Epson S5U1C88000H5 User manual

MF1272-03
CMOS 8-BIT SINGLE CHIP MICROCOMPUTER
(S1C88 Family In-Circuit Emulator)
S5U1C88000H5 Manual

NOTICE
No part of this material may be reproduced or duplicated in any form or by any means without the written permission of Seiko
Epson. Seiko Epson reserves the right to make changes to this material without notice. Seiko Epson does not assume any
liability of any kind arising out of any inaccuracies contained in this material or due to its application or use in any product or
circuit and, further, there is no representation that this material is applicable to products requiring high level reliability, such
as medical products. Moreover, no license to any intellectual property rights is granted by implication or otherwise, and there
is no representation or warranty that anything made in accordance with this material will be free from any patent or copyright
infringement of a third party. This material or portions thereof may contain technology or the subject relating to strategic
products under the control of the Foreign Exchange and Foreign Trade Law of Japan and may require an export license from
the Ministry of International Trade and Industry or other approval from another government agency.
Windows 95, Windows 98 and Windows NT are registered trademarks of Microsoft Corporation, U.S.A.
PC/AT and IBM are registered trademarks of International Business Machines Corporation, U.S.A.
All other product names mentioned herein are trademarks and/or registered trademarks of their respective owners.
© SEIKO EPSON CORPORATION 2001 All rights reserved.

The information of the product number change
Configuration of product number
Devices
Comparison table between new and previous number
S1C88 Family processors
Starting April 1, 2001, the product number has been changed as listed below. Please use the new
product number when you place an order. For further information, please contact Epson sales
representative.
S1 C 88104 F 0A01
Packing specification
Specification
Package (D: die form; F: QFP)
Model number
Model name (C: microcomputer, digital products)
Product classification (S1: semiconductor)
Development tools
S5U1 C 88348 D1 1
Packing specification
Version (1: Version 1 ∗2)
Tool type (D1: Development Tool ∗1)
Corresponding model number (88348: for S1C88348)
Tool classification (C: microcomputer use)
Product classification
(S5U1: development tool for semiconductor products)
∗1: For details about tool types, see the tables below. (In some manuals, tool types are represented by one digit.)
∗2: Actual versions are not written in the manuals.
Previous No.
E0C88104
E0C88112
E0C88308
E0C88316
E0C88317
E0C88348
E0C88P348
E0C88349
New No.
S1C88104
S1C88112
S1C88308
S1C88316
S1C88317
S1C88348
S1C8P348
S1C88349
Previous No.
E0C88365
E0C88F360
E0C88408
E0C88409
E0C88816
E0C88832
E0C88862
E0C88F816
New No.
S1C88365
S1C8F360
S1C88408
S1C88409
S1C88816
S1C88832
S1C88862
S1C8F816
Comparison table between new and previous number of development tools
Development tools for the S1C88 Family
Development tools for the S1C63/88 Family
Previous No.
88ISAIF
ADP88348
ADP88360
DEV88104
DEV88112
DEV88308
DEV88316
DEV88317
DEV88348
DEV88365
DEV88408
DEV88409
New No.
S5U1C88000H4
S5U1C88348X
S5U1C88360X
S5U1C88104D
S5U1C88112D
S5U1C88308D
S5U1C88316D
S5U1C88317D
S5U1C88348D
S5U1C88365D
S5U1C88408D
S5U1C88409D
Previous No.
DEV88816
DEV88832
DEV88862
DMT88348-DB
ICE88UR
PRC88316
PRC88348
PRC88365
PRC88409
PRC88816
SAP88
URS88348
New No.
S5U1C88816D
S5U1C88832D
S5U1C88862D
S5U1C88348T
S5U1C88000H5
S5U1C88316P
S5U1C88348P
S5U1C88365P
S5U1C88409P
S5U1C88816P
S5U1C88000S
S5U1C88348Y
Previous No.
ADS00002
GWH00002
URM00002
New No.
S5U1C88000X1
S5U1C88000W2
S5U1C88000W1
00
00

