL (((ELKRON)))
MP110 USER MANUAL
2.4 Check of Stored Keys
1. Enter the MASTER USER code on th ekeypad and press keys
F
+
7
in sequence.
2. Pressthe
1
keyseveraltimes untilthe following message appears
on the display:
• keypad with alphanumeric display:“KEY CHECK”
• keypad with segmented display:“
C
” (flashing”)
3. Press the
7
key. Commutator led 2 flashes slowly to indicate
system standby for entry of the key to be checked.
4. After entering the key to be checked, if its code corresponds to the
storedcode,leds 1, 3and 4 ofall the deviceswillindicatethe controlled
zones. The number of the entered key appears on the segmented
displays,while the alphanumericdisplayindicates the message“KEY
NUMBER nn”, where “nn”corresponds to the number of the key that
isread.
If the key code entred does not correspond to the stored code, all
zone leds will flash quickly and the message “UNKNOWN KEY”
appearson thealphanumeric displays.Flashingwill continueuntil the
key is removed.
Press key Fto exit.
35
1. Enter the User 1 code.
2. Press the
F
key and then press the
C
** key twice; the message
“AUX CODE 05”appears on the display.
3. To choose another user code to be enabled/disabled (either 5, 6, 7 or
8), press key
1
or
2
.
4. The system zones controlled by the code being consideredare
displayed by leds 1, 2 and 3.
Led ON = zone controlled by code
Led OFF = zone not controlled by code
For example, if all 3 leds are ON, this means that the user under
consideration can arm or disarm the entire system; if only led 1 is lit,
it means that the user can manage only zone 1.
5. Tochange the combination displayed,press the
C
** key(associated
sector leds blink) and use keys
1
,
2
,
3
(corresponding to
zones S1, S2, S3) to associate or not associate the desired zones
with the user in question. The associated zone is indicated by the
flashing of the corresponding led; if the led is OFF, it means that the
correspondingzone isnot in operation.
6. Onceconfiguration of thecodeunder consideration iscompleted,press
the
C
** key. The leds of the associated zones will light up with a
fixed light..
7. To change the association of the zones, continue as indicated in item
3.
8. To terminatethe auxiliary codes enabling/disabling operations,and to
store the selections made, press the
C
** key twice and then press
the
EXIT
F
key to exit programming.
2.3 Enabling/Disabling of User Codes
5, 6, 7 and 8 and codes/sectors
association
associates zone 1
associates zone 2
associates zone 3
zone1
zone 2
zone 3
3
2
13
1
2
3
6

(((ELKRON))) MP110 USER MANUAL (((ELKRON)))
MP110 USER MANUAL
3.System Arming/Disarming
• For ARMINGofthesystem,enteravalidcodeandpressthe
TOTAL
key.
all sectors referred to the entered code will be armed. The leds
correspondingtothearmedsectorswillflashandthenturnon inafixed
mod
If an exit delay occurs, it is indicated by the buzzer with an intermittent
signal .
•ToDISARM the system, enter a valid code and press the
TOTAL
key.
Leds
13
,
2
and
3
areturnedOFF and the buzzer
beepstwice.
• To partially ARM the system, enter a valid code and press the key for
the zone or zones one wishes to arm.
1
toarmZone1-theled
13
flashesand lights upwithafixed
light after 4 seconds.
2
toarmZone2-theled
2
flashesandlightsupwitha fixed
light after 4 seconds.
3
toarmZone3 -led
3
flashesandlightsupwithafixedlight
after 4 seconds.
• ToDISARMthesystem,enteravalidcodeandpressthe
TOTAL
key.The
leds of the previously armed zones are turned OFF and the buzzer
beeps twice.
• Duringpartialarming,about5secondsareavailable (led flashing time)
within which it is possible to correct the type of arming; once this time
is up, the leds light up with a fixed light and the sectors are armed.
• After selecting the desired configuration for the zones, arming can be
confirmed by pressing the
A
key without waiting for the time
available for arming to expire.
3.1 Arming/Disarming
3.2 Partial Disarming
7
Ifthe operation wasnot successfullyperformed (for example,because
thekeywas not removedwhileled 4flashed quickly),all leds will flash
quicklytoindicatethattheoperation has failed andthattheprogramming
operation must be repeated. In this case, the message “PROGRAM
ERROR” appears on the alphanumeric display, while the symbol “-”
appears on the led display and all three zone leds flash.
8.Remove the key. Return to item 4 to program the other keys or press
key
F
to exit
2.2 Addition of a Key
1. Enter the MASTER USER code on the keypad and press keys
F
+
7
in sequence.
2. Press the
1
keyseveraltimesuntil the followingmessage appears
on the display:
• keypad with alphanumeric display:“KEY ADDITION”
• keypad with segmented display :“
a
” (flashing)
3. Press the
7
key. Commutator led 2 flashes slowly to indicate
system standby for entry of the additional key.
4. Proceed inthe order described in items 4, 5, 6,7 and8 of the previous
section to associate the desired sectors to the key.
2.3 Duplicationof aKeyCode
1. Enter MASTER code on keypad and press keys
F
+
7
in
sequence.
2. Press key
1
several times until the display shows the following
message:
keypadwithalphanumericdisplay:“READ KEY CODE”
keypad with segment display: “
L
” (flashing)
3. Presskey
7
.Led 2 of the commutator flashes slowly to show that
the system is waiting for the introduction of the key to be duplicated.
4. Introduce the key to be read. After approx. 2 seconds a double beep
willbe generated toconfirmthatthe codehas been read.The procedu-
re is terminated and the system has stored the key code. Press key
F
to exit.To make the desired keys operating, follow the procedu-
re “ Addition of a key” , para 2.2.
