Endress+Hauser Proline Prosonic Flow E 100 HART User manual

Products Solutions Services
Operating Instructions
Proline Prosonic Flow E 100
HART
Ultrasonic time-of-flight flowmeter
BA01769D/06/EN/02.19
71455467
2019-11-01
Valid as of version
01.00.zz (Device firmware)

Proline Prosonic Flow E 100 HART
2 Endress+Hauser
• Make sure the document is stored in a safe place such that it is always available when
working on or with the device.
• To avoid danger to individuals or the facility, read the "Basic safety instructions" section
carefully, as well as all other safety instructions in the document that are specific to
working procedures.
• The manufacturer reserves the right to modify technical data without prior notice. Your
Endress+Hauser Sales Center will supply you with current information and updates to
these instructions.

Proline Prosonic Flow E 100 HART Table of contents
Endress+Hauser 3
Table of contents
1 About this document ................ 5
1.1 Document function ..................... 5
1.2 Symbols used .......................... 5
1.2.1 Safety symbols .................. 5
1.2.2 Electrical symbols ................ 5
1.2.3 Tool symbols .................... 5
1.2.4 Symbols for
certain types of information ......... 6
1.2.5 Symbols in graphics ............... 6
1.3 Documentation ........................ 6
1.3.1 Standard documentation ........... 7
1.3.2 Supplementary device-dependent
documentation .................. 7
1.4 Registered trademarks ................... 7
2 Basic safety instructions ............ 8
2.1 Requirements for the personnel ............ 8
2.2 Designated use ........................ 8
2.3 Workplace safety ....................... 9
2.4 Operational safety ...................... 9
2.5 Product safety ......................... 9
2.6 IT security ........................... 10
3 Product description ................ 11
3.1 Product design ........................ 11
3.1.1 Device version with HART
communication type ............. 11
4 Incoming acceptance and product
identification ..................... 12
4.1 Incoming acceptance ................... 12
4.2 Product identification ................... 12
4.2.1 Transmitter nameplate ........... 13
4.2.2 Sensor nameplate ............... 14
5 Storage and transport ............. 15
5.1 Storage conditions ..................... 15
5.2 Transporting the product ................ 15
5.2.1 Measuring devices without lifting
lugs ......................... 15
5.2.2 Measuring devices with lifting lugs .. 16
5.2.3 Transporting with a fork lift ........ 16
5.3 Packaging disposal ..................... 16
6 Installation ....................... 16
6.1 Installation conditions .................. 16
6.1.1 Mounting position ............... 16
6.1.2 Requirements from environment and
process ....................... 18
6.2 Mounting the measuring device ........... 19
6.2.1 Required tools .................. 19
6.2.2 Preparing the measuring device ..... 19
6.2.3 Mounting the measuring device ..... 19
6.2.4 Turning the display module ........ 20
6.3 Post-mounting check ................... 20
7 Electrical connection .............. 21
7.1 Connection conditions .................. 21
7.1.1 Required tools .................. 21
7.1.2 Requirements for connecting cable ... 21
7.1.3 Terminal assignment ............. 22
7.1.4 Preparing the measuring device ..... 22
7.2 Connecting the measuring device .......... 23
7.2.1 Connecting the transmitter ........ 23
7.2.2 Ensuring potential equalization ..... 24
7.3 Special connection instructions ............ 25
7.3.1 Connection examples ............. 25
7.4 Ensuring the degree of protection .......... 26
7.5 Post-connection check .................. 26
8 Operation options ................. 27
8.1 Overview of operating options ............ 27
8.2 Structure and function of the operating
menu .............................. 28
8.2.1 Structure of the operating menu .... 28
8.2.2 Operating philosophy ............ 29
8.3 Access to the operating menu via the web
browser ............................. 30
8.3.1 Function range ................. 30
8.3.2 Prerequisites ................... 30
8.3.3 Establishing a connection ......... 31
8.3.4 Logging on .................... 32
8.3.5 User interface .................. 33
8.3.6 Disabling the Web server .......... 34
8.3.7 Logging out .................... 34
8.4 Access to the operating menu via the
operating tool ........................ 35
8.4.1 Connecting the operating tool ...... 35
8.4.2 Field Xpert SFX350, SFX370 ....... 36
8.4.3 FieldCare ..................... 36
8.4.4 DeviceCare .................... 38
8.4.5 AMS Device Manager ............ 38
8.4.6 SIMATIC PDM .................. 38
8.4.7 Field Communicator 475 .......... 38
9 System integration ................ 39
9.1 Overview of device description files ......... 39
9.1.1 Current version data for the device ... 39
9.1.2 Operating tools ................. 39
9.2 Measured variables via HART protocol ...... 39
9.3 Other settings ........................ 40
10 Commissioning .................... 43
10.1 Function check ....................... 43

