ElMod ThinkTank Tank Module ECO Assembly instructions

ThinkTank Tank Module ECO
Instructions for assembly and handling
Please read this document carefully!
Product contents
•ThinkTank Tank Module ECO PCB •motor connectors
•ready to use power supply cable set •proportional receiver cable set
Overview
1 Power supply
Fuse for turret elements
3 Connector for left chain motor
4 Connector for right chain motor
5 Setup mode push button
6 DIP-switches for selecting the tank profile
7 Connector for HengLong® muzzle flash, AsiaTam® recoil unit and PC Configurator
8 Connector for HengLong® muzzle flash
9 Connector for turret elements
10 Connector for Tamiya® recoil unit
11 Connector for proportional receiver (marked red)
L Status LED
Assembly
HINT: the function of all connectors is printed on the back side of the PCB!
Power supply
Solder the loose ends of the power supply cable to a battery connector that fits to your battery type. Use the included shrinking tube to
insulate the soldered wires.
Warning! The use of the switch and fuse is mandatory! Fire hazard when disregarded!
Chain motors
Use the included plugs to connect the motors to the board. Keep the wires as short as possible. To check the correct wiring of the motors
perform the following procedure:
•Jack the tank up, so that the chains can move freely.
•Attach a full charged battery to the power supply connector and switch the electronics on.
•Wait 3-4 seconds and press the pushbutton.
•The chains start to move. They change the running direction every 4 seconds. Release the button when both chains move forwards and
the light chain runs faster than the left one.
•Go ahead with the installation when the motors run in described manner.
Turret elements
Connect the white 8-pin turret plug to the corresponding connector.
•If using the genuine HengLong® LED muzzle flash, attach it's cables (a 5-wire and a -wire cable) to the board.
•If using the genuine AsiaTam® turret mechanics and high voltage muzzle flash, proceed as described in the
manual of the units.
•If using the genuine Tamiya® recoil unit, attach it to the corresponding connector on the board. The white cable
faces the edge of the board.
Choosing the tank profile
The driving and function setup is determined by the position of the DIP switches. The Tank Module ECO offers seven fixed and one user
defined profile
German, WW , plastic
gearboxes
German, WW , 3:1
reducted gearbox
US, WW , metal
gearboxes
easy-to-drive tank
German, WW , metal
gearboxes
US, WW , plastic
gearboxes
T-34 User defined, setup used by the
ThinkTank Configurator and PC
Configurator
tatus LED
The onboard LED shows the current status of the module
on Tank Module is in operational state *no connection to the sender or the transmission path between
sender and receiver is disturbed. Please check the wiring and the
proper function of the RC radio and receiver. If necessary check
the operability of the RC equipment with a servo.
**undervoltage on the CPU detected. Switch the power off for 10
seconds. If the error remains, assure that the PC Configurator USB
dongle is disconnected and retry.
Short going out Stick movement detected
Fast blinking No valid signal from receiver*
Slow blinking Faulty communication with another module
Double blinking Faulty CPU power supply**
RC receiver
The receiver cable MUST NOT be attached to the turret elements connector (connector #9)! This will unavoidable cause a damage of the
receiver. The proportional cable is already attached to the proper red marked connector #11 on delivery. Don't remove it if you are unsure
about the wiring.
© ElMod GbR - 13-08-16

The Tank Module ECO may be connected with four, five or six channel receiver. The currently active mode of operation is recognized
automatically. Please consider that the radio must be setup correctly (all mixers must be deactivated, the servo deflection must be 100% and
the trimming is centered)
If the channels five and/or six are used, they must be equipped either as a slider, knob or 3-way-switch (up-off-down). Otherwise only four-
channel operation is possible (although mostly all functions are also available with only four channels). The wires of unused channels may
not be connected to the receiver.
The TankModule electronics provides the power supply for the receiver (BEC, stabilized 5V DC) via the red/black wires which are part of the
proportional cable set.