34

(((ELKRON))) MP110 USER MANUAL (((ELKRON)))
MP110 USER MANUAL
2.1 Storage of a New Key
1. Enter the MASTER USER code on the keypad and press keys
F
+
7
in sequence.
2. Press th
1
key several times until the following message appears
on the display:
• keypad with alphanumeric display:“KEY PROGRAM”
• keypad with segmented display:“-” (one flashing hyphen)
3. Press the
7
key. Commutator led 2 flashes slowly to indicate
system standby for entry of the first key.
4. Insert the commutator key.The system proposes key enabling on all
three zones with the lighting of leds 1, 3 and 4. If this is the desired
configuration, remove the key while led 2 flashes quickly.
5. Byleaving the keypermanently inserted, thevarious combinations of
zones with which the key can be associated are displayed with the
lighting of leds 1, 3 and 4, as shown in the table below:
6. When the desired combination has been set, remove the key ONLY
WHILE LED 2 FLASHES QUICKLY.
7. Re-insert the key. If the operation has been successfully
performed,the leds of the zones previouslyassociated with the key
will light up and led 2 flashes slowly while standing by for the
programming of any other keys.
slow
flashing
led 1, 3
and 4 ON
11 ON 3 ON 4 ON the key is associated with all 3 zones
21 ON 3 OFF 4 OFF the key is associated with zone1
31 OFF 3 ON 4 OFF the key is associated with zone 2
41 ON 3 ON 4 OFF the key is associated with zones 1and 2
51 OFF 3 OFF 4 ON the key is associated with zone 3
61 ON 3 OFF 4 ON the key is associated with zones 1and 3
71 OFF 3 ON 4 ON the key is associated with zones 2 and 3
33
3.6 Disarming with Antirobbery Code
Ifthesystemisequippedwithanintegratedtelephoneunitorotherremote
transmissionsystem,apanicalarmsignalcanbesentincaseofconstraint
to disarm the antirobbery system.
• The disarming procedure described in para 3.1 is carried out, but it is
necessaryto enter thesecret code increasing the lastdigit by oneunit.
• Example: code 123456 would become 123457; code 132459 would
become132450.
• Disarm the control unit; if within approx.30 sec the correct code is not
entered the control unit will send the panic alarm to all programmed
telephonenumbers.
3.7 Wrong Code
• In case of introduction of a wrong code for 4 consecutive times, the
system visualizes a tamper on the keypads and the readers. When
introducingawrongcodeforthefifthconsecutivetime,thesystemstarts
atamperalarm.
3.3 Arming with Reduced Code
• It is sufficient to enter the first 2 digits of the code followed by key
TOTAL
for a total arming, or
1
,
2
or
3
for a partial arming.
• Quick arming is possible only if the system is fully disarmed.
3.4 Commutating Lock with Open Zones
• If the commutating lock with open zones has been programmed, it will
notbe possible toarm –neither fromkeypad norby DK key– the sectors
to which the currently open zones are associated. If you try such an
armingfrom keypad, arelevant warning isprovided on thedisplay and
no arming will take place.
3.5 Open Zone Self-Bypassing
• If both commutating lock and self-bypassing have been programmed,
the zones left open are automatically bypassed when an arming from
keypador DKkey is carried out. If the arming is madefrom keypad,the
self-bypassingisproperly signalled on the display.The armingregularly
takes place and no alarm is generated.The self-bypassed zones are
reenteredautomatically at their re-closing (even with armed system).A
followingopening will therefore generate the alarm.
8

(((ELKRON))) MP110 USER MANUAL (((ELKRON)))
MP110 USER MANUAL
4.Sensor EXCLUDED/Re-entry
1. Enter the Master user code and press the
E
key.
2. The first sensor available for EXCLUDED is proposed.The message
“INSULATION Z nn” appears on the display (where nn refers to the
number of the sensor, see the sensor table to know to which zone it
corresponds).
3. Use the
1
key to forward scroll the list of sensors..
Use the
2
key to backward scroll the list of sensors.
Use the
TOTAL
key to return to the beginning of list.
4. To EXCLUDED the sensor under consideration, press
E
.
The message “ZONE nn INSULAT” appears on the keypad screen.
If all the sensors are EXCLUDED, the message “ALL ZONES
INSULAT” will appear on the LCD display.
5. Press
EXIT
F
to exit the programming function.
1. Enter the Master user code and press the
O
key.
2. Re-entry of the firstEXCLUDED sensoris proposed with the message
“SETTING ZONE nn” (where nn is the number of sensor, refer to the
sensor table to know to which zone it corresponds).
3. Use the
1
key to forward scroll the list of EXCLUDED sensors.
Use the
2
key to backward scroll the list of EXCLUDED sensors.
Use the
TOTAL
key to return to the beginning of the list.
4. To include the zone under examination, press
O
5. Themessage “ZONE nn SETTED”will appear on the keypadscreen.
To select the next zone, press the
1
or
2
key.The message
“ALL ZONES SETTED” will appear on the display if there are no
EXCLUDED zones.
6. Press EXIT
F
to exit the programming function.
4.1 Sensor EXCLUDED
4.2 Re-entry of Previously EXCLUDED Sensors
9
2. ElectronicKeyProgramming
SYSTEM MANAGEMENT WITH
ELECTRONIC KEY
DK2000M
1.Commutator Description
ON = alarms stored, low battery,
absence of mains, system
failures,tampering
SLOW FLASHING =
during key programming and to
signal open inputs. In case of
concomitance of stored alarms,
failure,etc. with open inputs, the
led flashing will be fast.
