EnGenius EWS850-FIT User manual

EWS850-FIT
EWS850-FIT Quick Start Guide
Quick Start Guide
EnGenius Fit Wi-Fi 6 2×2 Outdoor Wireless
Access Point
Quick Start Guide
Introduction
This Quick Start Guide is designed to guide you through the
installation of the Fit 2x2 access point, model EWS850-FIT,
including hardware mounting and configuration.
FIT Bridge Outdoor
Access Point
Mounting
Screw Kit x2
Mounting
Bracket
Pole Mounting
Strap x2
Ground Wire &
Screw Set
Product CardDetachable Antena:
2.4GHz Antenna x2
5GHz Antenna x2
Package Contents
• Wi-Fi 6 technology for high-performance Wi-Fi in high-density,
multi-device environments.
• Two spatial streams support up to 1,200 Mbps (5GHz) & 574
Mbps (2.4GHz).
• Multiple applications for cloud and on premises solutions.
Model: EWS850-FIT
System Requirements
• Google Chrome (57.0.2987.110 and later)
• Microsoft Edge (80.0.361.103 and later)
• Mozilla Firefox (52.0 and later)
Web Browser

EWS850-FIT Quick Start Guide
Hardware Overview
Reset Button:
Reset to default: Press and hold the reset button on the PoE adaptor for over 60 seconds, and the LED (PWR)
will start Fast Flashing (0.2 sec). Then, the device will be reset to factory default settings.
Bottom Cover
(Aluminum
Die-Casting)
Mounting
Holes Detachable Antennas
(SMA Type)
Top Cover
(UL Certified Plastic)
LED
Indicaters
LAN- 2.5 Gigabit Ethernet Port
(802.3at PoE)
LEDs
STATUS LED COLOR LED BEHAVIOR
Connecting to the management
(FitXpress/FitController)
PWR (Orange) Flashing (0.5 Sec.)
Management Connected
(FitXpress/FitController/Standalone)
PWR (Orange) Solid On
LAN Connected LAN (1G) LAN (2.5G) Solid On
LAN Transmitting LAN (1G) LAN (2.5G) Flashing
2.4GHz Radio On 2.4GHz (Green) Solid On
2.4GHz Transmitting 2.4GHz (Green) Flashing
5GHz Radio On 5GHz (Green) Solid On
5GHz Transmitting 5GHz (Green) Flashing
Firmware Upgrading PWR LAN 2.4GHz 5GHz Flashing (0.5 Sec.)
Reset to Default PWR (Orange) Fast Flashing
AP Location Mode PWR LAN 2.4GHz 5GHz Flashing (1.5 Sec. on ->0.5 Sec. off)

EWS850-FIT Quick Start Guide
1. Determine where the Access Point will be placed and
mark the location on the surface for the two mounting
holes. Use the appropriate drill bit to drill two 8.1mm
diagram and 26mm-deep holes on the marks.
2. Screw the Anchors into the holes until they are flush
with the wall.
3. Fasten the Mounting Bracket with the included
Screws into the Anchors.
Hardware Mounting
Wall Mount
The access point can be mounted on the Wall and Pole, and
please perform the steps for the appropriate installation.
Anchors Wall
Screws
Anchors
Wall
4. Hang the Access Point against the wall on the
Mounting Bracket. 5. Secure the Access Point on the Mounting Bracket
with the secure lock on the side.
Mounting Bracket
Wall
FIT Bridge Outdoor
Access Point

EWS850-FIT Quick Start Guide
1. Thread the open end of the Pole Mounting Strap
through the two tabs on the Mounting Bracket.
Pole Mount
2. Lock and tighten the Pole Mounting Strap to secure
the Mounting Bracket onto the pole.
3. Hang the Access Point onto the Mounting Bracket.
4. Secure the Access Point on the Mounting Bracket with the secure lock on the side.
Pole Mounting
Strap
Mounting
Bracket
Mounting
Bracket
Pole Mounting
Strap

