emaux V700B User manual

1-4
Models: V700(B) / V800 V900 V1000 V1200 / / /
(Link by Nuts type Valves)
EMF I16 030 752
FUNCTION
INSTALLATION
The filter uses special filter sand to remove dirt particles from pool water. The filter sand is loaded into the filter tank and
functions as a permanent dirt removing media. When the control valve is in the FILTER position, the pool water which
contains suspended dirt particles, is pumped through your piping system and is automatically directed by the
patented filter control valve to the top of the filter tank. As the pool water is pumped through the filter, dirt particles are
trapped by the sand bed, and filtered out. The cleaned pool water is returned from the bottom of the filter tank,
through the control valve and back to the pool through the piping system. This entire sequence is continuous and
automatic. It provides for total recirculation of pool water through your filter and piping system.
After a period of time, the accumulated dirt in the filter causes a resistance to flow, and the flow diminishes. This means
it is time to clean your filter. With the control valve in the BACKWASH position, the water flow is automatically reversed
through the filter so that it is directed to the bottom of the tank, up through the sand, flushing the previously trapped dirt
and debris out the waste line. Once the filter is back-washed of dirt, set control valve to RINSE position and run pump for
about 1/2 to 1 minute, and then set the control valve in the FILTER position, to resume normal filtering.
NOTE: Turn pump off before changing valve position.
Only simple tools (screwdriver and wrenches), plus pipe sealant for plastic adapters, are required to install and service the
filter.
1) The filter should be placed on a level concrete slab, very firm ground, or equivalent. The filter should be placed
2) Loading the sand media. Filter sand media is loaded through the top opening of the filter.
a) Loosen the flange clamp and remove filter control valve (if previously installed).
b) Cap internal pipe with plastic cap to prevent sand from entering it.
c) We recommend filling the tank approximately 1/2 way with water to provide a cushion effect when the filter sand is
poured in. This helps protect the under-drain laterals from excessive shock.
d) Carefully pour in correct amount and grade of filter sand. (Be sure center pipe remains centered in opening.) Sand
surface should be leveled and should come to about the middle of the filter tank. Remove plastic cap from internal
pipe.
WARNING
4-4
By-passes filter for circulating water to pool
Used after backwash to flush dirt from valve
Cleaning Filter by reversing the flow
By-passes filter, used for vacuuming to waste or lowering water level
CLOSED Shuts off all flow to filter or pool
RECIRCULATE
WASTE
RINSE
BACKWASH
FILTER
Valve Position
Normal Filtration and Vacuuming
Function
FUNCTIONS OF VALVE POSITIONS
WASTE
FILTER
BACKWASH RINSE
WASTE
RECIRCULATE
CLOSED
WASTE WASTE
WASTE WASTE WASTE
IN FLOW OUT FLOW IN FLOW OUT FLOW IN FLOW OUT FLOW
IN FLOW OUT FLOW IN FLOW OUT FLOW IN FLOW OUT FLOW
GENERAL
1) Pipe tap boss provided for optional influent pressure gauge.
2) SERVICING VALVE( Stop pump,close gate valve in suction&discharge before proceeding):
a) Set handle in filter position. b) Remove cover screws. c) Lift cover and key assembly out.
TO ASSEMBLE:
1) Place valve key so that wedge opening is at TOP port (handle in Filter psn.). Flat edge of cover screw lug should
align with flat edge of body screw lug.
2) Position cover O'Ring.
3) Secure assembly to body with cover screws. Tighten cover screws evenly and alternately. Do not over-tighten.
THIS FILTER OPERATES UNDER HIGH PRESSURE. WHEN ANY PART OF THE CIRCULATING SYSTEM
(e.g., CLAMP, PUMP, FILTER, VALVES, ETC.) IS SERVICED, AIR CAN ENTER THE SYSTEM AND
BECOME PRESSURIZED . PRESSURIZED AIR CAN CAUSE THE LID OR VALVE TO BE BLOWN OFF
WHICH CAN RESULT IN SEVERE INJURY, DEATH, OR PROPERTY DAMAGE.
TURN PUMP OFF BEFORE CHANGING VALVE POSITION.
TO PREVENT DAMAGE TO THE PUMP AND FOR PROPER OPERATION OF THE SYSTEM, CLEAN
PUMP STRAINER AND SKIMMER BASKETS REGULARLY.
DO NOT UNSCREW SCREWS OF FLANGE CLAMP WHILE PUMP IS RUNNING.

B
A
MAIN DIMENSION
3) Assemble filter control valve into the filter tank.
a) Insert filter control valve (with O'ring in place) into the tank neck, taking care that the center pipe slips into the
hole in the bottom of the valve.
b) Place two plastic clamps around valve flange and tank flange and tighten just enough so that the valve may
be rotated on tank for final positioning.
c) Carefully screw pressure gauge (with O'ring in place) into tapped hole in valve body. Do not over-tighten.
d) Connect pump to control valve opening marked PUMP. After connections are made, tighten valve flange
clamps with screwdriver, tapping around clamp with screwdriver handle to help seat valve flange clamp.