CONTENTS
S5U1C88000H5 EPSON i
(S1C88 FAMILY IN-CIRCUIT EMULATOR)
S5U1C88000H5 Manual (S1C88 Family In-Circuit Emulator)
This manual explains the use of the in-circuit emulator (S5U1C88000H5), setting up the system and
starting up the debugger.
For the functions and operations of the debugger, see the help topics displayed in the debugger.
See also the tool manuals below which are provided for each model.
- S5U1C88xxxP Manual
- S5U1C88xxxD Manual or S1C88 Family Development Tool Manual
CONTENTS
CHAPTER 1PREFACE ________________________________________________ 1
1.1 Outline...........................................................................................................1
1.2 Operating Environment ................................................................................ 1
CHAPTER 2 S5U1C88000H5 PACKAGE __________________________________ 2
2.1 Components ..................................................................................................2
2.2 Component Specifications ............................................................................ 2
CHAPTER 3IN-CIRCUIT EMULATOR (S5U1C88000H5) ______________________ 3
3.1 Outline...........................................................................................................3
3.2 Operating Environmental Conditions .......................................................... 3
3.3 Specifications of Operation Panel................................................................4
CHAPTER 4SETTING UPEQUIPMENT ____________________________________ 5
CHAPTER 5INSTALLING SOFTWARE ______________________________________ 6
CHAPTER 6OPERATION ______________________________________________ 8
6.1 Starting up S5U1C88000H5 for Windows 98............................................... 8
6.2 End Procedure .............................................................................................. 9
6.3 Initial Setup File (ICE88UR.INI) and Parameter File (.PAR) ..................... 9
6.4 Debugging.....................................................................................................9
CHAPTER 7PRECAUTIONS ____________________________________________ 10
APPENDIX LIST OF MENUS, SHORTCUT KEYS AND DEBUG COMMANDS ___________ 11

1 PREFACE
S5U1C88000H5 EPSON 1
(S1C88 FAMILY IN-CIRCUIT EMULATOR)
CHAPTER 1PREFACE
1.1 Outline
The S5U1C88000H5 package, one of the software development tool packages for the 8-bit single chip
microcomputer S1C88 Family, consists of an in-circuit emulator (S5U1C88000H5) and a debugger
(S5U1C88000H5 for Windows 98). It allows the programmer to efficiently debug the target system and the
target program.
This system can be used for all the S1C88 Family models. The S5U1C88000H5 in-circuit is compatible
with each model of the S1C88 Family by installing the Peripheral Circuit Board (S5U1C88xxxP) that is
provided for each model.
The S5U1C88000H5 system provides an advanced software developing environment that uses a personal
computer as the host computer.
ICE88UR
E0C88Family In-Circuit Emulator
Fig. 1.1.1 S5U1C88000H5 external view
1.2 Operating Environment
To construct an S5U1C88000H5 system, the following equipment is necessary in addition to this package:
Personal computer
- IBM-PC/AT or compatible model with Windows 98 installed.
- 80486DX2 66 MHz CPU or higher and 24MB RAM are recommended.
- A USB port is required in the personal computer.
- A hard disk drive, a 3.5" floppy disk drive (1.44MB) and a mouse are required.
Display unit
- A 16 or more color display.
- 1024 ×768 dot display is recommended.
Peripheral Circuit Board, other development tools
- Prepare the Peripheral Circuit Board and development tools (software) for the model to be developed.
Basic software
- The S5U1C88000H5 system is compatible with Windows 98 service pack 1 or Windows 98 SECOND
EDITION. Note that it is not guaranteed to work with other versions.
∗The name 'ICE88UR' on the development
tool is the old name of the product.