ON = ZONE 1 ARMED
OFF = ZONE 1 DISARMED
ON = ZONE 2 ARMED
OFF = ZONE 2 DISARMED
ON = ZONE 3 ARMED
OFF = ZONE 3 DISARMED
Once your system has been installed, if management by electronic key
is foreseen, the unit must acquire the keys that you intend to use.We
recommendperforming the first storage in the presence of the engineer.
Keys can be stored in three different ways:
-STORAGE OF A NEW KEY
For storing a key code in a new system or changing the code of all
keys in case one key is lost
-ADDING A KEY
For adding one or more keys to an existing system
KEYCODE DUPLICATION
For storing a key code in a second system by copying it from a
previously programmed key.With this function it is possible to check
oneor more systems with asingle key. Forexample,thehome system
and the office system will both recognize the same key (without
needing to use 2 different keys).
CHECK OF STORED KEYS
For checking previously programmed keys, by verifying correctness
of code, the key number and the zones controlled.
32

(((ELKRON))) MP110 USER MANUAL (((ELKRON)))
MP110 USER MANUAL
• The acknowledgement of a correct code (keypad entry, reading of a key,
or mechanical key arming) immediately stops all alarms thay may be in
progressexception made for the telephone calls.
• To lock the communicator (burglary events),it isnecessaryto disarm the
systemfrom keypad,commutator,ormechanical key.Ifthe communicator
has already started a transmission, the current call is completed and the
following voice calls are cancelled.
12. Lock of Alarm in Progress
Thefunctionallowsthecontrolunitreceivingatelephonetelemanagement
callfromtheengineer (FASTLINK+MODEM)tocallbackimmediatelyafter
checking the safety codes.
NOTE:thetransponderfunctionshallbeenabled
The function is factory disabled and can be enabled only by the MASTER
USER with two different modes:
- mode A thecontrol unitcallsback thefirstMODEMtype numberamong
theprogrammednumbers
- mode B the control unit calls back a specific telephone number sent by
FASTLINK
Thefollowing procedure is accessed:
1. Enter MASTER USER code
2. Press F+ TEL
9+
ZONE
3
in sequence
3. The display will visualize : c 0 (default value)
4. By means of key
1
it is possible to select:
c A (call back - mode A)
c B (call back - mode B)
5. Press key
F
to confirm and exit from programming
13. Calling Back
31
5. Display of Zone Status
• The flashing of the led indicates that one or more alarms are
stored.Press the
A
key for a display of the stored alarms;
• The message “ALARM ZONE nn”’appears on the display (where nn
isthe numberof sensor,refer to the sensor tableto know towhich zone
itcorresponds).
• For a display in sequence of the other zones (inputs), press the
1
key consecutively. Pressing the
TOTAL
key during display will recall the
the first zone on the list. At the end of the list, the message “END OF
DATA” is displayed.
• Press the
A
key.When there are no stored alarms the message
“NO DATA” is displayed.
• The flashing of the led indicates that one or more intruders
are stored.Press the
S
key to display these.
• Themessage ”TAMPER ZONE nn” appears on the display(where nn
is the number of the sensor, refer to the sensor table to know which
zone it corresponds to).
• The flashing of the led indicates that there are one or more
open zones. Press the
O
key to display these.
• The message “ZONE OPEN nn” will appear on the display (where nn
is the number of the sensor, refer to the sensor table to know which
zone it corresponds to).
5.1 Display of Stored Alarms
5.2 Display of Stored Intruders
5.3 Display of Open Zones
10

(((ELKRON))) MP110 USER MANUAL (((ELKRON)))
MP110 USER MANUAL
• Press key
C
** followed by key
8
.
• The display shows date and time : “dd-mm-yy hh-mm” replacing the
factoryset message “((EKLRON) MP 110)”.
• To re-establish the factory set message replacing the date/time, press
C
** +
O
in sequence.
• The flashing of the led indicates one or more EXCLUDED
zones.
• Todisplaythe EXCLUDED sensors, type inthe USER1 code and press
the
O
key.
• The first EXCLUDED zone is indicated by the message “SETTING
ZONE nn” (where nn is the number of the sensor, refer to the sensor
table to know to which zone it corresponds).
• Use the
1
key to forward scroll the EXCLUDED sensors.
Use the
2
key to backward scroll the EXCLUDED sensors.
Use the
TOTAL
key to return to the beginning of the list.
• Press EXIT
F
to exit the programming function.
See par. 6.
toset
thedate/time
5.4 Date/Time Visualization
5.5 Display of EXCLUDED Sensors
11
10. CallResultsVisualization
1. Further to an alarm, this procedure allows to verify which telephone
numbershave been called and which have properly answered.
2. Enter MASTER code + F+ 9+ A.
3. Thecalled numbersare visualized in sequence approx. every 1 second
withthefollowingmode:ontheleftdigit the telephone number isvisualized,
onthe right digit the samenumber isvisualized in case of positive ended
message or with a horizontal dash in case of no answer.
4. Incase of information lack the display willvisualize the symbol “- -“ (two
dashes)
5. If you want to cancel the information, press key E.
6. To exit from procedure press key Ftwice.
11. Listening toVoice Messages
Listening takes place by means of the loudspeaker connected to the
voice board in the control unit
1. Enter the MASTER USER code.
2. Press the keys
F
+
TEL
9
+
5
.
3. Press key
5
to start the reproduction of all recorded messages, at
the end of the messages, you go back to the communicator menu.
4. If you want to listen to a message in particular, use keys
12
to
selectthe desired message and to start listeningbymeans of key
5
.
5. At the end of the reproduction, a following message can be selected.
Press
EXIT
F
to exit from listening procedure.