EWS850-FIT Quick Start Guide
EnGenius Fit AP devices can be powered by any of the following:
• EnGenius Fit PoE switches or 802.3af/ 802.3at PoE+ compliant switches
• EnGenius PoE Injector (EPA5006GR)
Caution: Do not use both power sources at the same time.
Powering EnGenius Fit AP
Connecting to a PoE Switch
Connect the Ethernet cable from the EnGenius Fit AP directly to the PoE port of the PoE switch.
EnGenius Fit
Access Point
Ethernet Cable
AP is power by a PoE Switch
EnGenius Fit
PoE Switch
Powering with a PoE Injector
(A) Connect one end of the Ethernet cable into the LAN (PoE) port of EnGenius FIT AP and the other end to the PoE port
on the PoE Adapter.
(B) Connect the power cord with the PoE Adapter and plug the other end into an electrical outlet.
(C) Connect the second Ethernet cable into the LAN port of the PoE Adapter and the other end to the Ethernet port to the
network.
Note: Please make sure to use Cat6 RJ45 Ethernet cables.
EnGenius Fit
Access Point
EnGenius
PoE Injectors
Gateway/Router/
Network Switch
(A)
(B)

EWS850-FIT Quick Start Guide
On-Premises Management
Management Plane
Cloud Management
EnGenius Fit provides flexible options to manage your devices based on your network planning and deployment.
Option A: Cloud Management
Option B: On-Premises Management
Option C: Standalone Configuration
Manage and monitor the Access Point through the FitXpress Platform with a mobile app or through the web portal.
FitXpress App (iOS/ Android)
If you want to manage the device in on-premises mode, you need an onsite management station running the FitController
connected to the same Layer 2 network.
FitController
FitController is a custom-built appliance with optimized network management software installed to ease onsite
deployment without manual server configurations.
Scan to download FitXpress app
Standalone Configuration
Using your computer, you can connect to the same network (subnet) as the Access Point and use the web browser to
access the device’s local web GUI page for configurations whenever the device is set to Standalone mode.
Download the FitXpress mobile app App Store click here
Download the FitXpress mobile app Google Play click here

EWS850-FIT Quick Start Guide
Option A: Cloud Management with FitXpress
Step 1: Connecting Ethernet
Connect the Ethernet cable from the EnGenius Fit AP directly to the
DHCP-enabled network and make sure the AP can reach the Internet.
Gateway/Router/ Network Switch
DHCP-Assigned IP EnGenius Fit
Access Point
Internet
Step 2: Register Device
You can register the access point with the FitXpress app.
1. Open the FitXpress mobile app and create an account.
2. Login and go to the Devices section. Click the Add (+) button.
3. Scan the QR code on the back of the device via the app.
Scan QR-code for device registration

EWS850-FIT Quick Start Guide
4. If the camera successfully scans the QR code, the app will display the device information. You can tap “Register” to
complete the registration.
Step 3: Connect to FitXpress
Once the device is powered on and ready to connect to the Internet, the PWR LED will stay Solid On, which means the
device is now connected to the FitXpress platform. It will automatically download the default configuration settings from
FitXpress for automated provisioning.
When the Access Point is connected to the FitXpress Platform for the first time, it will automatically check the latest
firmware version available. If a firmware upgrade is required, it might take 8~10 minutes to complete the process. All LED
indicators will be Flashing (0.5 sec) till the process is finished.
Step 4: Manage with the FitXpress
Log in to the FitXpress app to configure detailed settings and monitor your devices.

EWS850-FIT Quick Start Guide
EnGenius Fit
PoE Switch
Gateway
FitController EnGenius Fit
Access Point
Option B: On-premises Management with FitController
Step 1: Connecting Ethernet
Connect the Ethernet cable from the EnGenius Fit AP directly to the DHCP-enabled network, which is the same Layer-2
network as FitController.
Step 2: Log in to the FitController
Launch your web browser to access the login page of FitController and create an account. Enter the email address and
password that you created and click Sign In.
The FitController default IP address in DHCP client mode will get an IP address (e.g. X.X.X.X:8080) from the DHCP
server. If FitController cannot get an IP address from the DHCP server, the default IP address will be 192.168.1.250:8080.
Internet

EWS850-FIT Quick Start Guide
Step 5: Manage with FitController
Navigate to the left side menu to configure & manage your network and view network statistics using the FitController
management interface.
Step 4: Pairing the Device
1. Go to access point or switch list.
2. Select the newly added device and click “Pairing” to allow the access point to build an encrypted connection between
the device and FitController.
Step 3: Register Device and Assign to Network
1. Go to the system > Inventory page and click “Register Device (+)”.
2. FitController will list all EnGenius Fit devices discovered from the same L2 network in the Pending Approval section.
Select the device and Click “Register” to add to inventory. You can also tap “Manually” tab and register Fit device by
entering Serial Number.
3. From the Inventory page, Select the newly added device and click “Assign to Network” to add the device to your
personalized network.