2 S5U1C88000H5 PACKAGE
2EPSON S5U1C88000H5
(S1C88 FAMILY IN-CIRCUIT EMULATOR)
CHAPTER 2 S5U1C88000H5 PACKAGE
2.1 Components
After unpacking the S5U1C88000H5 package, check to see that all the following components are included.
Figure 2.1.1 shows the package drawing.
• S5U1C88000H5 main unit
• AC adapter • USB interface cable
• AC cable
• Floppy disk
(3.5" 2HD, 1.44MB) • User registration card • Warranty card
Registration
..............
..........
............
........
• S5U1C88000H5 Manual
One each
for English and Japanese One each for English and Japanese
One
One
One
One
One each
for English and Japanese
DISK
POWER
EMU
SLP/HALT
RESET
TRGOUT
STOPOUT
TRCIN
BRKIN
GND
ICE88UR E0C88 Family In-Circuit Emulator
ON/OFF
DIAG
EPSON
CMOS 8-bit Microcomputer S1C88 Family
S5U1C88000H5 Manual
SEIKO EPSON CORPORATION
Fig. 2.1.1 S5U1C88000H5 package
2.2 Component Specifications
Table 2.2.1 shows the component specifications in the S5U1C88000H5 package.
Table 2.2.1 S5U1C88000H5 component specifications
Components
S5U1C88000H5
main unit
USB I/F cable
AC adapter
AC cable
Accessories
Package
Remarks
Rubber feet included
Peripheral Circuit board is sold separately
Rubber feet excluded
Outside: 5 V, Inside: 0 V
One each for English
and Japanese
Items
Dimensions
Weight
External color
Input voltage
Current consumption
Board mounted
Length
Dimensions
Input voltage
Input frequency
Power consumption
Output voltage/current
Length
Plug type
System disk
Manual
Warranty card
User registration card
Dimensions
Materials
Total weight of package
Specifications
270 (W) ×192 (D) ×79 (H) mm
Approx. 2.5 kg (main body)
Cygnus white
DC 5 V
2 A, max.
ICE board (one)
2 m
160 ×80 ×60 mm
AC 90 V to 264 V
47 Hz to 63 Hz
25 W, max. (in ICE system load)
DC 5 V/5 A, with overcurrent protection
1.8 m
Bipolar with ground
3.5" 2HD, 1.44MB (two)
S5U1C88000H5 Manual
380 (W) ×260 (D) ×225 (H)
W carton, cardboard
Approx. 4 kg

3 IN-CIRCUIT EMULATOR (S5U1C88000H5)
S5U1C88000H5 EPSON 3
(S1C88 FAMILY IN-CIRCUIT EMULATOR)
CHAPTER 3 I N -C IRCUIT E MULATOR (S5U1C88000H5)
3.1 Outline
The S5U1C88000H5 emulates the functions of the S1C88 core CPU and is used by installing a Peripheral
Circuit Board for each model. The S5U1C88000H5 is connected to a personal computer via the USB port.
The following shows the features of the S5U1C88000H5:
- Supports all the S1C88 Core CPU models
- 576KB of emulation memory built-in
- Advanced emulation functions (continuous execution, step execution, trace, break, coverage, etc...)
- On-the-fly function for real time monitoring memory.
See help topics of the debugger for details of the debugging functions.
Emulation Memory
The S5U1C88000H5 built-in emulation memory consists of the following two parts:
(1) 64KB emulation memory
This part corresponds to a 64KB area from address 000000H to address 00FFFFH in the accessible
memory space of the S1C88 core CPU.
(2) 512KB emulation memory
This part can be allocated to a 512KB area within address 010000H to address FFFFFFH. To allocate
the emulation memory to a 512KB area to be used, specify the address in a parameter file that is read
at the S5U1C88000H5 system start-up.
Thus the emulation memory can be used as an external memory that is generally prepared on the target
board if the capacity of the external memory is 512KB or less. It is especially useful for debugging sys-
tems that have ROMs as the external memories.
Further, external RAM on the target board can also be debugged like the emulation memory.
See the development tool manual of the model to be developed or the "S1C88 Family Development Tool
Manual" for specifying memory configuration.
3.2 Operating Environmental Conditions
Table 3.2.1 shows the environmental conditions that have to be used to operate the S5U1C88000H5.
Table 3.2.1 Environmental conditions
Remarks
No condensation
Items
Operating temperature
Storage temperature
Operating humidity
Storage humidity
Resistance to vibration
Specifications
5 to 40 °C
-10 to 60 °C
35 to 80%
20 to 90%
Operating: 0.25 m/S2
Transportation: 1 m/S2

