Enclume Gourmet Island GI1 User manual

Enclume Gourmet Island
GI1
Enclume’s display, baking and storage units are the ultimate in
quality, design, strength and function.
Congratulations for selecting one of the finest
multi-function kitchen units manufactured today.
WARNING:
Please read all of these instructions before
assembling and using your Gourmet Island
Enclosed you will find everything needed for the
assembly of your Gourmet Island. Two people
working together make assembly much easier.
Please unpack, identify and lay out all of the pieces
before starting assembly.
Components:
2 – Steel shelf rims
1 – Wood butcher-block work surface
1 – Steel oval trim band
2 – Steel grid shelves
Hardware:
1 – 7/32” Allen wrench
1 5/32” Allen wrench
4 – ¼” x 7/8” Button head screws
20 – 3/8” x ½” Button head screws
See reverse side for Assembly and Installation Instructions.
It is important that your rack is assembled correctly. If the unit is assembled or
used incorrectly, it could become unstable and collapse, possibly causing
injury.
Phone [phone]
www.enclume.com
WARNING
This product is warranted to be free of material defects for a period of one year from the date of purchase. Customer's exclusive remedy for breach of this warranty
shall be the repair or replacement of the defective product when delivered, postage prepaid, to Enclume Design Products, Inc. at 24 Colwell St. Port Hadlock, WA.
98339. There is no other warranty, expressed or implied, and there is specifically NO WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PORPOSE. In no event will Enclume Design Products, Inc. be responsible for any incidental or consequential damages.
Enclume Design Products, Inc.
24 Colwell Street, Port Hadlock, WA. 98339
85-6100 •Fax 360

ssembly and Installation Instruction for the Gourmet IslandA
Components:
2 – Steel shelf rims
1 – Wood butcher-block work surface
d
– Steel grid shelves
0 – 3/8” x ½” Button head screws
ssembly and Installation Instructions:
fe use and
ach other – about 24” apart. The long side of the uprights
ide the uprights through the inside
her side using eight of the 3/8” x ½” button head screws in the same
e steel oval trim band to the outside of the rectangular upright. This uses the remaining four 3/8” x ½” button head
hrough the holes in the bottom of the work surface and tightening them down with the smaller 5/32”
durability
care must be taken to insure the highest performance of the unit.
amp cloth. Dry thoroughly after cleaning. If the finish ever
ng with swings in humidity, we strongly
recommend oiling the entire wood surface every four to six weeks.
Phone [phone]
www.enclume.com
1 – Steel oval trim ban
2
Hardware:
1 – 7/32” Allen wrench
1 5/32” Allen wrench
4 – ¼” x 7/8” Button head screws
2
A
1) wi
Please proceed carefully and slowly through the following instructions to insure this unit assembly properly for sa
thout damage to its wood and steel finishes. Haste in assembly could result in needless scratching or marring.
2) Lay the rectangular uprights on the floor in correct relationship to ewith the double holes punched should be placed against the floor.
3) Slide the shelf rims inside the rectangular uprights one at a time. Notice the rivet placement around the ovals. The rivets
will be closer to the bottom of the rim than the top. The positioning allows the steel grid shelves to set deeply inside the shelf
rims. Align holes from the shelves to holes in the rectangular uprights and attach from outs
of the shelves with four 3/8” x ½ “ button head screws per shelf. Leave the screws loose.
4) Stand the unit upright and attach the shelves to the otmanner as done in Step 3. Leave the screws loose.
5) Attach thscrews.
6) Square up the entire unit using a carpenter’s square and tighten down all screws.
7) Slide the two oval grid shelves into the lower and middle shelf rims with the long wire of the grid facing upward.
8) Place the wood butcher-block work surface on the top of the unit, rough surface facing down. The work surface should have
a 1” overhand around the oval trim band. Align the holes in the bottom of the work surface with the slotted holes on the tops
of the rectangular uprights. Attach the work surface with ¼” x 7/8” button head screws, inserting the screws upward through
the slots in the uprights t
Allen wrench provided.
9) Your Gourmet Island is manufactured out of the finest materials, with finishes applied to enhance beauty, increase
and minimize maintenance. Nevertheless, some
Accordingly please take note of the following.
a) The steel sections of your Gourmet Island are coated with an industrial finish designed to give years of
protection. Cleaning can be done easily with a d
needs a touch-up, use a “Pledge” type product.
b) The wood butcher-block surface has been penetrated with a food-grade mineral oil and its edges sealed. To
maintain the natural beauty of the wood and to avoid possible splitti
Enclume Design Products, Inc.
24 Colwell Street, Port Hadlock, WA. 98339
85-6100 •Fax 360