ENFORCER SECO-LARM SLI ST-2406-3AEQ User manual

ST-2406-3AEQ
Power Supply/Charger with Enclosure
Manual
•
Automatic recharging of backup batteries
•Automatic switchover to backup battery if
main power is lost or cut
•Built-in battery short-circuit protection
•Low-battery cutoff
•LE s indicate power status
•Programmable C voltage output
•Regulated and filtered output voltage
•Fused output for a regulated charge
•
Heavy-duty steel case to protect power
connections
•Enclosure has space for up to two 4Ah
or one 7Ah backup batteries
•Includes battery leads for easy
installation
•High efficiency at full load
•Heat sink free design
Features:

ENFORCER Power Supply/Charger with Enclosure
2SECO-LARM U.S.A., Inc.
Parts List:
1x
Power supply/c
harger
unit
3x
Wire
leads
for backup battery
1
x
Flange n
ut
for wire relief clamp
1x
Wire
relief
clamp
2x
Screw
-
on
wire nuts
1x
Large grommet
1x
Small grommet
1x
Manual
Introduction:
D Voltage
6,12,24
Operating v
oltage
1
2
~24 VAC/V C for
6
V C
,
18~24 VAC/V C for
12V C
,
24~28 VAC or 26~28 V C for 24V C
Status
LEDs
A Input
Green
D Output
Red/Blue
(Blue indicates 24V)
urrent (
c
ontinuous)
2.5A
urrent (p
eak)
3.0A
urrent output (max.
c
harge)
6V=100mA, 12V=220mA, 24V=450mA
Maximum A i
nput
See Transformer Selection in Table 3, pg. 3
Master f
use
5A
Low battery cutoff
When battery voltage is
<20%
Operating temperature
-
4
°~149° F
(
-
20°~65° C)
Dimensions
Board
2
7
/
8
"x2
7
/
8
"x1
3
/
8
" (
73x73
x
35
mm)
Enclosure
10
"x
7
3
/
4
"x
3
1
/
2
" (
254
x
196
x
89
mm)
Specifications:
SECO
-
LARM’s
ST
-
2406
-
3AEQ power supply
/charger ensure
s
that alarm systems and access control
systems have enough power to do their job. Protected by fused battery outputs, input polarity protection
diodes, and backup battery polarity reverse protection, this power supply/charger can be used to maximize
the security and efficiency of nearly any alarm or access control installation. Enclosure has space for up to 2
backup batteries (leads included for one optional backup battery).
Overview
:
C Output LE
(red/blue)
1 2
ON
AC
– DC +
– BAT +
Class-
II
t
ransformer
VAC
input
Backup
battery
outputs
AC Input
LE
(green)
Master
fuse
Voltage selector
IP switch
Output voltage
trimpot
Alarm or a
ccess
control panel
V C output
1
2
O
N
AC
– DC +
– BAT +
Mounting holes
Mounting holes
Wire relief clamp
mounting screw
Knockout
(top, bottom,
both sides
and back)
Ventilation holes
(both sides)
Notes:
1. Other holes shown are for
transformer mounting
2. Bottom side includes two security
lock holes
Power Supply/Charger Enclosure (cover removed)
Front View Side View
AC power
input hole