3 IN-CIRCUIT EMULATOR (S5U1C88000H5)
4EPSON S5U1C88000H5
(S1C88 FAMILY IN-CIRCUIT EMULATOR)
3.3 Specifications of Operation Panel
Figure 3.3.1 shows the external view of the panels and Table 3.3.1 shows the function of each part of the panels.
Fig. 3.3.1 External view of S5U1C88000H5 panels
Table 3.3.1 Function list of operation parts
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Position
Side
Front
Front
Front
Front
Front
Front
Front
Front
Front
Front
Front
Back
Back
Function
The breaker cuts off the power of the S5U1C880000H5 system (ICE
board, Peripheral Circuit board and target board) at consumption
current of 4 A or more. A small staff of the breaker comes up at the
shut-off. The staff should be at the recessed position for normal
operating status. The breaker does not work at the normal operation.
Upon coincidence of trigger conditions with a tracing trigger point, a
pulse is output from this terminal.
When the S1C88 CPU is in HALT or SLEEP status, low level signal
is output from this terminal. This is used to measure execution rate
of the CPU. At the break mode, low level signal is also output.
Information is stored in the trace memory by connection with a
signal of the target system.
A running program enters in break status by input a low level signal
from the target system.
In case the above terminal is monitored with such an oscilloscope,
the GND line of the oscilloscope is connected to this terminal. This
is also used as a GND in case the signals are input to the above
terminals.
This green LED lights upon power-on of S5U1C880000H5.
This red LED lights when the target program is in running status.
This yellow LED lights when the S1C88 CPU stops executing the
program.
This switch reset S5U1C880000H5. (for maintenance)
Setting up when the S5U1C880000H5 power on, execute the self
diagnostic test or not
This is a connector to connect the USB interface cable.
This is a connector to connect the DC cable of the AC adapter
dedicated for S5U1C880000H5.
Turns the S5U1C880000H5 power on and off.
Indicated symbol
CB
TRGOUT
STOPOUT
TRCIN
BRKIN
GND
POWER
EMU
SLP/HLT
RESET
DIAG
DC 5V
POWER SW
Name
Circuit breaker
Tracing trigger output
terminal
HALT/SLEEP status
output terminal
Trace input terminal
Break input terminal
Ground terminal
for above
Power-on LED
Emulation LED
Halt LED
Reset switch
Diagnostic switch
Connector for connecting
USB interface cable
DC input connector
Power switch
Note: In case of change the mode by the diagnostic switch, be sure to shift it at power off the S5U1C88000H5.
POWER
CB
POWERSW
DC5VIN
EMU
SLP/HALT
RESET
TRGOUT
STOPOUT
TRCIN
BRKIN
GND
ICE88UR E0C88 Family In-Circuit Emulator
ON
OFF
7 8 2
14
1
13
345610 12119
ON/OFF
DIAG
Front
Front ←
Back
Side

4 SETTING UP EQUIPMENT
S5U1C88000H5 EPSON 5
(S1C88 FAMILY IN-CIRCUIT EMULATOR)
CHAPTER 4SETTING UPEQUIPMENT
Connect the equipment as shown in Figure 4.1.
Note: Be sure to turn all the system equipment off before installation and connection.
AC cable
USB I/F cable
Peripheral Circuit Board
Personal
computer
To DC 5V IN
AC adapter
POWER
EMU
SLP/HALT
RESET
TRGOUT
STOPOUT
TRCIN
BRKIN
GND
USB port
S5U1C88000H5
ON/OFF
DIAG
Fig. 4.1 Connection of S5U1C88000H5 system
(1) Installing the Peripheral Circuit Board
Install the Peripheral Circuit Board for the model to be developed to the S5U1C88000H5. The target
board is connected to the Peripheral Circuit Board. Refer to the Peripheral Circuit Board manual of
each model for how to install the Peripheral Circuit and target boards.
(2) Connecting the USB interface cable
Connect the S5U1C88000H5 to the personal computer using the USB interface cable supplied in this
package.
(3) Connecting the AC adapter
Be sure to use the AC adapter supplied in this package for supplying power to the S5U1C88000H5.
Connect the DC cord plug of the AC adapter to the DC 5V IN connector of the S5U1C88000H5. For the
AC adapter, connect the AC cable supplied in this package. Use the same ground line between the
S5U1C88000H5 and the host computer.
Note: Make sure that the equipment is installed and/or connected properly before turning the power on.
The USB interface cable can be hot plugged.

