Enclume PR14 User manual

Enclume FOUR POINT OVAL RACK
PR14
Enclume racks are the ultimate in
Quality, design, strength and function.
Congratulations for owning one of the finest
Storage racks made.
WARNING:
READ ALL OF THE INSTRUCTIONS
BEFORE ASSEMBLING AND USING
YOUR RACK.
All of our hammered steel racks are finished with an industrial wax designed to
give years of protection to the rack. Cleaning is easily done with a damp cloth. Dry
thoroughly after cleaning. If a touch-up is ever needed we recommend a "Pledge"
like wax product.
Enclosed you will find everything needed for the assembly
and use of your storage rack. Two people make assembly
and installation easier. The parts and hardware included are:
Components included:
1 – Oval Base
4 – Hanging Straps
4 – C-Rings
12 –Angled Pot Hooks (
4 – Ceiling Screw Hooks
If you have also purchased a grid (sold and packaged separately)
you will also have received:
1 – Grid
6 – Straight Pot Hooks
6 – Grid Brackets
See reverse side for ASSEMBLY AND INSTALLATION INSTRUCTIONS
If you need help, please call 1-877-ENCLUME
Enclume Design Products, Inc.
24 Colwell Street, Port Hadlock, WA. 98339
Phone [phone] •Fax [phone]
www.enclume.com
Limited Warranty: This product is warranted to be free of material defects for a period of five years from the date of purchase. Customer's exclusive remedy shall
be the repair or replacement of the defective product and shall be subject to the following conditions: (1) notice of any defect is received by Enclume within the
warranty period and (2) customer returns the defective product to Enclume Design Products, Inc. , 24 Colwell St.. , Port Hadlock, WA 98339, postage prepaid
within 20 days following a return authorization number (which may be obtained by telephoning the number at the bottom of this instructions) being provided to the
customer by Enclume. There are no other warranties, expressed or implied. THERE ARE NO WARRANTIES OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE. ENCLUME SPECIFICALLY DISCLAIMS ANY AND ALL INCIDENTAL OR CONSEQUENTIAL DAMAGES
ARISING OUT OF THE PURCHASE OR USE OF ENCLUME'S PRODUCTS.

ASSEMBLY AND INSTALLATION INSTRUCTIONS for PR14
Enclosed you will find everything needed for the assembly
and use of your storage rack. Two people make assembly
and installation easier. The parts and hardware included are:
Components included:
1 – Oval Base
4 – Hanging Straps
4 – C-Rings
12 – Angled Pot Hooks
4 – Ceiling Screw Hooks
If you have also purchased a grid (sold and packaged separately)
you will also have received:
1 – Grid
6 – Straight Pot Hooks
6–GridBrackets Angled Hooks
ASSEMBLY AND INSTALLATION INSTRUCTIONS
Grid Insertion (if you have not purchased a grid, please continue on the rack assembly instructions)
1) Slip the 6 grid brackets over the oval base with the “L” portion pointing to the inside. Center one bracket on each end and on the
inside of each hanging bracket.
2) Place the grid on the brackets. You are now ready to assemble the rack.
3) Hang you pot hooks from interior squares only. Do not hang them from the perimeter or the cut portions of the grid. Distribute
your cookware evenly.
4) The grid has been treated with a finish which will resist corrosion and tarnish. It can be cleaned with a damp cloth and dried
thoroughly. Please do not use abrasive cleaners.
Rack Assembly
1) If your rack is plated, it is best to keep the tissue on during installation to avoid fingerprinting.
2) Slip the oval into the U at the bottom of each hanging strap. To maintain maximum stability, the straps should be spaced at least
16” apart along each straight side of the oval.
3) Your rack must be anchored into solid wood of ceiling joists or beams. Plasterboard or wall fasteners will not work and should
not be used. Carefully measure the area where the rack is to be hung and install the ceiling screw hooks. Your local hardware
store can advise you if special hardware is needed for your particular kitchen.
4) Distribute your cookware evenly around the rack.
5) All of our hammered steel racks are finished with an industrial wax designed to give years of protection to the rack. Cleaning is
easily done with a damp cloth. Dry thoroughly after cleaning. If a touch-up is ever needed we recommend a "Pledge" like wax
product.
6) The care and cleaning of our copper and brass units must be done with a low abrasive cleaner such as “Flitz”. Chrome racks are
best cleaned with a good quality glass cleaner like “Windex”. Our high quality plating will age & tarnish the same as solid
material. A periodic cleaning will restore your rack to its original brilliance
It is important that your rack is assembled correctly. If the unit is assembled or used incorrectly, it
could become unstable and collapse, possibly causing injury.
Enclume Design Products, Inc.
24 Colwell Street, Port Hadlock, WA. 98339
Phone [phone] •Fax [phone]
www.enclume.com
WARNING