Table of contents Proline Prosonic Flow E 100 HART
4 Endress+Hauser
10.2 Switching on the measuring device ......... 43
10.3 Setting the operating language ............ 43
10.4 Configuring the measuring device .......... 43
10.4.1 Defining the tag name ............ 43
10.4.2 Setting the system units .......... 44
10.4.3 Configuring the current output ..... 46
10.4.4 Configuring the pulse/frequency/
switch output .................. 47
10.4.5 Configuring the output
conditioning ................... 54
10.4.6 Configuring the low flow cut off ..... 56
10.5 Advanced settings ..................... 57
10.5.1 Using the parameter to enter the
access code .................... 57
10.5.2 Carrying out a sensor adjustment .... 57
10.5.3 Configuring the totalizer .......... 58
10.5.4 Configuration management ........ 58
10.5.5 Carrying out additional display
configurations .................. 60
10.5.6 Using parameters for device
administration ................. 62
10.6 Simulation ........................... 63
10.7 Protecting settings from unauthorized
access .............................. 65
10.7.1 Write protection via write protection
switch ........................ 66
11 Operation ......................... 67
11.1 Reading the device locking status .......... 67
11.2 Adjusting the operating language .......... 67
11.3 Configuring the display ................. 67
11.4 Reading measured values ................ 67
11.4.1 Process variables ................ 67
11.4.2 System values .................. 68
11.4.3 Output values .................. 69
11.4.4 "Totalizer" submenu .............. 69
11.5 Adapting the measuring device to the process
conditions ........................... 70
11.6 Performing a totalizer reset .............. 70
11.6.1 Function scope of the "Control
Totalizer" parameter ............. 71
11.6.2 Function scope of the "Reset all
totalizers" parameter ............. 71
12 Diagnostics and troubleshooting ... 72
12.1 General troubleshooting ................. 72
12.2 Diagnostic information via light emitting
diodes .............................. 73
12.2.1 Transmitter .................... 73
12.3 Diagnostic information in the Web browser .. 74
12.3.1 Diagnostic options ............... 74
12.3.2 Calling up remedy information ...... 75
12.4 Diagnostic information in FieldCare or
DeviceCare .......................... 75
12.4.1 Diagnostic options ............... 75
12.4.2 Calling up remedy information ...... 76
12.5 Adapting the diagnostic information ....... 76
12.5.1 Adapting the diagnostic behavior .... 76
12.5.2 Adapting the status signal ......... 77
12.6 Overview of diagnostic information ........ 77
12.7 Pending diagnostic events ............... 80
12.8 Diagnostic list ........................ 81
12.9 Event logbook ........................ 81
12.9.1 Reading out the event logbook ...... 81
12.9.2 Filtering the event logbook ........ 82
12.9.3 Overview of information events ..... 82
12.10 Resetting the measuring device ........... 83
12.10.1 Function scope of the "Device reset"
parameter ..................... 83
12.11 Device information .................... 83
12.12 Firmware history ...................... 85
13 Maintenance ...................... 86
13.1 Maintenance tasks ..................... 86
13.1.1 Exterior cleaning ................ 86
13.2 Measuring and test equipment ............ 86
13.3 Endress+Hauser services ................ 86
14 Repairs ........................... 87
14.1 General notes ........................ 87
14.1.1 Repair and conversion concept ...... 87
14.1.2 Notes for repair and conversion ..... 87
14.2 Spare parts .......................... 87
14.3 Endress+Hauser services ................ 87
14.4 Return .............................. 87
14.5 Disposal ............................ 88
14.5.1 Removing the measuring device ..... 88
14.5.2 Disposing of the measuring device ... 88
15 Accessories ....................... 89
15.1 Communication-specific accessories ........ 89
15.2 Service-specific accessories ............... 90
15.3 System components .................... 90
16 Technical data .................... 91
16.1 Application .......................... 91
16.2 Function and system design .............. 91
16.3 Input ............................... 91
16.4 Output ............................. 92
16.5 Power supply ......................... 94
16.6 Performance characteristics .............. 95
16.7 Installation .......................... 97
16.8 Environment ......................... 97
16.9 Process ............................. 97
16.10 Mechanical construction ................ 99
16.11 Operability ......................... 101
16.12 Certificates and approvals .............. 103
16.13 Application packages .................. 104
16.14 Accessories ......................... 104
16.15 Supplementary documentation ........... 104
Index ................................. 106

