ENFORCER PA-U0405-NULQ User manual

PA-U0405-NULQ
4-Channel CCTV “Brick” Power Supply
Manual

ENFORCER 4-Channel CCTV “Brick” Power Supply
2SECO-LARM U.S.A., Inc.
Features:
4-Channel 5-Amp power distribution
Universal input voltage: 100~240 VAC
Adjustable output voltage: 12~13.8 VDC
Built-in 6.8-Amp overcurrent protection
High voltage and overcurrent protection
LED Power indicator
Mounting bracket included for easy installation
Parts List:
Power supply x1
Power cable x1
Specifications:
Outputs
4
Total supply current
5A
Max. output power
60W
Overcurrent protection
6.8A
Output voltage
12~13.8 VDC
Input fuse
3.15A@250VAC
Input voltage
100~240 VAC
Dimensions
57/8”x23/16”x15/16” (150x55x33 mm)
Weight
13.4-oz (380g)
Operating temperature
14°~113° F (-10°~45° C)
Overview:
Introduction:
The PA-U0405-NULQ is a 4-channel 5-Amp power supply. While normally used in CCTV
installations, it is suitable for a wide variety of both CCTV and access control applications. It
features adjustable output voltage and built-in 6.8-Amp overcurrent protection.
Top
Side
15/16”
(33mm)
LED Indicator
Output terminals
Output voltage
potentiometer
57/8” (150mm)
23/16”
(55mm)
Mounting bracket x1
Mounting screws x2
ENFORCER ®

ENFORCER 4-Channel CCTV “Brick” Power Supply
SECO-LARM U.S.A., Inc. 3
Installation:
1. Find a suitable location to install the power supply. The power supply should be installed
out of sight, and in a place protected from weather and high humidity. The power supply
must have adequate ventilation. Insufficient ventilation may cause overheating and
damage could result.
2. Attach the power supply to a wall or desk using the included mounting bracket. If
possible, mount the power supply sideways or with the terminals facing down so they do
not collect dust.
3. Connect the main power cable to the power supply.
Sample Installation:
Legend:
Positive (+):
Negative (–):
Installation:
Wiring and Adjusting Voltage:
1. Connect cameras and other devices to the power outputs, while observing correct
polarity as shown in Figure 1. To minimize voltage drop, use 18-gauge or larger wire.
WARNING: Always test output voltage before connecting devices to the power supply.
2. If voltage drop is large, adjust the output voltage potentiometer as shown in Figure 2.
Positive (+)
Negative (–)
Figure 1
ENFORCER ®
ENFORCER®
ENFORCER®
Figure 2
Min.
Max.

ENFORCER 4-Channel CCTV “Brick” Power Supply
4SECO-LARM U.S.A., Inc.
Troubleshooting:
CCTV
Power Supplies
Plug-in
AC Adapters
Plug-and-Play
Backup Power
Voltage
Converters
PS-U1812-PULQ
ST-UV12-S1.0Q
SB-L10V1-20Q
ST-LA130-TTQ
NOTICE: The information and specifications printed in this manual are current at the time of publication. However, the
SECO-LARM policy is one of continual development and improvement. For this reason, SECO-LARM reserves the right to
change specifications without notice. SECO-LARM is also not responsible for misprints or typographical errors. Trademarks
are the property of SECO-LARM U.S.A., Inc. or their respective owners.
Copyright © 2015 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or
in part, without the written permission of SECO-LARM.
LIMITED WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while
used in normal service for one (1) year from the date of sale to the original customer. SECO-LARM’s obligation is limited to
the repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM. This Warranty
is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or
alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such
equipment is not operating properly as a result of causes other than defects in material and workmanship. The sole
obligation of SECO-LARM and the purchaser’s exclusive remedy, shall be limited to the replacement or repair only, at
SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential
personal or property damage of any kind to the purchaser or anyone else.
SECO-LARM®U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Website: www.seco-larm.com
PICSN7
Phone: [phone] | [phone]
Email: [e-mail]
MiPA-U0405-NULQ_150806.docx
Also Available from SECO-LARM:
Camera will not turn on
Make sure that all wires are connected securely and
that the polarity is correct
No output power from power supply
Check to see that the main power cable is securely
connected to the AC wall socket
Make sure that the AC wall socket is powered
Check LED indicators on power supply to ensure
that input power is being received
Check the total supply current for all connected
device does not exceed 5A