4) Make return to pool pipe connection to control valve opening marked RETURN and complete other necessary
plumbing connections, suction lines to pump, waste, etc.
5) Make electrical connections to pump per pump instructions.
6) To prevent water leakage, make sure all pipe connections are tight.
REPLACEMENT PARTS OF MULTIPORT VALVE
DIMENSION TABLE
2-4
REPLACEMENT PARTS OF FILTER
3-4
1300
1200
A
V900
V800 800
900
B
Model
High Diameter
mm
mm
1400V1000 1000
1600V1200 1200
Inch
Valve Port
Size Sand
kg
470
355
620
860
2"
2"
2"
2"
1092V700(B) 723 215
2"
Key No.
Part No.
Product Descriptio n
Qty
1
01013003
Handle (Big )
1
2
03018008
Pin for Handle
1
3
01181027
Washer for Handle
1
4
89280301
M6*32 Screw with Nut
10
5
01013019
2.0"Top Mount Valve Standa rd Lid (Black)
1
6
03014014
Spring for 2.0" Top Mount Valve
1
7
02011006
O-Ring for 2.0" Top Mount Valve L id
1
8
02011022
O-Ring for 2.0" Top Mount Valve R otor
2
9
01181002
Washer for Spring
2
10
01021002
2.0" Valve Rotor
1
11
02311003
Spider Gasket
1
12
01013027
2.0" Top Mount Valve Bottom B ody (black)
1
13
01013029
2.0" Water Tube
1
14
01013030
2.0" Diffuser
1
15
02011005
O-Ring for Diffuser
1
16
02020016
O-Ring for Connector
6
17
01013031
2.0"Connector with Exter nal Thread (Black)
3
18
01171154
2.0"Union Adaptor
3
19
01013032
2.0"Union Nut (Bl ack)
3
20
89280104
Sight Glass with O-Ring
1
21
01111048
Connector for Pressu re Gauge/Stoppe r
1
22
89021303
Drain Plug with O-ring
1
23
06011029
Oil Pressure Gauge Wit h O-ring (40psi)
1
1) Make sure the correct amount of filter media sand is located in the tank and all connections have been
connected and secured.
2) Depress control valve handle and rotate to BACKWASH position. (To prevent damage to control valve seal, always
depress handle before turning.)
3) Prime and start pump according to pump instructions (be sure all suction and return lines are open), allowing the
filter tank to fill with water. Once water is flowing out of the waste line, run the pump for at least 1 minute. The initial
back-washing of the filter is recommended to remove any impurities or fine sand particles in the sand media.
4) Turn pump off and set valve to RINSE position. Start pump and operate until water in sight glass is clear, about 1/2 to
1 minute. Turn pump off and set valve to FILTER position and restart pump. The filter is now operating in the normal
filter mode, filtering dirt particles from the pool water.
5) Adjust pool suction and return valves to achieve desired flow. Check system and filter for water leaks and tighten
connections, bolts, nuts, as required.
6) Note the initial pressure gauge reading when the filter is clean. (It will vary from pool to pool depending upon the
pump and general piping system.) As the filter removes dirt and impurities from the pool water, the accumulation
of dirt in the filter will cause the pressure to rise and diminish the water flow. When the pressure gauge reading is 1.5
bar, higher than the initial "clean" pressure you noted, it is time to backwash the filter (see BACKWASH under filter
and control valve functions).
INSTALL/START-UP OF FILTER
NOTE: During initial clean-up of the pool water it may be necessary to backwash frequently due to the unusually
heavy initial dirt load in the water.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
16
18
19
20
21
22
23
Key No.
Part No.
Description
Qty
1
89010601
Nut with Washer
12
2
88280351B
6 Way 2" Valve with 2" union set x 3
and pressure gauge (Bl ack)
1
3
06011029
Maximum 40PSI Indication, Stainles s
Steel Casing
1
4
89280103B
2.0" Union with O-Ring ( Black)
3
5
89280104
Sight Glass with O-Ring
1
6
02011126
Filter Neck Gasket
1
7
89010612
V700B Filter Tank with Base
1
7
89010603
V800 Filter Tank with Base
1
7
89010604
V900 Filter Tank with Base
1
7
89010605
V1000 Filter Tank with Base
1
7
89010606
V1200 Filter Tank with Base
1
8
89010611
V700B Standpipe with hub
1
8
89010607
V800 Standpipe with Hub
1
8
89010608
V900 Standpipe with Hub
1
8
89010609
V1000 Standpipe with Hub
1
8
89010610
V1200 Standpipe with Hub
1
9
01172010
Laterals (185mm)
8
9
01172011
Laterals (233mm)
8
9
89010613
Laterals(129mm & 185mm)
8
9
89010614
Laterals(129mm & 233mm)
8
10
89010107
Water Drain Set
1
11
01111062
21-28inch Filter Base
1
11
01112038
32-40 inch Filter Base
1
11
01112039
Base for V1200
1
Notes:9* 01172010 Laterals (185mm) for V700B
9* 01172011 Laterals (233mm) for V800 & V900
9* 89010613 Laterals (129mm & 185mm) for V1000
9* 89010614 Laterals (129mm & 233mm) for V1200