Emerson Rosemount 705 User manual

Quick Start Guide
00825-0200-4705, Rev AA
August 2014
Rosemount 705 Wireless Totalizing
Transmitter
An installation-ready solution that provides simple and easy connection to a
pulse source
Measure average flow and totalized volume
Flow and volume are continuously measured between wireless updates
Self-organizing network delivers information rich data with >99% data
reliability totalized volume
00825-0200-4705_RevAA.fm Page 1 Monday, August 4, 2014 3:48 PM

August 2014
2
Quick Start Guide
Required equipment
Measuring tape
Standard tools (e.g. screwdriver, wrench, pliers)
Anti-seize paste or PTFE tape (for threaded connection)
AMS®Wireless Configurator version 12.0 or later, or Field Communicator
Explosions could result in death or serious injury.
Installation of device in an explosive environment must be in accordance with appropriate local,
national and international standards, codes, and practices.
Ensure device is installed in accordance with intrinsically safe or non-incendive field practices.
Electrical shock can result in death or serious injury.
Ground device to prevent electrostatic charge build-up.
Care must be taken during transportation of power module to prevent electrostatic charge
build-up.
Device must be installed to ensure a minimum antenna separation distance of 8 in. (20 cm)
from all persons.
Process leaks could result in death or serious injury.
Handle the transmitter carefully.
Failure to follow safe installation guidelines could result in death or serious injury.
Only qualified personnel should install the equipment.
NOTICE
This guide provides basic guidelines for the Rosemount 705. It does not provide instructions for
detailed configuration, diagnostics, maintenance, service, troubleshooting, or installations.
Refer to the Rosemount 705 Reference Manual (document number 00809-0200-4705) for
more instruction. This guide and the manual are available electronically on
www.emersonprocess.com.
Shipping considerations for wireless products:
The unit was shipped without the power module installed. Remove the power module prior to
shipping the unit.
Each power module contains two “C” size primary lithium batteries. Primary lithium batteries
are regulated in transportation by the U.S. Department of Transportation, and are also covered
by IATA (International Air Transport Association), ICAO (International Civil Aviation
Organization), and ARD (European Ground Transportation of Dangerous Goods). It is the
responsibility of the shipper to ensure compliance with these or any other local requirements.
Consult current regulations and requirements before shipping.
00825-0200-4705_RevAA.fm Page 2 Monday, August 4, 2014 3:48 PM

Quick Start Guide
3
August 2014
Step 1: Install pulse output device
Step 2: Seal and protect threads
Use anti-seize paste or PTFE tape according to your site procedures.
Conduit entries
Upon installation, ensure each conduit entry is either sealed with a conduit plug
with appropriate thread sealant, or has an installed conduit fitting or cable gland
with appropriate thread sealant. Note the conduit entries on the Rosemount 705
Totalizer are threaded 1/2-14 NPT.
A. Conduit entry
Step 3: Mount 705 on pulse input device
General considerations
Physical installation
The Rosemount 705 Totalizer and all other wireless devices should not be set up
until after the Smart Wireless Gateway has been installed and is functioning
properly.
The transmitter can be installed in one of two configurations:
Direct Mount, where the pulse output device is connected directly to the
transmitter housing’s conduit entry
Remote Mount, where the pulse output device is mounted separate from the
transmitter housing, then connected to the transmitter via conduit
Choose the installation sequence that corresponds to the mounting
configuration.
AA
00825-0200-4705_RevAA.fm Page 3 Monday, August 4, 2014 3:48 PM

August 2014
4
Quick Start Guide
Direct mount
Note
Direct mount installation should not be employed when using tubing and connectors such as
Swagelok®fittings.
1. Install the pulse output device according to standard installation practices
making sure to use thread sealant on all connections.
2. Attach the pulse output device wiring to the terminals as indicated on the
wiring diagram (reference figures on page 15 through page 30).
3. Attach the transmitter housing to the pulse output device using the threaded
conduit entry.
Note
Wireless devices should be powered up with the proper join key and network ID in order of
proximity from the Smart Wireless Gateway. Beginning with the closest device to the Smart
Wireless Gateway will result in a faster network installation.
4. Connect the Black Power Module.
5. Close the housing cover and tighten to safety specification. Always ensure a
proper seal so that metal touches metal, but do not over tighten.
6. Position the antenna so it is vertical, either straight up or straight down.
00825-0200-4705_RevAA.fm Page 4 Monday, August 4, 2014 3:48 PM

Quick Start Guide
5
August 2014
a. The antenna should be approximately 3-ft. (0.91 m) from any large
structures or buildings, to allow clear communication to other devices.
Remote mount
1. Install the pulse output device according to standard installation practices
making sure to use thread sealant on all connections.
2. Run wiring (and conduit if necessary) from the pulse output to the Rosemount
705 Totalizer.
3. Pull the wiring through the threaded conduit entry of the transmitter.
4. Attach the wiring to the terminals as indicated on the wiring diagram.
Note
Wireless devices should be powered up with the proper join key and network ID in order of
proximity from the Smart Wireless Gateway. Beginning with the closest device to the Gateway will
result in a faster network installation.
5. Connect the Black Power Module.
Possible antenna rotation shown.
Antenna rotation allows for best
installation practices in any
configuration.
00825-0200-4705_RevAA.fm Page 5 Monday, August 4, 2014 3:48 PM