Example of call on telephone no. 5 that
hasproperly answered
Example of call on telephone no. 5 with
no answer
30

(((ELKRON))) MP110 USER MANUAL (((ELKRON)))
MP110 USER MANUAL
1. Enter MASTER code
2. Press keys EXIT
F
+
TEL
9
+
O
in sequence
3. The display will visualize the two flashing digits corresponding to the
firstvoicenumber;by keys
1
and
2
itispossibleto go to other
numberstobeprogrammed.
4. Presskey
O
correspondingtothetelephonenumber to be
programmed. The digits will remain on in a fixed mode.
5. Press key
S
: approx. every 1 s. the digits of the first
telephone number are visualized (one digit at a time). For every
visualizeddigit, the buzzerwill beep twice(in case ofno programmed
digit, the display will visualize “- - “. Once completed the number
visualization, you go back to point 3).
6. Presskey
E
toaccesstheintroductionofanewnumber(thedisplay
willshow“n”flashing”).Bymeansofthenumerickeys,enterthedesired
number.Tointroduceapause,enterC**followedbyonenumerickey
corresponding to the desired length of the pause (see side table).
7. Presskey
O
toconfirmandsavetheenterednumber.The
buzzer beeps twice to confirm operation and you go back to point 3.
8. Tocancelapreviouslyprogrammedtelephonenumberproceedup to
point 4 and then press key Efollowed by key
O
. The
telephonenumber iscancelled.
9. Press key EXIT
F
twice to exit from programming.
8.Telephone Number Programming
AVAILABLE PAUSES
C
**
, 1 = 1sec. ---->
C
**
, 5 = 5sec. ---->
C
**
, 9 = 9sec. ---->
9.Telephone LineTest
1. Enter MASTER code + F+ 9+
3
.
2. The keypad display will visualize symbol (on in fixed mode).
3. Press key
3
to start procedure.
The keypad display will visualize the following message:
(flashing).
4. At the end of the test, you go back to the main menu of the
communicatorparameters.
5. Press key EXIT
F
to exit.
29
6.Clock Setting
1- Enter MASTER code
2- Press in sequence Fand 8
3- The display will show “Prog. Time hh:mm”
4- Enter a value between 00 and 23 ( 2 digits required)
5- Enter a value between 00 and 59 ( 2 digits required)
• To confirm and store the entered time, press key F
• Beforestoringtheenteredtime,theentereddataarecontrolled.Incase
of inconsistency, an error beep is generated and you go back to point
3.Incaseof correct data, thenewtime is stored andthepositive result
oftheoperationisconfirmedbyanOKbeep.Whenquittingbytimeout,
the modification is not saved.
6.2 Date Modification
1- Enter MASTER code
2- Press in sequence Fand
5
3- The display will show “PRG DATE dd-mm-yy”
4- Bymeansofthe numerickeysenterthedateofthedesiredday(2digits
from 0 to 31).
5- Enteravaluefrom01to12(2digits)correspondingtothedesiredmonth.
6- Enteravaluefrom00to99(2digits),correspondingtothedesiredyear.
7- To confirm and store the entered date, press key F.
• The system carries out no control on the consistency of the entered
data; the operator shall therefore ascertain that the programmed day/
monthdataarecorrectbeforeconfirming.Whenquittingbytimeout,the
modification is not saved.
6.1 Hours/Minutes Modification
12

(((ELKRON))) MP110 USER MANUAL (((ELKRON)))
MP110 USER MANUAL
7. System Test
- Enter the access MASTER code.
- Press key
F
+ key
3
. All leds turn on. A 30s delay is armed
during which the system test is carried out.
- By pressing kei SIREN
1
, you access the alarm siren test and all allarm
actuator can be tested for 5s. To stop the alarm, press SIREN
1
again
or
EXIT
F
.
- Bypressing key ZONE
3
,youaccessthe input testprocedure,anyalarm
memory is turned off and a 10min delay is armed , after which you
automatically quit the test.
- Afterarmingthetestprocedure,thesensoreffectivenesscanbetested
by means of the WALK-TEST (you walk in front of the sensor). The
displaywillshowthenumberofthesensorinalarm,whilethebuzzerwill
generate a sound for 5 seconds.
- Ifyou walk in front of a “disabled” sensor, itis visualizedon thedisplay
butthebuzzerwillgeneratenosound.Thismeansthatadisabledinput
is only stored but generates no alarm.
- By pressing key EXIT
F
from procedure, then it is possible to see the
testedinputsresultedeffectivebymeansofthestoredalarmvisualiza-
tion procedure (key
A
+ key
1
) .
NOTE:
• The test phase is signalled on all keypads and all commutators of the
plantbymeansofappropriate indications on thedisplaysandtheslow
flashing of the 3 sector leds.
8.Telephone Number Programming
1. Enter MASTER USER access code
2. Press key EXIT
F
+
TEL
9
+
O
in sequence.
3. The display visualizes the first programmed telephone number: “Tn:
nnnn——n”(if thereis no programmedtelephonenumber,therewill be
emptycharacters).
4. To go to other available numbers, if any, use keys
1
and
2
.
13
• The display will show the characters “ ” flashing to show the
introduction of the year.
• Enter a value from 00 to 99 (2 digits).
• To confirm and store the entered date, press key
F
.
• The system carries out no control on the consistency of the entered
data; the operator shall therefore ascertain that the programmed day/
month data are correct before confirming. In case of correct data, the
newdate is storedand the positiveresult ofthe operation isconfirmed
byanOKbeep.Whenquittingbytimeout,themodificationisnotsaved
7. System Test
•Enter the access MASTER code.
• Press key
F
+ key
3
. All leds turn on while any alarm memory
turns off. A 30s delay is armed during which the system test is carried
out.