5 INSTALLING SOFTWARE
6EPSON S5U1C88000H5
(S1C88 FAMILY IN-CIRCUIT EMULATOR)
CHAPTER 5INSTALLING SOFTWARE
This package contains two 3.5" floppy disks (English and Japanese). Make backup copies before installing
the software.
!! Read the Readme.txt file recorded in the disk !!
The Readme.txt file contains precautions. Be sure to read it before installing the software.
To install the tools
The debugger software should be installed in the host computer’s hard disk using the dedicated
installer. Follow the installing procedure described below. The explanation uses mouse operation, i.e.
click, but key operation is also available. When using the keyboard, enter the underlined letter on the
buttons.
(1) Start Windows 98. If the OS is already active, close
active programs.
(2) Insert the supplied disk into the drive.
(3) Double-click Setup.exe.
Welcome
(4) Click on the [Next>] button to proceed.
Choose Destination Location
A dialog box for specifying the folder in which to install
the tools appears.
(5) If you do not wish to change the default settings,
simply click the [Next>] button to execute installa-
tion.
To install in another folder
Click [Browse...] to bring up the [Choose Folder]
dialog box. From this dialog box, enter the path or
select the folder in which to install the tools. Click the
[OK] button to finish folder selection and then click
the [Next>] button.

5 INSTALLING SOFTWARE
S5U1C88000H5 EPSON 7
(S1C88 FAMILY IN-CIRCUIT EMULATOR)
Select Program Folder
(6) Enter the desired program folder name and click the
[Next>] button. To use the default folder name, simply
click the [Next>] button.
The installer will start installing the tools.
Setup Complete
(7) Click [Finish] to terminate the installer.
Program menu
The folder of tools is registered to the program menu by the installer.
To end installation
All dialog boxes that appear during installation have a [Cancel] button. To prematurely terminate
installation, click [Cancel] in the dialog box when it is displayed.
To uninstall
To uninstall the installed tools, use "Add/Remove Programs" on the Control Panel.

6 OPERATION
8EPSON S5U1C88000H5
(S1C88 FAMILY IN-CIRCUIT EMULATOR)
CHAPTER 6OPERATION
6.1 Starting up S5U1C88000H5 forWindows 98
The following shows the start-up procedure of the S5U1C88000H5 system.
(1) Turn the S5U1C88000H5 in-circuit emulator on.
Note: •After connecting the S5U1C88000H5 system, make sure that the equipment is installed and
connected correctly before turning the power on.
•After the S5U1C88000H5 is turned off, do not turn the S5U1C88000H5 on for at least 10
seconds.It may cause a malfunction in the S5U1C88000H5.
The S5U1C88000H5 debugger checks the S5U1C88000H5 hardware and files required. The check result is
displayed in the [Command] window. If any error message appears and the debugger does not start up
normally, terminate the debugger (choose [Exit] command from the [File] menu), then check the follow-
ing points.
- Is the Peripheral Circuit Board installed in the S5U1C88000H5 properly?
- Is the S5U1C88000H5 connected to the personal computer with the USB interface cable properly?
- Is the S5U1C88000H5 turned on?
- Is the appropriate parameter file prepared? (see Section 6.3)
(2) To start up the debugger, select Ice88ur.exe from the
program menu.
The debugger window below is appeared.

