Empire Comfort Systems FBB10-1 User manual

37709-2-0220 Page 1Empire Comfort Systems Inc. • Belleville, IL
DVC (C,P) MODELS
BEFORE FIREPLACE IS INSTALLED IN THE WALL
1. With power completely turned off, remove plate and four
screws as shown. See Figure 1.
Figure 1
2. Install the blower onto the pre-bent brackets on the blower
plate. Ensure the Velcro connects to secure the blower in
place. See Figure 2.
Figure 2
3. Route wiring through opening created in step 1.
4. Secure plate and blower assembly into place with four screws.
5. Install thermo-disc by snapping into valve bracket under the
burner assembly. See Figure 3.
Figure 3
6. Connect Power source into outlet on bottom right side of
replace.
FOR USE ON: DVC(C,P)(32,36,42)BP - (SEE PAGE 1) AND DVCX(36,42)FP - (SEE PAGE 5)
INSTRUCTIONS MUST BE LEFT WITH THE OWNER FOR FUTURE REFERENCE AFTER INSTALLATION.
INSTALLATION INSTRUCTIONS
FBB10-1 BLOWER

37709-2-0220Page 2 Empire Comfort Systems Inc. • Belleville, IL
AFTER FIREPLACE IS INSTALLED IN THE WALL
ATTENTION: Do not handle barrier screen or door assembly
with bare hands! (Always wear gloves)
1a. (Post 2016) Make sure power and gas are turned off prior to
any removal. Lift barrier screen assembly and pull away from
the unit. See Figure 4.
Figure 4
1b. (Pre 2016) Make sure power and gas are turned off. Tilt
and pull lower panel to remove from bottom assembly. See
Figure 5.
If applicable, remove safety barrier screen covering the
glass.
Figure 5
2. Undo two latches at the bottom of the rebox assembly.
See Figure 6.
Figure 6
3. Disengage glass frame by pulling in upward swinging position.
Place glass frame aside in a safe and out-of-the-way location.
See Figure 7.
Figure 7

37709-2-0220 Page 3Empire Comfort Systems Inc. • Belleville, IL
4. Remove log set and decorative media. Remove brackets
and liners if installed. Retain for re-installation. See Figure 8.
(Reective liners shown.)
Figure 8
5. Remove burner cover by lifting off. See Figure 9.
Figure 9
6. Remove log support by removing the two screws securing the
metal plate to log support. Retain log support and screws for
reassembly. See Figure 10.
Figure 10
7. Remove the four screws securing burner, slide to burner right
and lift off burner. Retain burner and screws for reassembly.
See Figure 11.
Figure 11

37709-2-0220Page 4 Empire Comfort Systems Inc. • Belleville, IL
8. Remove ten screws and lift burner base assembly. Disconnect
gas line. Retain burner and screws for reassembly. See
Figure 12.
Figure 12
9.
Remove the four #10 X 1/2" screws securing the latch
assembly to the underside of the rebox and set aside. See
Figure 13.
Figure 13
10. Install blower through burner cutout. See Figure 14.
Figure 14
11. The blower plate is on the left side of the replace. Slide the
blower up into the tabs, securing it into place with the velcro.
See Figure 15.
Figure 15
12. Reinstall the latch assembly removed in step 9. See Figure 13.
13. Install thermo disc by snapping it into bracket under the
burner assembly. See Figure 16.
Figure 16
14. Turn gas on, check for leaks. Reinstall the burner base
assembly and ten screws removed in step 8. See Figure 12.
15. Reinstall the burner and four screws removed in step 7.
See Figure 11.
16. Reinstall the log support and secure it with the metal plate and
two screws removed in step 6. See Figure 10.
17. Replace burner cover removed in step 5. See Figure 9.
18. Replace liner and bracket, if removed in step 4.
19. Replace log set and decorative media.
20. Turn on power.
21. Reinstall the glass frame removed in step 3. See Figure 7.
22. Secure the glass frame with the latches at the bottom of the
replace. See Figure 6.
23a.Replace barrier screen removed in step 1a. See Figure 4.
23b.Replace lower panel removed in step 1b. See Figure 5.
Back side of Blower
showing Velcro
Back side of Blower
showing Velcro
Back side of Blower
showing Velcro
Back side
of blower
showing
Velcro