• By pressing key
SIREN
1
, you access the alarm siren test and all alarm
actuators can be tested for 5s. To stop the alarm , press
SIREN
1
again
or
EXIT
F
.
• Bypressingkey
ZONE
3
,youaccessthe input testprocedure,anyalarm
memory is turned off and a 10min delay is armed , after which you
automatically quit the test.
• Afterarmingthetestprocedure,thesensoreffectivenesscanbetested
by means of the WALK-TEST (you walk in front of the sensor). The
displaywillshowthenumberofthesensorinalarm,whilethebuzzerwill
generate a sound for 3 seconds.
• Ifyou walk in front of a “disabled” sensor, itis visualizedon thedisplay
butthebuzzerwillgeneratenosound.Thismeansthatadisabledinput
is only stored but generates no alarm.
• By pressing key
EXIT
F
from procedure, then it is possible to see the
testedinputsresultedeffectivebymeansofthestoredalarmvisualiza-
tion procedure (key
A
+key
1
) .
28

(((ELKRON))) MP110 USER MANUAL (((ELKRON)))
MP110 USER MANUAL
6.Clock Setting
6.1 Hours/MinutesModification
1. Enter MASTER code.
2. Pressin sequence
F
and
8
;the display will showthecharacters
“” flashing to show the introduction of the hours.
• Enter a value between 00 and 23 ( 2 digits required). The display will
show the entered data in a fixed mode.
• The display will show the characters “ ” flashing to show the
introduction of the minutes.
• Enter a value between 00 and 59 ( 2 digits required).
• To confirm and store the entered time, press key
F
.
• Beforestoringtheenteredtime,theentereddataarecontrolled.Incase
ofinconsistency,anerrorbeepisgenerated,youquitwithoutmodifying
the data and the display will show the characters “ ” flashing to
show a new data introduction. In case of correct data, the new time is
stored and the positive result of the operation is confirmed by an OK
beep. When quitting by timeout, the modification is not saved.
6.2 Date Modification
1. Enter MASTER code.
2. Press in sequence
F
and
5
.
• Thedisplaywillshowthecharacters “ ”flashingtoinvitetheuser
to enter the day of the month.
• Bymeansofthe numerickeysenterthedateofthedesiredday(2digits
from 0 to 31).The display will show the number of the chosen day in a
fixedmode.
• The display will show the characters “ ” flashing to show the
introduction of the month.
• Enter a value from 01 to 12 (2 digits).
• Use the
1
key for forwas EXCLUDED sensor selection
Use the
2
key for backward EXCLUDED sensor selection
Use the
2
to return to the beginning of list
• Press
F
to exit programming
27
1. Enter MASTER code + F+ 9+
3
.
2. The keypad display will visualize the following message:
TESTCALL.
3. Press key
3
to start procedure.
The keypad display will visualize the following message:
TEST IN PROGRESS…..
4. At the end of the test, you exit automatically from the procedure.
9. Telephone LineTest
5. Confirm the choice of the telephone number by key
O
:
insteadof thenumber,thedisplaywill showsome dashes “-------------”
6. Bymeans of the numeric keys,enter the desired number.Every dash
“-“ is replaced by the desired digit.To introduce a pause, press
C
**
followed by a number key corresponding to the length of the desired
pause: the chosen pause will be visualized on the dash following the
lastentered digit. It is possible to cancela digit by pressing key E.
7. Press key
O
to confirm and savethe numberentered.The
buzzer generates a double beep to confirm the operation and you go
back to point 3.
8. If you want to program or cancel other numbers, use keys
1
and
2
to go to the desired number and proceed as described from
point5 onwards.
9. To cancel a previously programmed telephone number, press key
O
twice, when the telephone number to be cancelled is
visualized,thebuzzer generates adouble beep toconfirmcancellation.
10.Press key EXIT
F
to exit.
AVAILABLE PAUSES
C
**
, 1 = 1sec. ----> A
C
**
, 5 = 5sec. ----> B
C
**
, 9 = 9sec. ----> C
14

(((ELKRON))) MP110 USER MANUAL (((ELKRON)))
MP110 USER MANUAL
10. Call ResultVisualization
1. Further to an alarm, this procedure allows to verify which telephone
numbershave been called and which of them have properlyanswered.
2. Enter MASTER code + F+ 9+ A
3. The following message is visualized:
“ #:nnnnnn*:nnnnnn ” wheren=thecorresponding telephone number.
The first group of numbers (left) identifies the called numbers, the right
group thenumbers thathave properly answered.
In the following example, all numbers have been called and all of them
haveproperlyanswered: #:123456*:123456.
In the following example numbers 2,4,5,6 have been called by only
numbers2,5,and6haveproperlyanswered:#:-2-456*:2—56.
4. In case of information lack the displays will visualize the following
messages:#:________*:_________
5. To cancel information press key E.
6. To exit from procedure, press key EXIT
F
twice.
11. Listening toVoice Messages
• Listening takes place by means of the loudspeaker connected to the
voice board in the control unit
1. Enter the MASTER USER access code
2. Press keys
F
+
TEL
9
+
5
.
3. Press the
5
key to begin to reproduce the messages recorded, the
systemreturns to thecommunicator menu after all messageshave been
heard.
4. If one wishes to listen to a particular message, use the
12
keysto selectthe desiredmessage and startreproducing with the
5
.
key
5. After messages have been played reproduced, it is possible to select
thenext message. Press
EXIT
F
to exitthe messageplay backprocedure
andreturn to the communicator menu.
15
- Press the
C
** key, followed by
8
key .
- The display visualizes the following information in sequence approx.
every 1 second:
• flashing:‘hours’ from 00 to 12.
•flashing:‘minutes’from 00 a 59.