Proline Prosonic Flow E 100 HART About this document
Endress+Hauser 5
1 About this document
1.1 Document function
These Operating Instructions contain all the information that is required in various phases
of the life cycle of the device: from product identification, incoming acceptance and
storage, to mounting, connection, operation and commissioning through to
troubleshooting, maintenance and disposal.
1.2 Symbols used
1.2.1 Safety symbols
Symbol Meaning
DANGER
DANGER!
This symbol alerts you to a dangerous situation. Failure to avoid this situation will
result in serious or fatal injury.
WARNING
WARNING!
This symbol alerts you to a dangerous situation. Failure to avoid this situation can
result in serious or fatal injury.
CAUTION
CAUTION!
This symbol alerts you to a dangerous situation. Failure to avoid this situation can
result in minor or medium injury.
NOTICE
NOTE!
This symbol contains information on procedures and other facts which do not result in
personal injury.
1.2.2 Electrical symbols
Symbol Meaning
Direct current
Alternating current
Direct current and alternating current
Ground connection
A grounded terminal which, as far as the operator is concerned, is grounded via a
grounding system.
Protective Earth (PE)
A terminal which must be connected to ground prior to establishing any other
connections.
The ground terminals are situated inside and outside the device:
• Inner ground terminal: Connects the protectiv earth to the mains supply.
• Outer ground terminal: Connects the device to the plant grounding system.
1.2.3 Tool symbols
Symbol Meaning
Allen key
Open-ended wrench

About this document Proline Prosonic Flow E 100 HART
6 Endress+Hauser
1.2.4 Symbols for certain types of information
Symbol Meaning
Permitted
Procedures, processes or actions that are permitted.
Preferred
Procedures, processes or actions that are preferred.
Forbidden
Procedures, processes or actions that are forbidden.
Tip
Indicates additional information.
Reference to documentation.
A
Reference to page.
Reference to graphic.
Notice or individual step to be observed.
1.
,
2.
,
3.
… Series of steps.
Result of a step.
Help in the event of a problem.
Visual inspection.
1.2.5 Symbols in graphics
Symbol Meaning
1, 2, 3, ... Item numbers
1.
,
2.
,
3.
, … Series of steps
A, B, C, ... Views
A-A, B-B, C-C, ... Sections
-
Hazardous area
.
Safe area (non-hazardous area)
Flow direction
1.3 Documentation
For an overview of the scope of the associated Technical Documentation, refer to the
following:
• The W@M Device Viewer : Enter the serial number from the nameplate
(www.endress.com/deviceviewer)
• The Endress+Hauser Operations App: Enter the serial number from the nameplate
or scan the 2-D matrix code (QR code) on the nameplate.
For a detailed list of the individual documents along with the documentation code
→  104

Proline Prosonic Flow E 100 HART About this document
Endress+Hauser 7
1.3.1 Standard documentation
Document type Purpose and content of the document
Technical Information Planning aid for your device
The document contains all the technical data on the device and provides
an overview of the accessories and other products that can be ordered for
the device.
Sensor Brief Operating Instructions Guides you quickly to the 1st measured value - Part 1
The Sensor Brief Operating Instructions are aimed at specialists with
responsibility for installing the measuring device.
• Incoming acceptance and product identification
• Storage and transport
• Installation
Transmitter Brief Operating
Instructions
Guides you quickly to the 1st measured value - Part 2
The Transmitter Brief Operating Instructions are aimed at specialists with
responsibility for commissioning, configuring and parameterizing the
measuring device (until the first measured value).
• Product description
• Installation
• Electrical connection
• Operation options
• System integration
• Commissioning
• Diagnostic information
Description of Device Parameters Reference for your parameters
The document provides a detailed explanation of each individual
parameter in the Expert operating menu. The description is aimed at
those who work with the device over the entire life cycle and perform
specific configurations.
1.3.2 Supplementary device-dependent documentation
Additional documents are supplied depending on the device version ordered: Always
comply strictly with the instructions in the supplementary documentation. The
supplementary documentation is an integral part of the device documentation.
1.4 Registered trademarks
HART®
Registered trademark of the FieldComm Group, Austin, Texas, USA
Microsoft®
Registered trademark of the Microsoft Corporation, Redmond, Washington, USA

