Endon EL-40085 User manual

The Light pack contains:
IP44 rated Wall light.
The following tools may be required:
Selection of cross and flat head screwdrivers.
Electric drill and assorted drill bits.
Wire strippers.
Electrical insulation tape.
INSTRUCTION MANUAL
This product is only suitable for connection to a 240V~50Hz supply.
It is recommended that this wall light is installed by a qualified electrician in accordance with current IEE
Wiring Regulations and local Building Regulations and is for the Domestic environment only.
The light fitting should be connected to a lighting circuit protected by a 5 amp fuse (or a 6 amp miniature
circuit breaker).
This light has an IP44 rating suitable for use outdoors.
Run supply wire from a 5-amp electrical supply using double insulated 3-core cable of type H05RN-F 1.0mm2
(not supplied) to selected site, ensuring it is adequately protected through the full length of the cable run, it
must come out of the mounting surface in line with the entry to the fitting.
Except where installed in a conduit or duct , which provides equivalent protection against mechanical damage,
a cable buried in the ground shall incorporate an earthed armour or metal sheath or both, suitable for use as a
protective conductor, or be of insulated concentric construction. Buried cables shall be marked by cable
covers or a suitable marking tape. Buried conduits and ducts shall be suitably identified. Buried cables,
conduits and ducts shall be at a sufficient depth to avoid being damaged by any reasonably foreseeable
disturbance of the ground.
This product contains breakable parts – be careful during handling and maintenance to avoid breakage.
This light fitting is intended to use a Compact Fluorescent Lamp (23w) (not supplied).
If any part of the bulb housing is broken or cracked then it cannot be replaced and the fittings must not be
used - as the water ingress protection has been compromised.
If any modification is made it will invalidate the warranty and may render the product unsafe.
Before you start
Please read these instructions carefully before fitting your new light and retain for reference.
Switch off the mains supply and remove the appropriate fuse or switch off the appropriate circuit breaker
before commencing installation.
Ensure that no one else has access that would enable the supply to be inadvertently reconnected.
Check the packaging and make sure that you have all the required parts.
Follow each assembly step in order to prevent incorrect assembly
Make sure all screws / nuts, including electrical connections etc are fully tightened before use.
AS THIS UNIT IS DESIGNED TO USE A CFL TYPE LAMP AND THESE ARE, GENERALLY, NOT DIMMABLE, DO
NOT CONNECT THIS PRODUCT TO A DIMMER SWITCH / EXTERNAL PIR UNIT.
EL-40085 - Outdoor wall fitting.
Safety Warnings

Endon Lighting
LS9 0SE
20151112
These assembly diagrams are intended as a guide – if in doubt consult a qualified electrician.
Assembly / user instructions
C280 004
Diagram A
Diagram B
Diagram C
1. Determine the position of your
light fitting. Make sure there is
sufficient cable coming out of
the wall to connect to the
terminal block. Ensure that the
mounting surface is solid,
preferably a brick or block wall
and ensure that there are no
other cables or pipes beneath
the surface.
2. Diagram A. If the back plate
bracket is attached – remove
it by undoing the single grub
screw. Use the back plate
bracket as a template and
mark the 2 fixings holes,
making sure the back plate is
the correct way up and the
sides of the back plate are
vertical. Use appropriate
fixings to secure the back
plate to the wall.
3. Diagram B. Open the terminal
block housing (A) by taking
out the screws (B) at either
side of the housing. Connect
the mains wiring to the
internal terminal block (C) –
see wiring details. The cable
entry grommet (D) and any
seals (E) must be securely in
place to ensure that the water
ingress protection is
maintained. NOTE: This is a
Class I fitting and must be
earthed.
4. Diagram C. Fit the terminal
block housing together and
secure with the screws –
removed in 3 above. Fit the
front frame over the back
plate and secure with the
single grub screw removed in
2 above. Take care not to trap
or strain the internal cables.
5. Unscrew the top cover and fit
the recommended CFL lamp –
not supplied. NOTE: Do not
fit lamps of a higher wattage
than those recommended as
this may cause overheating
and damage the fitting.
Re-fit the cover over the lamp.
6. Turn on the power and test.
Back plate
bracket
Incoming mains
cable
WIRING DETAILS
Bracket Grub
screw
(A)
(A)
(B)
(B)
(C)
(C)
(C)
(D)
(E)