• exitsfrom procedure.
5.4 Time Visualization
5.6 Display of EXCLUDED Sensors
• One or more open zones are indicated by the flashing of the
led.To display these, press the
O
key.
• The number “nn” is displayed (where nn is the number of the sensor,
refer to the sensor table to know to which zone it correspsonds)
5.3 Display of Open Zones
• One or more EXCLUDED sensors are indicated by the flashing of the
led.
• Todisplaythe EXCLUDED sensors, type inthe USER1 code and press
the
O
key.
• ThefirstEXCLUDEDzone is displayedwith“nn” (where nnisthe number
of the sensor, refer to the sensor table to know to which zone it
corresponds)
- Press the
C
** key, followed by
5
key .
- The display visualizes the following information in sequence approx.
every 1 second:
•nn flashing, where nn = day of the month.
•nn where nn = month from 1 to 12.
•nn flashing, where nn = year from 00 to 99 (00=2000,
01=2001,etc.)
• exitsfrom procedure.
5.5 Date Visualization
26

(((ELKRON))) MP110 USER MANUAL (((ELKRON)))
MP110 USER MANUAL
5. Display of Zones Status
• One or more stored alarms are indicated by the flashing of the
.led Stored alarms are displayed by pressing the
A
key;
• Thenumber“nn”is displayed,(where nn is the sensor number,referto
the sensor table to know to which zone it corresponds)
• For a display in sequence of the other zones, press the
1
key
consecutively. If the
TOTAL
key is pressed during display, the first zone
on the list is shown again. At the end of the list, the symbol “- -” (two
hyphens) appears on the display.
• If the
A
key is pressed when there are no stored alarms, the
message “- -”(two hyphens) will appear on the display.
• One or more stored tamperings are indicated by the flashing of the
led.To display these, press the
S
key.
• The display will indicate the number: “nn” (where nn is the number
corresponding to the type of tampering that has occurred: see table
below)
5.1 Display of Stored Alarms
5.2 Display of Stored Tamperings
CONTROLUNITOPENINGTAMPER
FALSE CODE
T/ACONTROL UNITINPUT
WIRE INPUT t/A EXP.1
WIRE INPUTt/A EXP.2
FALSE KEY
SERIAL LINE SABOTING
WIRE INPUT t/A EXP.3
WIRE INPUT t/A EXP.4
EXP.1 OPENING TAMPER
EXP.2 OPENING TAMPER
EXP.3 OPENING TAMPER
EXP.4 OPENING TAMPER
TELEPHONE LINE FAILURE
25
• The acknowledgement of a correct code (keypad entry, reading of a key,
or mechanical key arming) immediately stops all alarms thay may be in
progressexception made for the telephone calls.
• To lock the communicator (burglary events),it isnecessaryto disarm the
systemfrom keypad,commutator,ormechanical key.Ifthe communicator
has already started a transmission, the current call is completed and the
following voice calls are cancelled.
12. Lock of Alarm in Progress
Thefunctionallowsthecontrolunitreceivingatelephonetelemanagement
callfromtheengineer (FASTLINK+MODEM)tocallbackimmediatelyafter
checking the safety codes.
NOTE:thetransponderfunctionshallbeenabled
The function is factory disabled and can be enabled only by the MASTER
USER with two different modes:
- mode A thecontrol unitcallsback thefirstMODEMtype numberamong
theprogrammednumbers
- mode B the control unit calls back a specific telephone number sent by
FASTLINK
Thefollowing procedure is accessed:
1. Enter MASTER USER code
2. Press F+ TEL
9+
ZONE
3
in sequence
3. The display will visualize : call back - 0 - (default value)
4. By means of key
1
it is possible to select:
call back - A - (mode A)
call back - B - (mode B)
5. Press key
F
to confirm and exit from programming
13. Calling Back
16

(((ELKRON))) MP110 USER MANUAL (((ELKRON)))
MP110 USER MANUAL
14. List of Messages on Display
MESSAGE: NOTES:
‘No PWR C.U. ZONES’ Short circuit or no power to inputs.
‘No PWR OUTPUTS‘ Short circuit or no power to sirens.
‘No PWR SERIAL‘ Short circuit or no serial power to peripherals.
‘LOWBATTERY’ Low,exhausted, no battery.
‘NO MAIN CONTROL PANEL’ No mains in control unit.
‘C.U.PWR SUPPLY’ Low power to control unit sensors.
(ccc)=Codice di accesso usato per operare (ove compare).
‘No PWR C.U. ZONES’ Input power failure.
‘No PWR OUTPUTS ‘ Siren power failure.
‘No PWRSERIAL ‘ Serial peripheral power failure.
“OK BATTERY ‘ Recharged battery.
‘OKMAIN’ Mains return to control unit.
‘—On/Off— unn’ Status shift (On/Off).
‘ON FROM REMOTE ‘ Remote arming (via FASTLINK).
‘START TEST unn’ Plant test start.
‘ENDTEST unn’ Plant test end.
‘START TELEG. unn” Telemanagement start (FASTLINK).
‘ENDTELEG.unn’ Telemanagement end (FASTLINK).
‘ALARM ZONE xx’ Alarm message –zone xx.
‘TAMPER ZONE xx’ Tamper message – zone xx ( For double bil inputs).
‘Z24 CONTROL PAN’ Control unit self-protection.
‘FALSE USER CODE’ Alarm due to false code entered from keypad.
‘FALSEKEY CODE’ Alarm due to false key code.
‘TAMPER KEYPAD x’ Keypad x self-protection.
‘ BUS READER x’ Tamper of commutator x serial line.
‘ BUS KEYPAD x’ Tamper of keypad x serial line.