Basic safety instructions Proline Prosonic Flow E 100 HART
8 Endress+Hauser
2 Basic safety instructions
2.1 Requirements for the personnel
The personnel for installation, commissioning, diagnostics and maintenance must fulfill
the following requirements:
‣Trained, qualified specialists must have a relevant qualification for this specific function
and task.
‣Are authorized by the plant owner/operator.
‣Are familiar with federal/national regulations.
‣Before starting work, read and understand the instructions in the manual and
supplementary documentation as well as the certificates (depending on the
application).
‣Follow instructions and comply with basic conditions.
The operating personnel must fulfill the following requirements:
‣Are instructed and authorized according to the requirements of the task by the facility's
owner-operator.
‣Follow the instructions in this manual.
2.2 Designated use
Application and media
Depending on the version ordered, the measuring device can also measure potentially
explosive, flammable, poisonous and oxidizing media.
Measuring devices for use in hazardous areas, in hygienic applications or where there is an
increased risk due to process pressure, are labeled accordingly on the nameplate.
To ensure that the measuring device remains in proper condition for the operation time:
‣Keep within the specified pressure and temperature range.
‣Only use the measuring device in full compliance with the data on the nameplate and
the general conditions listed in the Operating Instructions and supplementary
documentation.
‣Based on the nameplate, check whether the ordered device is permitted for the
intended use in the hazardous area (e.g. explosion protection, pressure vessel safety).
‣Use the measuring device only for media to which the process-wetted materials are
sufficiently resistant.
‣If the measuring device is not operated at atmospheric temperature, compliance with
the relevant basic conditions specified in the associated device documentation is
absolutely essential: "Documentation" section→  6.
‣Protect the measuring device permanently against corrosion from environmental
influences.
Incorrect use
Non-designated use can compromise safety. The manufacturer is not liable for damage
caused by improper or non-designated use.
LWARNING
Danger of breakage due to corrosive or abrasive fluids!
‣Verify the compatibility of the process fluid with the sensor material.
‣Ensure the resistance of all fluid-wetted materials in the process.
‣Keep within the specified pressure and temperature range.

Proline Prosonic Flow E 100 HART Basic safety instructions
Endress+Hauser 9
NOTICE
Verification for borderline cases:
‣For special fluids and fluids for cleaning, Endress+Hauser is glad to provide assistance
in verifying the corrosion resistance of fluid-wetted materials, but does not accept any
warranty or liability as minute changes in the temperature, concentration or level of
contamination in the process can alter the corrosion resistance properties.
Residual risks
LWARNING
The electronics and the medium may cause the surfaces to heat up. This presents a
burn hazard!
‣For elevated fluid temperatures, ensure protection against contact to prevent burns.
2.3 Workplace safety
For work on and with the device:
‣Wear the required personal protective equipment according to federal/national
regulations.
For welding work on the piping:
‣Do not ground the welding unit via the measuring device.
If working on and with the device with wet hands:
‣Due to the increased risk of electric shock, gloves must be worn.
2.4 Operational safety
Risk of injury.
‣Operate the device in proper technical condition and fail-safe condition only.
‣The operator is responsible for interference-free operation of the device.
Conversions to the device
Unauthorized modifications to the device are not permitted and can lead to unforeseeable
dangers.
‣If, despite this, modifications are required, consult with Endress+Hauser.
Repair
To ensure continued operational safety and reliability,
‣Carry out repairs on the device only if they are expressly permitted.
‣Observe federal/national regulations pertaining to repair of an electrical device.
‣Use original spare parts and accessories from Endress+Hauser only.
2.5 Product safety
This measuring device is designed in accordance with good engineering practice to meet
state-of-the-art safety requirements, has been tested, and left the factory in a condition in
which it is safe to operate.
It meets general safety standards and legal requirements. It also complies with the EU
directives listed in the device-specific EU Declaration of Conformity. Endress+Hauser
confirms this by affixing the CE mark to the device.