37709-2-0220 Page 5Empire Comfort Systems Inc. • Belleville, IL
DVCX MODELS
BLOWER INSTALLATION (AFTER INSTALLED IN WALL)
1. Make sure power is turned off. Tilt and pull lower panel to
remove from bottom assembly. See Figure 17.
Figure 17
If applicable, remove safety barrier screen covering the glass.
2. Pull latches toward you and down to release.
See Figure 18.
Figure 18
3. Pull glass out at the bottom, then lift up and off. See Figure 19.
Figure 19
4. Install blower through bottom opening. See Figure 20.
Figure 20
5. The blower plate is on the left side of the replace. Slide the
blower up into the tabs. Secure it into place with the Velcro
at the bottom. See Figure 21.
Figure 21

37709-2-0220Page 6 Empire Comfort Systems Inc. • Belleville, IL
6. Install thermo-disc by snapping into bracket under the burner
assembly. See Figure 22.
30 SERIES 70 SERIES
Figure 22
7. Connect power.
8. Reinstall the glass frame and safety barrier screen removed
in step 3. See Figure 19.
9. Secure the glass frame with the latches at the bottom of the
replace. See Figure 5.
10. Replace lower panel removed in step 1. See Figure 15.
11. Turn power on.

37709-2-0220 Page 7Empire Comfort Systems Inc. • Belleville, IL
6
2
3
4
1
5
7
BLOWER ASSEMBLY PARTS LIST
Index Number Part Number Description Quantity
1 R2804 BLOWER ASSEMBLY 1
2 R7649 FAN CONTROL L120-20 1
3 R2099 CORD SET, 30" 1
4 R4192 RHEOSTAT, KNOB 1
5 R4186 RHEOSTAT, 3.0 AMP 115 VAC 1
6 10088 RHEOSTAT BOX BRACKET 1
7 R11768 WIRE HARNESS,
FAN CONTROL 1

37709-2-0220Page 8
www.empirecomfort.com
Empire Comfort Systems Inc.
Belleville, IL
If you have a general question
about our products, please e-mail
us at [email protected].
If you have a service or repair
question, please contact your dealer.

37709-2-0220 Page 1Empire Comfort Systems Inc. • Belleville, IL
MODÈLES DVC (C,P)
AVANT L’INSTALLATION DU FOYER DANS LE MUR
1. Après avoir coupé l’alimentation électrique, enlever les
quatre vis et la plaque comme montré à la Figure 1.
Figure 1
2. Installer la souferie sur les supports prévus à cet effet sur
la plaque de montage. S’assurer que les attaches en Velcro
sont réunies an de maintenir la souferie en place. Voir
Figure 2.
Figure 2
3. Acheminer le câblage par l’ouverture créée à l’étape 1.
4. À l’aide de quatre vis, xer l’ensemble souferie et plaque de
montage à l’intérieur.
5. Installer le thermodisque en l’enclenchant dans le support
prévu à cet effet sous l’ensemble de soupape de brûleur. Voir
Figure 3.
Figure 3
6. Raccorder la source d’alimentation à la prise de courant sur
le côté inférieur droit du foyer.
POUR UTILISATION SUR : DVC(C,P)(32,36,42)BP - (VOIR PAGE 1) ET DVCX(36,42)FP - (VOIR PAGE 5)
APRÈS LE MONTAGE, LE FEUILLET D’INSTALLATION DOIT ÊTRE
LAISSÉ AU PROPRIÉTAIRE POUR CONSULTATION ULTÉRIEURE.
INSTRUCTION D’INSTALLATION
POUR SOUFFLERIE FBB10-1

37709-2-0220Page 2 Empire Comfort Systems Inc. • Belleville, IL
APRÈS L’INSTALLATION DU FOYER DANS LE MUR
ATTENTION : Ne pas manipuler l’écran de protection et la
porte à mains nues! (Toujours porter des gants)
1a. (Unités de l’année de production 2016 et ultérieures)
S’assurer que l’alimentation électrique et l’arrivée de gaz
sont coupées avant de faire toute intervention. Soulever
l’ensemble écran protecteur et l’e retirer l’appareil. Voir
Figure 4.
Figure 4
1b. (Unités fabriquées avant l’année de production 2016)
S’assurer que l’alimentation électrique et l’arrivée de gaz
sont coupées avant de faire toute intervention. Incliner et
retirer le panneau inférieur. Voir Figure 5.
Le cas échéant, déposer l’écran protecteur de la vitre.
Figure 5
2. Désenclencher les deux loquets sous l’âtre du foyer. Voir
Figure 6.
Figure 6
3. Décrocher la vitre encadrée en la tirant et en la basculant
vers le haut. Mettre la vitre encadrée de côté en lieu sûr. Voir
Figure 7.
Figure 7