‘ccc INSULAT. Z.nn’ Zone xx bypassing message carried out by user ccc
‘ccc SETTED Z.xx’ Zone xx reentry message carried out by user ccc
17
4.Sensor EXCLUDED/Re-entry
1. Enter the Master USER code and press the
E
key.
2. The first sensor available for EXCLUDED is shown. The display
indicates “nn”(where nn is the number of sensor, refer to the sensor
table to know to which zone it corresponds).
3. Use the
1
key for forwardEXCLUDED sensor selection
Use the
2
key for backward EXCLUDED sensor selection
Use the
TOTAL
key to return to the beginning of list
4. To EXCLUDED the sensor under consideration, press
E
.
The sensor number will flash on the keypad screen.
If all sensors are EXCLUDED, “--”(two hyphens) will appear on the
display.
5. Press
EXIT
F
to exit programming.
1. Enter the Master USER code and press the
O
key.
2. Re-entry of the first EXCLUDEDsensor will be proposed.Thedisplay
indicates “nn” (where nn is the number of the EXCLUDED sensor,
refer to the sensor table to know the zone to which it corresponds).
3. Use the
1
key for forward EXCLUDED sensor selection
Use the
2
key for backward EXCLUDED sensor selection
Use the
TOTAL
key to return to the begiinning of list
4. To re-enter the zone under consideration, press
O
5. The number of the sensor flashes on the keypad screenTo select the
next zone, press the
1
or
2
key. If there are no EXCLUDED
zones, the symbol“- -” (two hyphens) appears on the display.
6. Press EXIT
F
to exit programming
4.1 Sensor EXCLUDED
4.2 Re-entry of Previously EXCLUDED Sensors
24

(((ELKRON))) MP110 USER MANUAL (((ELKRON)))
MP110 USER MANUAL
3.6 Disarming with Antirobbery Code
Ifthesystemisequippedwithanintegratedtelephoneunitorotherremote
transmissionsystem,apanicalarmsignalcanbesentincaseofconstraint
to disarm the antirobbery system.
• The disarming procedure described in para 3.1 is carried out, but it is
necessaryto enter thesecret code increasing the lastdigit by oneunit.
• Example: code 123456 would become 123457; code 132459 would
become132450.
• Disarm the control unit; if within approx.30 sec the correct code is not
entered the control unit will send the panic alarm to all programmed
telephonenumbers.
3.7 Wrong Code
• In case of introduction of a wrong code for 4 consecutive times, the
system visualizes a tamper on the keypads and the readers. When
introducingawrongcodeforthefifthconsecutivetime,thesystemstarts
atamperalarm.
3.3 Arming with Reduced Code
• It is sufficient to enter the first 2 digits of the code followed by key
TOTAL
for a total arming, or
1
,
2
or
3
for a partial arming.
• Quick arming is possible only if the system is fully disarmed.
3.4 Commutating Lock with Open Zones
• If the commutating lock with open zones has been programmed, it will
notbe possible toarm –neither fromkeypad norby DK key– the sectors
to which the currently open zones are associated. If you try such an
armingfrom keypad, arelevant warning isprovided on thedisplay and
no arming will take place.
3.5 Open Zone Self-Bypassing
• If both commutating lock and self-bypassing have been programmed,
the zones left open are automatically bypassed when an arming from
keypador DKkey is carried out. If the arming is madefrom keypad,the
self-bypassingisproperly signalled on the display.The armingregularly
takes place and no alarm is generated.The self-bypassed zones are
reenteredautomatically at their re-closing (even with armed system).A
followingopening will therefore generate the alarm.
23
Indicates the presence of the mains
voltage and the level of battery charge:
OFF = 220V~ mains absent
FIXED LIGHT = 220V~ mains present
FLASHING = Insufficient battery charge
These display the status of the 3 zones
into which the alarm system is divided:
ON = armed zone
OFF = disarmed zone
TheseLeds flash to indicatethe presence
of events to be displayed, see paragraph
5 “Display of System Status”
Keysused to arm/disarm the system (see
par. “System Arming/Disarming”). These
are also used to scroll the programming
menu.
Keys used to type the secret code and to
select certain functions on the alarm unit
programming menu.
SYSTEM MANAGEMENT BY KEYPAD
WITH SEGMENTED SCREEN
KP100
1.Keypad Description
A flashing light indicates that alarms have occurred.
A flashing light indicates that burglaries have occurred on one or
more parts of the system.
A flashing light indicates that there are some protected zones (doors
or windows protected by contacts) that are still open.
A flashing light indicates that some sensors/contacts are disabled.
TOTAL
ZONE
TEL
EXIT
SIREN
123
A
12
45
7
3
6
9
F 0
8
C
S
O
E
**
3
2
13
KP100
+-
18

(((ELKRON))) MP110 USER MANUAL (((ELKRON)))
MP110 USER MANUAL
2.Access Codes
• The unit can be programmed so as to enable User 2 (e.g., service
personnel, custodian, porter , telemonitoring, private vigilance, etc)
to have his own secret access code which allows him to arm/disarm
the unit without performing other operations.
• The unit identifies up to a maximum of 8 different assigned codes and
as many users:
• After entering a correct code that is enabled, the unit’s buzzer beeps
twice,orit beepsonceatlengthtoindicateanerror. TheMasteruser’s
codeisalwaysenabled;theothercodesmustinsteadbeenabled (refer
to par. “Code Enabling”).
• If the engineer’s code is enabled, it remains enabled until the Master
user’s code is again entered to partially or totally arm the system, or
until the first arming by electronic key-
• Oncearmed,everyre-entry/EXCLUDED display proceduretriggers a
1-minute delay (that is reset each time the key is pressed). If a delay
time-out occurs, the procedure is exited automatically without saving
the changes made.