Basic safety instructions Proline Prosonic Flow E 100 HART
10 Endress+Hauser
2.6 IT security
We only provide a warranty if the device is installed and used as described in the
Operating Instructions. The device is equipped with security mechanisms to protect it
against any inadvertent changes to the device settings.
IT security measures in line with operators' security standards and designed to provide
additional protection for the device and device data transfer must be implemented by the
operators themselves.

Proline Prosonic Flow E 100 HART Product description
Endress+Hauser 11
3 Product description
The device consists of a transmitter and a sensor.
The device is available as a compact version:
The transmitter and sensor form a mechanical unit.
3.1 Product design
3.1.1 Device version with HART communication type
3
2
1
4
5
6
7
A0023153
 1 Important components of a measuring device
1 Sensor
2 Transmitter housing
3 Main electronics module
4 Transmitter housing cover
5 Transmitter housing cover (version for optional local display)
6 Local display (optional)
7 Main electronics module (with bracket for optional local display)

Incoming acceptance and product identification Proline Prosonic Flow E 100 HART
12 Endress+Hauser
4 Incoming acceptance and product
identification
4.1 Incoming acceptance
A0028673
1
2
1
2
Are the order codes on the
delivery note (1) and the
product sticker (2) identical?
A0028673
Are the goods undamaged?
A0028673
Order code:
Ser. no.:
Ext. ord. cd.:
ii
Date:
Do the nameplate data
match the ordering
information on the delivery
note?
A0028673
Is the CD-ROM with the
Technical Documentation
(depends on device version)
and documents present?
• If one of the conditions is not satisfied, contact your Endress+Hauser Sales Center.
• Depending on the device version, the CD-ROM might not be part of the delivery!
The Technical Documentation is available via the Internet or via the Endress+Hauser
Operations App, see the "Product identification" section →  13.
4.2 Product identification
The following options are available for identification of the measuring device:
• Nameplate specifications
• Order code with breakdown of the device features on the delivery note
• Enter serial numbers from nameplates in W@M Device Viewer
(www.endress.com/deviceviewer): All information about the measuring device is
displayed.
• Enter the serial number from the nameplates into the Endress+Hauser Operations App
or scan the 2-D matrix code (QR code) on the nameplate with the Endress+Hauser
Operations App: all the information for the measuring device is displayed.

Proline Prosonic Flow E 100 HART Incoming acceptance and product identification
Endress+Hauser 13
For an overview of the scope of the associated Technical Documentation, refer to the
following:
• The chapters "Additional standard documentation on the device" →  7 and
"Supplementary device-dependent documentation" →  7
• The W@M Device Viewer: Enter the serial number from the nameplate
(www.endress.com/deviceviewer)
• The Endress+Hauser Operations App: Enter the serial number from the nameplate or
scan the 2-D matrix code (QR code) on the nameplate.
4.2.1 Transmitter nameplate
i
1
2
3
4
5
6
7
8
9
101112
Order code:
Ext. ord. cd.:
Ser. no.:
13
A0030222
 2 Example of a transmitter nameplate
1 Manufacturing location
2 Name of the transmitter
3 Order code
4 Serial number (ser. no.)
5 Extended order code (Ext. ord. cd.)
6 Electrical connection data, e.g. available inputs and outputs, supply voltage
7 Permitted ambient temperature (Ta)
8 Degree of protection
9 2-D matrix code
10 Document number of safety-related supplementary documentation
11 Manufacturing date: year-month
12 CE mark, C-Tick
13 Firmware version (FW)