August 2014
6
Quick Start Guide
6. Close the housing cover and tighten to safety specification. Always ensure a
proper seal so that metal touches metal, but do not over tighten.
7. Position the antenna vertically and straight up.
a. The antenna should be approximately 3-ft. (0.91 m) from any large
structures or buildings, to allow clear communication to other devices.
00825-0200-4705_RevAA.fm Page 6 Monday, August 4, 2014 3:48 PM

Quick Start Guide
7
August 2014
Remote antenna (optional)
The remote antenna option provides flexibility for mounting the Rosemount 705
Totalizer based on wireless connectivity, lightning protection, and current work
practices.
The remote mount antenna kit includes coaxial sealant for the cable connections
for the lightning arrestor and antenna.
Find a location where the remote antenna has optimal wireless performance.
Ideally this will be 15-25 ft. (4.6 - 7.6 m) above the ground or 6 ft. (2 m) above
obstructions or major infrastructure. To install the remote antenna, use one of
the following procedures. The WN option is 25 ft. (7.6 m) and the WJ option is 10
ft. (3 m).
WN/WJ remote antenna option
1. Mount the antenna on a 1.5-2 in. pipe mast using the supplied mounting
equipment.
2. Connect the lightning arrestor directly to the top of the Rosemount 705
Totalizer.
3. Install the grounding lug, lock washer, and nut on top of lightning arrestor.
4. Connect the antenna to the lightning arrestor using the supplied LMR-400
coaxial cable ensuring the drip loop is not closer than 1 ft. (0.3 m) from the
lightning arrestor.
5. Use the coaxial sealant to seal each connection between the wireless field
device, lightning arrestor, cable, and antenna.
6. Ensure the mounting mast and lightning arrestor are grounded according to
local/national electrical code.
Note
Any spare lengths of coaxial cable should be placed in 12 in. (0.3 m) coils.
When installing remote mount antennas for the transmitter, always use established safety
procedures to avoid falling or contact with high-power electrical lines.
Install remote antenna components for the transmitter in compliance with local and national
electrical codes and use best practices for lightning protection.
Before installing, consult with the local area electrical inspector, electrical officer, and work
area supervisor.
The transmitter remote antenna option is specifically engineered to provide installation
flexibility while optimizing wireless performance and local spectrum approvals. To maintain
wireless performance and avoid non-compliance with spectrum regulations, do not change
the length of cable or the antenna type.
If the supplied remote mount antenna kit is not installed per these instructions, Emerson
Process Management is not responsible for wireless performance or non-compliance with
spectrum regulations.
00825-0200-4705_RevAA.fm Page 7 Monday, August 4, 2014 3:48 PM

August 2014
8
Quick Start Guide
Figure 1. Rosemount 705 Totalizer with Remote Antenna
Note
Weather proofing is required! The remote mount antenna kit includes coaxial sealant for weather
proofing the cable connections for the lightning arrestor, antenna, and Rosemount 705 Totalizer.
Coaxial sealant must be applied to guarantee performance of the wireless field network. See
Figure 2 for details on how to apply coaxial sealant.
Figure 2. Applying Coaxial Sealant to Cable Connections
00825-0200-4705_RevAA.fm Page 8 Monday, August 4, 2014 3:48 PM

Quick Start Guide
9
August 2014
Step 4: Insert black power module
Power up sequence
The Smart Wireless Gateway should be installed and functioning properly before
any wireless field devices are powered. Install the Black Power Module,
SmartPower™Solutions model number 701PBKKF (part number
00753-9220-0001) into the transmitter to power the device.
Wireless devices should be powered up in order of proximity from the Gateway,
beginning with the closest device, then working outward from the Gateway. This
results in a faster network installation. Enable Active Advertising on the Gateway
to ensure new devices are able to join the network faster. For more information
see the Smart Wireless Gateway Manual (document number 00809-0200-4420).
Step 5: Connect to device
A. Field Communicator
B. Communication terminals
C. HART®Modem
D. AMS Device Manager
AMS Wireless Configurator
1. Start AMS Wireless Configurator.
2. In the View menu, select Device Connection View.
3. Double click on the device under the HART modem.
123
456
78
0
9
D
A
C
B
00825-0200-4705_RevAA.fm Page 9 Monday, August 4, 2014 3:48 PM

August 2014
10
Quick Start Guide
Field Communicator
1. Turn on the Field Communicator.
2. Tap the HART symbol on the main menu.
The Field Communicator now connects to the device.
Field Communicator connections
The power module needs to be installed before the Field Communicator can
interface with the transmitter. This transmitter uses the Black Power Module;
order model number 701PBKKF.
Step 6: Configure device using Guided Setup
a. Go to Configure > Guided Setup > Initial Setup.
b. Select Basic Setup and follow the instructions.
c. Select Verify operation to check your flow measurement.
d. Consider optional setup, such as Update Rate and Device Display.
Step 7: Join device to network
a. Go to Overview > Shortcuts.
b. Select Configure Update Rate and follow the instructions.
c. Obtain Network ID and Join Key for the wireless network (available in wireless
gateway).
d. Select Join Device to Network and follow the instructions.
00825-0200-4705_RevAA.fm Page 10 Monday, August 4, 2014 3:48 PM