6 OPERATION
S5U1C88000H5 EPSON 9
(S1C88 FAMILY IN-CIRCUIT EMULATOR)
6.2 End Procedure
To terminate S5U1C88000H5 for Windows 98, choose the [Exit] command from the [File] menu.
Do not turn the S5U1C88000H5 off until the debugger is terminated.
6.3 Initial Setup File (ICE88UR.INI) and Parameter File (.PAR)
The Ice88ur.ini file installed in the Windows 98 system folder (\windows) contains the following initial
setup information for the S5U1C88000H5 debugger.
Model=
A model name to be developed is specified. The model name described here will appear on the
S5U1C88000H5 status bar.
Example: Model=E0C88316
Path=
A parameter file is specified.
The parameter file (.PAR) contains the memory mapping information for the model to be developed and
information for allocating an external memory area to the S5U1C88000H5 emulation memory. It is read
into the debugger (S5U1C88000H5 for Windows 98) at start-up. The development tool package for each
model includes a parameter file that contains a basic memory configuration. It is necessary to customize
the contents if the system to be developed has an external memory. Refer to the development tool manual
of each model or the "S1C88 Family Development Tool Manual" for the contents of the parameter file and
how to customize it.
The installer in this package installs the parameter file "Default.par" for starting up the debugger in the
same folder as the debugger program and sets it as the default parameter file so that the debugger will
read the file at start-up. To set the debugger to read an actual parameter file used for development, it is
necessary to rewrite this Path= specification so that the necessary parameter file will be read in.
Example: Path=DEFAULT.PAR →Path=C:\E0C88\DEV88316\88316.PAR
When specifying a parameter file existing in the same folder as the debugger program (Ice88ur.exe),
rewrite the file name only. When specifying a parameter file existing in another folder, the path should be
described.
CCFile=
A command chain file is specified. When a command chain file name is entered here, the S5U1C88000H5
debugger will automatically execute the commands described in the specified file after it starts up. Use
the command chain file for the S5U1C88000H5 environment configuration and loading program and
option files after starting up.
Example: CCFile=C:\E0C88\DEV88316\test.com
When specifying a command chain file existing in the same folder as the debugger program (Ice88ur.exe),
rewrite the file name only. When specifying a command chain file existing in another folder, the path
should be described.
6.4 Debugging
To read a target program and to debug the program, choose the command from the menu, click the tool
bar button, or enter the debug command directly in the [Command] window.
See Help in the debugger for debugging functions, operations and details of the debug commands.
To open the help window, choose the [Index...] command from the [Help] menu. The contents of the help
topics appear. Clicking an underlined item jumps to the topic.

7 PRECAUTIONS
10 EPSON S5U1C88000H5
(S1C88 FAMILY IN-CIRCUIT EMULATOR)
CHAPTER 7PRECAUTIONS
(1)Connecting and disconnecting the equipment
Be sure to turn the personal computer and the S5U1C88000H5 off when installing the Peripheral
Circuit Board or connecting cables and disconnecting them. Otherwise, the internal circuits of the
equipment may be destroyed.
(2)Turning the power on and off
Do not turn the S5U1C88000H5 on for at least 10 seconds after it is turned off. Turning the power on
without the interval may result in abnormal operation of the S5U1C88000H5 or in the circuit breaker
cutting off. It may also cause a malfunction.
(3)Overcurrent protection
When the S5U1C88000H5 is turned on under the condition that VDD and VSS are short-circuited on the
target system, the AC adapter cuts off the output current due to the overcurrent protection function.
In this case, the Power LED on the S5U1C88000H5 does not light up.
3 A or a more steady-state current on the target system cuts off the circuit breaker of the
S5U1C88000H5.
(4)Difference between the emulation memory and the RAM in the actual IC
Both the S5U1C88000H5 emulation memory and the RAM in the actual IC are undefined at power-on.
The set values are not same, therefore be sure to initialize the memory with the program.
(5)Difference between memory operations by the debugging commands and memory
access by programs
Memory dump and other memory operations by the debugging commands use the firmware clock
(default: 4 MHz) in the S5U1C88000H5. Memory access by the target program uses an emulation clock
similar to the actual IC. Therefore, the read data may differ between the program and the debug
command when low-speed devices or devices that delay outputting data are used on the target board.
In such cases, use a low-frequency firmware clock set by the debugging command (CLK command).
(6)Setting up USB port
USB functions may be disabled in some personal computers by default. Make sure that the USB port
is enabled and setup the BIOS configuration of the personal computer if necessary.
Do not connect the plural S5U1C88000H5 to the USB port. One personal computer can be connected
only one S5U1C88000H5.