Incoming acceptance and product identification Proline Prosonic Flow E 100 HART
14 Endress+Hauser
4.2.2 Sensor nameplate
Date:
Size:
Material:
Tm:
Patents
i
Ptest =
i
Order code:
Ext. ord. cd.:
Ser. no.:
322541-0000
0044
11
1
2
3 4 5 6 7
12
8
9
13 14 15
16
17
19
18
10
A0013907
 3 Example of a sensor nameplate
1 Manufacturing location
2 Name of the sensor
3 Order code
4 Serial number (ser. no.)
5 Extended order code (Ext. ord. cd.)
6 Nominal diameter of sensor
7 Test pressure of the sensor
8 Flange nominal diameter/nominal pressure
9 Material of measuring tube and manifold
10 Medium temperature range
11 CE mark, C-Tick
12 Additional information on version: certificates, approvals
13 Manufacturing date: year-month
14 Flow direction
15 2-D matrix code
16 Degree of protection
17 Approval information for explosion protection and Pressure Equipment Directive
18 Permitted ambient temperature (Ta)
19 Document number of safety-related supplementary documentation
Order code
The measuring device is reordered using the order code.
Extended order code
• The device type (product root) and basic specifications (mandatory features) are
always listed.
• Of the optional specifications (optional features), only the safety and approval-
related specifications are listed (e.g. LA). If other optional specifications are also
ordered, these are indicated collectively using the # placeholder symbol (e.g. #LA#).
• If the ordered optional specifications do not include any safety and approval-related
specifications, they are indicated by the + placeholder symbol (e.g. XXXXXX-ABCDE
+).

Proline Prosonic Flow E 100 HART Storage and transport
Endress+Hauser 15
5 Storage and transport
5.1 Storage conditions
Observe the following notes for storage:
‣Store in the original packaging to ensure protection from shock.
‣Do not remove protective covers or protective caps installed on process connections.
They prevent mechanical damage to the sealing surfaces and contamination in the
measuring tube.
‣Protect from direct sunlight to avoid unacceptably high surface temperatures.
‣Store in a dry and dust-free place.
‣Do not store outdoors.
Storage temperature→  97
5.2 Transporting the product
Transport the measuring device to the measuring point in the original packaging.
A0029252
Do not remove protective covers or caps installed on process connections. They
prevent mechanical damage to the sealing surfaces and contamination in the
measuring tube.
5.2.1 Measuring devices without lifting lugs
LWARNING
Center of gravity of the measuring device is higher than the suspension points of the
webbing slings.
Risk of injury if the measuring device slips.
‣Secure the measuring device against slipping or turning.
‣Observe the weight specified on the packaging (stick-on label).
A0029214

Installation Proline Prosonic Flow E 100 HART
16 Endress+Hauser
5.2.2 Measuring devices with lifting lugs
LCAUTION
Special transportation instructions for devices with lifting lugs
‣Only use the lifting lugs fitted on the device or flanges to transport the device.
‣The device must always be secured at two lifting lugs at least.
5.2.3 Transporting with a fork lift
If transporting in wood crates, the floor structure enables the crates to be lifted lengthwise
or at both sides using a forklift.
5.3 Packaging disposal
All packaging materials are environmentally friendly and 100% recyclable:
• Measuring device secondary packaging: polymer stretch film that conforms to EC
Directive 2002/95/EC (RoHS).
• Packaging:
• Wood crate, treated in accordance with ISPM 15 standard, which is confirmed by the
affixed IPPC logo.
or
• Carton in accordance with European Packaging Directive 94/62EC; recyclability is
confirmed by the affixed RESY symbol.
• Seaworthy packaging (optional): Wood crate, treated in accordance with ISPM 15
standard, which is confirmed by the affixed IPPC logo.
• Carrying and mounting hardware:
• Disposable plastic pallet
• Plastic straps
• Plastic adhesive strips
• Dunnage: Paper cushion
6 Installation
6.1 Installation conditions
No special measures such as supports etc. are necessary. External forces are absorbed by
the construction of the device.
6.1.1 Mounting position
Mounting location
A0015543