The receiver cable has to be attached to the receiver connector on the Tank Module. The wire color pin assignment is as follows:
Ch. Control 4-ch. mode 4+1-ch. mode 5-ch. mode 5+1-ch. mode
1rechter Knüppel Acceleration Acceleration Acceleration Acceleration
2Steering Steering Steering Steering
3linker Knüppel Turret, weapon and special
functions
Turret, weapon and special
functions Turret and weapon control Turret and weapon control
4
53-way switchr Not connected Not connected Ignition and light Ignition and light
63-way switch Not connected User defined sounds User defined sounds User defined sounds
Depending on the receiver it may be necessary to adjust the channel order or swap its movement direction. Check the manual of your rc gear
for details.
Turret, weapon and special functions using 4-channels mode
This mode is active if the blue wire of the receiver cable isn't attached to the receiver. The turret, weapon and special functions are controlled
solely by the left stick of the radio.
Left stick (channels 3 and 4)
éLift the main gun (half deflection) éShot (maximum deflection)
êLower the main gun (half deflection) êMachine gun (maximum deflection)
èRotate turret right Main light on/off
çRotate turret left Ignition (requires ThinkTank Blaster)
Turret, weapon and special functions using 5-channels mode
This mode is active if the blue wire of the receiver cable is attached to the receiver. The turret and weapon functions are controlled by the left
stick of the radio, ignition and light is mapped to the 3-way switch connected to channel 5 of the radio.
Left stick (channels 3 and 4) witch (channel 5)
éLift the main gun (half deflection) éShot (max. deflection) éIgnition (requires TTank Blaster)
êLower the main gun (half deflection) êMachine gun (max. defl.) êMain light on/off
èRotate turret right
çRotate turret left
User defined sounds
If a ThinkTank Blaster is connected to the ThankModule ECO, up to two user defined sounds may be activated optionally by the user. To use
this feature, the violet wire of the receiver cable has to be attached to the 6th channel of the receiver .The samples are activated by switching
the corresponding control in the radio to upper most (user sample 1) or lower most (user sample ) position. The playback may be aborted by
moving the switch in the opposite direction.
Under voltage protection
The TankModule features an under voltage protection to protect the batteries from deep discharge. On delivery the threshold voltage is set to
6 volts for 7. V NiMh/NiCd batteries. If the voltage drops below 6 volts, the tank stops and the main light starts to blink. In this case replace or
recharge the battery.
Fuse for turret elements
The element # on the PCB is a safety fuse for the turret motors. The fuse blows if the total current of the turret motors excesses amps
which never happens under normal conditions. In this case no turret function is given (turret rotation, elevation, shot) and all lights are off.
Check the wiring for shortcuts and the mechanics for blockages. Replace the damaged fuse with a new one. The fuses are available as spare
parts in our shop.
Configuration and update
An optionally available USB cable, the PC Configurator allows a very detailed configuration and setup of the Tank Module. To run the
configuration download and install the PC Configurator Software from our web site, attach the USB cable and power up the Tank Module.
If a new firmware version for the Tank Module is released, it may also be uploaded with the PC Configurator. To activate the update process
download and install the current version of the PC Configurator Software, attach the USB cable, press and hold the pushbutton on the Tank
Module and switch on the power. The LED on the Tank Module blinks exactly 3 times. Follow the directions shown by the PC Configurator
Software.
Nicht geeignet für Kinder unter 14 Jahren. Not suitable for Children under 14 years.
Ne convient pas pour des enfants de moins de 14 ans. Niet geschikt voor kinderen onder de 14 jaar.
ElMod Thomas Kusch, M. Sc. & Jürgen K. Huber GbR
Enzenhardtweg 11
D-7 6 Nürtingen
ElMod Th. Kusch, M. c. & Jürgen K. Huber GbR
[email protected] http://www.elmod.eu
© ElMod GbR - 13-08-16