APPENDIX LIST OF MENUS, SHORTCUT KEYS AND DEBUG COMMANDS
S5U1C88000H5 EPSON 11
(S1C88 FAMILY IN-CIRCUIT EMULATOR)
Menu Shortcut key Button Function Command
[File] [Open...] Ctrl + O Loading program LF
[Save...] Ctrl + S Saving program SF
[Options...] Ctrl + Shift + O --- Loading options LO
[Symbol] --- --- Loading/saving symbols LS, SS
[Condition] --- --- Loading/saving conditions LC, SC
[Log...] Ctrl + L --- Logging LOG
[Exit] Alt + F4 --- Terminating debugger Q
[Edit] [Copy] Ctrl + C, Ctrl + INS --- Copy to clip board ---
[Paste] Ctrl + V, Shift + INS --- Paste from clip board ---
[Modify] [Assemble...] Ctrl + A --- Assembly A
[Edit...] Ctrl + E --- Editing memory contents E
[Fill...] Ctrl + F --- Filling memory area F
[Move...] --- --- Copy memory M
[Move to em...] --- --- Copy target memory to emulation memory MVE
[Register...] Ctrl + R Modifying registers R
[Search] [Data...] Shift + F3 --- Data search DS
[Symbol...] F3 --- Symbol search SYS
[Trace...] Ctrl + F3 --- Trace memory search TS
[View] [Source-Source level] Ctrl + 1 C source display SET
[Source-ASM Mix] Ctrl + 2 C source & disassembly display SET
[Source-ASM] Ctrl + 3 Disassembly display SET
[Dump...] Ctrl + D --- Memory dump D
[Trace...] Ctrl + T Trace data dump TD
[Coverage] --- --- Coverage display CV
[List...] Alt + F3 Specifying program display location LI
[Map] --- --- Memory mapping information display MA
[Run] [Go] F5 Program execution G
[Go from Reset] Shift + F5 Program execution after resetting G
[Go with Options...] Ctrl + F5 --- Program execution from specified location G
[Step Into] F8 Step into SI
[Step Over] F10 Step over SO
[Step Exit] Shift + F7 Step exit SE
[Animate-Step Into...] Alt + F8 --- Step into with step count SI
[Animate-Step Over...] Alt + F10 --- Step over with step count SI
APPENDIX LIST OF MENUS, SHORTCUT KEYS
AND DEBUG COMMANDS

APPENDIX LIST OF MENUS, SHORTCUT KEYS AND DEBUG COMMANDS
12 EPSON S5U1C88000H5
(S1C88 FAMILY IN-CIRCUIT EMULATOR)
Menu Shortcut key Button Function Command
[Break] [Full Area...] Shift + F9 --- Setting break points for full area BA, BAR
[1MB Area...] F9 Setting break points with area specification BP, BPR
[Sequence...] Ctrl + Shift + F9 --- Setting sequential break mode BAS
[Data...] Ctrl + F9 --- Setting data break condition BD, BDR
[List] Alt + F9 List of break conditions BL
[Data] [Symbol...] Shift + F2 Registering/deleting symbols SY, SYR
[Parallel Dump...] Ctrl + F2 Setting parallel dump points PD, PDR
[Watch...] F2 Setting watch points W, WR
[Tools] [Tool bar] --- --- Tool bar on/off ---
[Status bar] --- --- Status bar on/off ---
[Others] [Macro] --- --- Macro MC, MCR
[Stub] --- --- Stub STB, STBR
[Scope] --- --- Function name display SCP
[Calculation...] --- --- Calculation CAL
[Command Chain...] Ctrl + G Command chain COM
[Variables...] Ctrl + Shift + F2 --- Variable display VAR
[History...] Ctrl + H --- Command history ---
[Window] [Cascade] --- --- Arrangement of windows ---
[Tile Horizon] --- --- Arrangement of windows ---
[Tile Vertical] --- --- Arrangement of windows ---
[Arrange Icons] --- --- Arrangement of icons ---
[1 Source] Alt + 1 --- Opening [Source] window OW
[2 Dump] Alt + 2 --- Opening [Dump] window OW
[3 Register] Alt + 3 --- Opening [Register] window OW
[4 Parallel dump] Alt + 4 --- Opening [Parallel dump] window OW
[5 Local] Alt + 5 --- Opening [Local] window OW
[6 Watch] Alt + 6 --- Opening [Watch] window OW
[7 Break] Alt + 7 --- Opening [Break] window OW
[8 Trace] Alt + 8 --- Opening [Trace] window OW
[9 Coverage] Alt + 9 --- Opening [Coverage] window OW
[10 Map] Alt + 0 --- Opening [Map] window OW
[11 Search result] Alt + Shift + 1 --- Opening [Search result] window OW
[12 Stdout] Alt + Shift + 2 --- Opening [STDOUT] window OW
[Environment] [Clock Select...] Shift + F4 --- Clock selection CLK
[CPU Reset] Ctrl + I CPU reset RST
[Set...] F4 --- Environment settings SET
[Trace Mode] --- --- Setting trace mode TM
[Trace Trigger] --- --- Setting trace trigger point TP, TPR
[Help] [Index...] --- --- Contents of help ---
[Using Help...] --- --- How to use help ---
[About...] --- --- Version display
--- --- Esc Stop execution ---