Proline Prosonic Flow E 100 HART Installation
Endress+Hauser 17
Orientation
The direction of the arrow on the nameplate helps you to install the sensor according to
the flow direction (direction of medium flow through the piping).
• Install the measuring device in a parallel plane free of external mechanical stress.
• The internal diameter of the pipe must match the internal diameter of the sensor:
see the "Technical Information" device document, "Design and dimensions" section.
A0015895
Orientation Compact version
AVertical orientation
A0015545
BHorizontal orientation, transmitter
head up
A0015589
CHorizontal orientation, transmitter
head down
A0015590
DHorizontal orientation, transmitter
head at side
A0015592
Inlet and outlet runs
If possible, the sensor should be installed upstream from valves, T-pieces, elbows etc. To
attain the specified level of accuracy of the measuring device, the below mentioned inlet
and outlet runs must be maintained at minimum. If there are several flow disturbances
present, the longest specified inlet run must be maintained.
10 × DN 3 × DN
1
3
2
4
15 × DN 3 × DN
15 × DN 3 × DN10 × DN 3 × DN
A0033877
 4 Minimum inlet and outlet runs with various flow obstructions
1 90 ° elbow or T-section
2 Pump
3 2 × 90 ° elbow, 3-dimensional
4 Control valve

Installation Proline Prosonic Flow E 100 HART
18 Endress+Hauser
Outlet runs when installing external devices
If installing an external device, observe the specified distance.
3…5 × DN
PT
A0015901
PT Pressure
Installation dimensions
For the dimensions and installation lengths of the device, see the "Technical
Information" document, "Mechanical construction" section.
6.1.2 Requirements from environment and process
Ambient temperature range
Transmitter –25 to +60 °C (–13 to +140 °F)
Local display –20 to +60 °C (–4 to +140 °F), the readability of the display may be
impaired at temperatures outside the temperature range.
Sensor –25 to +60 °C (–13 to +140 °F)
‣If operating outdoors:
Avoid direct sunlight, particularly in warm climatic regions.
System pressure
It is important that cavitation does not occur, or that gases entrained in the liquids do not
outgas.
Cavitation is caused if the pressure drops below the vapor pressure:
In suction lines
‣Ensure the system pressure is sufficiently high to prevent cavitation and outgassing.
For this reason, the following mounting locations are recommended:
• At the lowest point in a vertical pipe
• Downstream from pumps (no danger of vacuum)
A0028777
Thermal insulation
In the case of some fluids, it is important to keep the heat radiated from the sensor to the
transmitter to a low level. A wide range of materials can be used for the required
insulation.

Proline Prosonic Flow E 100 HART Installation
Endress+Hauser 19
NOTICE
Electronics overheating on account of thermal insulation!
‣Observe maximum permitted insulation height of the transmitter neck so that the
transmitter head is completely free.
t
a
A0034104
t Maximum insulation thickness 2 cm (0.79 in)
a Minimum distance from transmitter to insulation
6.2 Mounting the measuring device
6.2.1 Required tools
For sensor
For flanges and other process connections: Corresponding mounting tools
6.2.2 Preparing the measuring device
1. Remove all remaining transport packaging.
2. Remove any protective covers or protective caps present from the sensor.
3. Remove stick-on label on the electronics compartment cover.
6.2.3 Mounting the measuring device
LWARNING
Danger due to improper process sealing!
‣Ensure that the inside diameters of the gaskets are greater than or equal to that of the
process connections and piping.
‣Ensure that the gaskets are clean and undamaged.
‣Install the gaskets correctly.
1. Ensure that the direction of the arrow on the sensor matches the flow direction of
the medium.
2. Install the measuring device or turn the transmitter housing so that the cable entries
do not point upwards.

A0029263

Installation Proline Prosonic Flow E 100 HART
20 Endress+Hauser
6.2.4 Turning the display module
The local display is only available with the following device version:
Order code for "Display; Operation", option B: 4-line; lit, via communication
The display module can be turned to optimize display readability.
Aluminum housing version, AlSi10Mg, coated
1.
2.
3.
4.
5.
6.
7.
4.
4.
3 mm
A0023192
6.3 Post-mounting check
Is the device undamaged (visual inspection)? 
Does the measuring device conform to the measuring point specifications?
For example:
• Process temperature
• Process pressure (refer to the section on "Pressure-temperature ratings" in the "Technical
Information" document)
• Ambient temperature range
• Measuring range

Has the correct orientation for the sensor been selected →  17?
• According to sensor type
• According to medium temperature
• According to medium properties (outgassing, with entrained solids)

Does the arrow on the sensor match the direction of flow of the medium through the piping
→  17? 
Are the measuring point identification and labeling correct (visual inspection)? 
Is the device adequately protected from precipitation and direct sunlight? 
Are the securing screw and securing clamp tightened securely? 