ENFORCER Power Supply/Charger with Enclosure
SECO-LARM U.S.A., Inc. 3
1. Before connecting any external devices, temporarily power
up the unit and measure the C output voltage at the device
connection point to avoid damage to devices. If voltage drop
is large, adjust the voltage using the output voltage trimpot
(see Fig. 1). Then disconnect power before connecting
external devices.
2. See ST-2406 3EAQ LE status indicators in Table 3.
3. The ST-2406-3EAQ comes with a 5A fuse. Use only the
correct fuses to prevent short-circuits and damage to the
power supplies/chargers or the alarm access control panel.
4. The automatic low-battery cutoff will cut power when battery
voltage drops below 20% of the set output voltage.
Warning:
1. Installation and servicing must be performed by qualified service personnel.
2. The power supply must be installed in accordance with all national and local electrical codes.
3. o not use a higher AC input than recommended (rated max. 28VAC).
4. ISCONNECT THE POWER SUPPLY BEFORE CHANGING THE IP SWITCH SETTINGS OR
PERFORMING ANY TYPE OF SERVICE. There are no user serviceable parts inside.
5. o not touch any exposed metal parts, electrical, or electronic components as these parts may become
very hot under load.
6. Keep power-limited wiring separate from non power-
limited wiring (115VAC input, battery wires). Provide at
least 1/4” (7mm) spacing.
7. Connect the power supply/charger only to a rechargeable backup battery. Use of a non-rechargeable
backup battery could result in damage to the power supply/charger or the alarm access control panel.
1.
Mount the
power supply/charger enclosure
in the desired location
to be easily accessible for future servicing.
2. Set the desired C output voltage (6, 12, or 24V C) of the power
supply using the IP switch settings as shown in Table 1.
IMPORTANT: isconnect power before changing these IP switch
settings (Note the default voltage output setting is 12V C).
3. Connect a Class-II transformer with appropriate specifications (See
Table 2 right).
4. Connect a sealed lead-acid or gel-type backup battery if desired.
5. Connect the wires to their respective terminals (see "Overview,"
pg. 2 and “Notes” below). Use the supplied grommets to protect the
wires entering the enclosure and secure the AC power wire with the
wire relief clamp
and flange nut
.
Installation:
Table 1:
Voltage
SW1
SW2
6V
ON
ON
12V
ON
OFF
24V
OFF
OFF
Table 2:
6VD
ST
-
UV16
-
W50Q
16VAC/50VA
12VD
ST
-
UVDA
-
W100Q
24~28VAC/100VA
24VD
ST
-
UVDA
-
W100Q
24~28VAC/100VA
Notes:
Table 3
:
Green
LED
Red/Blue
LED
Status
ON
ON
*
Normal
OFF
ON
*
No VAC input
ON
OFF
No V C output
OFF
OFF
No VAC input and
no V C output
*Red=6,12V C, Blue=24V C
Fig. 1
Output voltage trimpot
Max.
Min.

ENFORCER Power Supply/Charger with Enclosure
4SECO-LARM U.S.A., Inc.
SECO
-
LARM
®
U.S.A., Inc.
16842
Millikan Avenue, Irvine, CA 92606
Website: www.seco
-
larm.com
Phone: (949) 261
-
2999 | (800) 662
-
0800
Email: sales@seco
-
larm.com
NOTI E
:
The SECO
-
LARM policy is one of continual development and improvement. For that reason, SECO
-
LARM
reserves the right to change specifications without notice. SECO-LARM is also not responsible for misprints. All trademarks
are the property of SECO-LARM U.S.A., Inc. or their respective owners. Copyright © 2018 SECO-LARM U.S.A., Inc. All
rights reserved.
®
PITSW1
76
3
-
187
%
MI_ST
-
2406
-
3AEQ_180620.docx
WARRANTY:
This SECO
-
LARM product is warranted against defects in material and workmanship while
used in normal
service for 1 (one) year from the date of sale to the original customer. SECO-LARM’s obligation is limited to the repair or
replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM. This Warranty is void if
damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or alteration,
improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment
is not operating properly as a result of causes other than defects in material and workmanship. The sole obligation of
SECO-LARM and the purchaser’s exclusive remedy, shall be limited to the replacement or repair only, at SECO-LARM’s
option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property
damage of any kind to the purchaser or anyone else.
Also Available from
SECO
-
LARM
®
:
12VD High
-
Amp
Switching TV
Power Supplies
Relay Boards Low Battery utoff
Power
Supply/ harger
Boards
P
C
-
U181
0
-
PULQ
shown
SR
-
2212
-
C5AQ shown
ST
-
B 01Q
S
T
-
2406
-
5AQ
shown
12VD Plug-In
A Adapters Power onverters Plug-and-Play Backup Batteries
Open-Frame
Transformers
ST
-
UV12
-
S1
.
0Q
shown
ST
-
LA130
-
TTQ
shown
SB
-
L10V1
-
20Q
shown
ST
-
UV A
-
W10
0Q
shown
No C output
•
Check whether the AC input voltage or backup battery voltage is
normal
Low C voltage output
•
Check whether the output voltage setting is correct
•Check whether the AC input wattage is correct (see chart, pg. 3)
•If the battery is supplying power, check whether the battery
voltage is normal
•Check whether the power supply board is overloaded
No backup battery power
•
Check whether the battery voltage is normal or already discharged
•Check whether the master fuse has burned out
Troubleshooting: