ENFORCER PA-U0405-NULQ User manual

ENFORCER 4-Channel CCTV “Brick” Power Supply
4SECO-LARM U.S.A., Inc.
Troubleshooting
:
CCTV
Power Supplies
Plug
-
in
AC Adapters
Plug
-
and
-
Play
Backup Batteries
(SB-P1012-26Q shown)
Voltage
Converters
PS-U1812-PULQ ST-UV12-S1.0Q
SB
-
L10V1
-
20Q /
SB-P1012-26Q ST-LA130-TTQ
N TICE
:
The inform tion nd specific tions printed in this m nu l re current t the time of public tion.
However, the
SECO-LARM policy is one of continu l development nd improvement. For this re son, SECO-
LARM reserves the right to
ch nge specific tions without notice. SECO-LARM is lso not responsible for misprints or typogr phic l errors.
Tr dem rks
re the property of SECO-LARM U.S.A., Inc. or their respective owners.
Copyright © 2014 SECO-LARM U.S.A., Inc. All rights reserved.
This m teri l m y not be reproduced or copied, in whole or
in p rt, without the written permission of SECO-LARM.
LIMITED
WARRANTY:
This SECO-
LARM product is w rr nted g inst defects in m teri l nd workm nship while
used in norm l service for two (2) ye rs from the d te of s le to the origin l customer. SECO-
LARM’s oblig tion is limited to
the rep ir or repl cement of ny defective p rt if the unit is returned, tr nsport tion prep id, to SECO-LARM.
This W rr nty
is void if d m ge is c used by or ttributed
to cts of God, physic l or electric l misuse or buse, neglect, rep ir or
lter tion, improper or bnorm l us ge, or f ulty inst ll tion, or if for ny other re son SECO-
LARM determines th t such
equipment is not oper ting properly s result of c uses other th n defects in m teri l nd workm nship.
The sole
oblig tion of SECO-
LARM nd the purch ser’s exclusive remedy, sh ll be limited to the repl cement or rep ir only, t
SECO-LARM’s option. In no event sh ll SECO-LARM be li ble for ny speci l, coll ter
l, incident l, or consequenti l
person l or property d m ge of ny kind to the purch ser or nyone else.
SECO
-
LARM
® U.S.A., Inc.
16842 Millik n Avenue, Irvine, CA 92606 Website: www.seco-l rm.com PICSN7
Phone: [phone] | [phone] Em il: s les@seco-l rm.com MiPA-U0405-NULQ_141013.docx
Also Available from SEC
-
LARM:
C mer will not turn on •M ke sure th t ll wires re connected securely nd th t
the pol rity is correct
No output power from power supply
•Check to see th t the m in power c ble is securely
connected to the power supply
•Check the tot l supply current for ll connected device
does not exceed 5A
PA-U0405-NULQ
4-Ch nnel CCTV “Brick” Power Supply
Manual

ENFORCER 4-Channel CCTV “Brick” Power Supply
2SECO-LARM U.S.A., Inc.
Features:
•
4-Ch nnel 5-Amp power distribution
•C n be mounted on br cket for e sy ccess nd reduced power cord clutter
•Univers l input volt ge: 100~240 VAC
•Adjust ble output volt ge: 12~13.8 VDC
•Built-in 6.8-Amp overcurrent protection.
•High volt ge nd over-current protection
•LED Power indic tor
Parts List:
•
Power supply x1
•Power c ble x1
Specifications:
Outputs
4
Tot l supply current
5A
M x. output power
60W
Over current protection
12VDC/6.8A
Output volt ge
12~13.8 VDC
Input fuse
3.15A@250VAC
Input
volt ge
100~240 VAC
Dimensions
5
7
/
8
”x2
3
/
16
”x1
5
/
16
” (150x55x33 mm)
Weight
13.4
-
oz (380g)
Oper ting temper ture
14°~113° F (
-
10°~45° C)
verview:
Introduc
tion:
T
he
PA
-
U0405
-
NULQ
is 4
-
ch nnel 5
-
Amp power supply. While norm lly used in CCTV
inst ll tions, it is suit ble for wide v riety of both CCTV nd ccess control pplic tions. It
fe tures djust ble output volt ge nd built-in 6.8-Amp overcurrent protection.
Top
Side
1
5
/
16
”
(33mm)
LED Indicator
Output terminals
Output voltage
potentiometer
5
7
/
8
” (150mm)
2
3
/
16
”
(55mm)
•
Mounting br cket x1
•Mounting screws x2
ENFORCER
®
ENFORCER 4-Channel CCTV “Brick” Power Supply
SECO-LARM U.S.A., Inc. 3
Installation:
1.
Find suit ble loc tion to inst ll the power supply. The power supply should be inst lled
out of sight, nd in pl ce protected from we ther nd high humidity. The power supply
must h ve dequ te ventil tion. Insufficient ventil tion m y c use overhe ting nd
d m ge could result.
2. Att ch the power supply to w ll or desk using the included mounting br cket. If
possible, mount the power supply sidew ys or with the termin ls f cing down so they do
not collect dust.
3. Connect the m in power c ble to the power supply.
Sample Installation:
Legend:
Positive (+):
Neg tive (–):
Wiring and Adjusting Voltage:
1.
Connect c mer s nd other devices to the power outputs, while observing correct
pol rity s shown in Figure 1. To minimize volt ge drop, use 18-g uge or l rger wire.
WARNING: Alw ys test output volt ge before connecting devices to the power supply.
2. If volt ge drop is l rge, djust the output volt ge potentiometer s shown in Figure 2.
Positive (+)
Neg tive (
–
)
Figure 1
ENFORCER
®
ENFORCER
®
ENFORCER
®
Figure 2
Min.
M x.