• Each time the key is pressed on the KP100 keypad (segmented
display),whileentering the secretcode,a segment ofthedisplay lights
up to display the digits (entered) as they are typed in.
FACTORY
CODE
CODE 1 - MASTER USER 111111
CODE 2 - USER 2 222222
CODE 3 - ENGINEER 333333
CODE 4 - TELEMONITORING 444444
CODE 5 - USER 5 555555
CODE 6 - USER 6 666666
CODE 7 - USER 7 777777
CODE 8 - USER 8 888888
Each user is assigned and “identification
number “ (from 1 to 8) that is to be typed
in before the code; this number allows
the unit to identify the user of the system.
To be identified by the system, the owner
must type in the number 1 followed by
his personal code; any other users will
instead type in the number 2, 3, 4, 5, 6,
7 or 8, followed by his personal code
19
3.System Arming/Disarming
• For ARMING of the system, enter a valid code associated to the 3
sectors and press the
TOTAL
key.
Leds
13
,
2
and
3
flash, and after 4 seconds they
light up with a fixed light.
Ifthereisananexitdelay, it is indicated bytheintermittentsoundofthe
buzzer.
• To DISARM the system, enter a valid code and press the
TOTAL
key.
Leds
13
,
2
and
3
correspondingtoactivesectors
go OFF and thebuzzer beeps twice.
• To partially ARM the system, enter a valid code and press the key for
the zone or zones ne wishes to arm.
1
toarmZone1 -theLed
13
flashesandlightsupwithafixed
light after 4 seconds
2
to arm Zone 2 - the Led
2
flashes and lights up with a
fixed light after 4 seconds
3
toarmZone3-theLed
3
flashesandlightsupwithafixed
light after 4 seconds
• ToDISARMthesystem,enteravalidcodeandpressthe
TOTAL
key.The
leds inthepreviouslyarmedzonesgoOFFandthebuzzerbeepstwice.
• Duringpartialarming,about5secondsareavailable(ledflashes) within
which it is possible to correct the type of arming; once this time is up,
the leds light up with a fixed light and the sectors are armed.
• After selecting the desired configuration for the zones, arming is
confirmed by pressing the
A
key without waiting for the time
available for arming to expire.
3.1 Away Arming/Disarming
3.2 Partial Arming/Disarming
22

(((ELKRON))) MP110 USER MANUAL (((ELKRON)))
MP110 USER MANUAL
1. Enter the MASTER user code.
2. Press the EXIT
F
key and then press the
C
** key twice.The number
5 appears on the display (user 5 code).
3. Press key
1
or
2
to select another code to be enabled/
disabled: the selected code will appear on the display.
4. The zones controlled by the code under consideration are indicated
by leds 1, 2 and 3.
Led ON = zone controlled by the code under consideration
Led OFF = zone not controlled by the code under consideration
5. To change the association displayed, press the
C
** key (the
associated sectors led blink) and use keys
1
,
2
,
3
(corresponding to zones S1, S2, S3) to combine (associate) or not
combine (associate) the desired zones to (for) the user in question.
Theassociated zoneis indicated by the flashing of thecorresponding
led; if the led is OFF, it means that the corresponding zone is not in
operation(for the code under consideration).
6. Once configuration of the thecode under consideration is completed,
press the
C
** key the blinking led will lit up fixed.To change the
association of the zones of a different code, proceed as indicated in
step 3.
7. Press
C
** again if one wishes to terminate the operation and store
theselections made.
Press the EXIT
F
key to exit.
2.3 Enabling/Disabling of User Codes
5, 6, 7 and 8 and codes/sectors
association
associates zone 1
associates zone 2
associates zone 3
zone 1
zone 2
zone 3
3
2
13
1
2
3
21
2.1 Changing Personal Code
1. Type in the access code that is to be changed. The buzzer beeps
twiceto confirm that it is correct,otherwise it indicates an errorwith a
long beep.
2. Press the
C
** key. The character , lit with a fixed light, appears
on the display.
3. Enter the new code .
The flashing character is displayed.
4. Enter the new code a second time.
If the new code has been correctly entered, it is accepted and this is
confirmed when the buzzer beeps twice;otherwise, an error warning
is given and the system exits the procedure.
Example of code change
- The master user wishes to change the factory code 1-11111.
- Typein 111111 on the keypadand press the
C
** key,thecharacter
lights up with a fixed light.
- Enter the new code, for example, 165744.The on the display
begins to flash, and re-enters the numbers 165744.
- The code is accepted when the buzzer beeps twice.
2.2 Enabling/Disabling the User 2, Engineer’s,
Telemonitoring and Key Codes
1. Enter the MASTER code.
2. Press the
F
key followed by the
C
** key.A flashingline appears
onthe display.
It is now possible to enable/disable the engineer’s code, the
telemonitoring code, the User2 codeand the keycode.These 4 codes
are associated with the 4 leds present on the keypad:
ENGINEER
TELEMONITORING
USER 2
KEY CODE (EK)
3. Pressthe keynexttothe ledfor enabling/disablingthe corresponding
code.
4. Press the EXIT
F
key to exit the procedure.
The leds respectively indicate the
status of the codes:
Led ON = Code enabled
Led OFF = Code disabled
The key code cannot be
changed: when enabled, it
allows use of the electronic
keysand of the commutators.
When disabled, it prevents
the operation of all the
commutators and of existing
keys(only system status will
be displayed by the
commutators’ leds).
KEY
CODE
Note: the first number
of the code must be the
user’s identification
number:
1for master user
2for user 2
3for engineer
4for telemonitoring
5 for user 5
6for user 6
7for user 7
8for user 8.
20