AMERICA
EPSON ELECTRONICS AMERICA, INC.
- HEADQUARTERS -
1960 E. Grand Avenue
EI Segundo, CA 90245, U.S.A.
Phone: [phone] Fax: [phone]
- SALES OFFICES -
West
150 River Oaks Parkway
San Jose, CA 95134, U.S.A.
Phone: [phone] Fax: [phone]
Central
101 Virginia Street, Suite 290
Crystal Lake, IL 60014, U.S.A.
Phone: [phone] Fax: [phone]
Northeast
301 Edgewater Place, Suite 120
Wakefield, MA 01880, U.S.A.
Phone: [phone] Fax: [phone]
Southeast
3010 Royal Blvd. South, Suite 170
Alpharetta, GA 30005, U.S.A.
Phone: +1-877-EEA-0020 Fax: [phone]
EUROPE
EPSON EUROPE ELECTRONICS GmbH
- HEADQUARTERS -
Riesstrasse 15
80992 Munich, GERMANY
Phone: [phone] Fax: [phone]
SALES OFFICE
Altstadtstrasse 176
51379 Leverkusen, GERMANY
Phone: [phone] Fax: [phone]
UK BRANCH OFFICE
Unit 2.4, Doncastle House, Doncastle Road
Bracknell, Berkshire RG12 8PE, ENGLAND
Phone: [phone] Fax: [phone]
FRENCH BRANCH OFFICE
1 Avenue de l' Atlantique, LP 915 Les Conquerants
Z.A. de Courtaboeuf 2, F-91976 Les Ulis Cedex, FRANCE
Phone: [phone] Fax: [phone]
BARCELONA BRANCH OFFICE
Barcelona Design Center
Edificio Prima Sant Cugat
Avda. Alcalde Barrils num. 64-68
E-08190 Sant Cugat del Vallès, SPAIN
Phone: [phone] Fax: [phone]
ASIA
EPSON (CHINA) CO., LTD.
28F, Beijing Silver Tower 2# North RD DongSanHuan
ChaoYang District, Beijing, CHINA
Phone: [phone] Fax: [phone]
SHANGHAI BRANCH
4F, Bldg., 27, No. 69, Gui Jing Road
Caohejing, Shanghai, CHINA
Phone: [phone] Fax: [phone]
EPSON HONG KONG LTD.
20/F., Harbour Centre, 25 Harbour Road
Wanchai, Hong Kong
Phone: [phone] Fax: [phone]
Telex: 65542 EPSCO HX
EPSON TAIWAN TECHNOLOGY & TRADING LTD.
10F, No. 287, Nanking East Road, Sec. 3
Taipei
Phone: [phone] Fax: [phone]
Telex: 24444 EPSONTB
HSINCHU OFFICE
13F-3, No. 295, Kuang-Fu Road, Sec. 2
HsinChu 300
Phone: [phone] Fax: [phone]
EPSON SINGAPORE PTE., LTD.
No. 1 Temasek Avenue, #36-00
Millenia Tower, SINGAPORE 039192
Phone: [phone] Fax: [phone]
SEIKO EPSON CORPORATION KOREA OFFICE
50F, KLI 63 Bldg., 60 Yoido-dong
Youngdeungpo-Ku, Seoul, 150-763, KOREA
Phone: [phone] Fax: [phone]
SEIKO EPSON CORPORATION
ELECTRONIC DEVICES MARKETING DIVISION
Electronic Device Marketing Department
IC Marketing & Engineering Group
421-8, Hino, Hino-shi, Tokyo 191-8501, JAPAN
Phone: [phone] Fax: [phone]
ED International Marketing Department Europe & U.S.A.
421-8, Hino, Hino-shi, Tokyo 191-8501, JAPAN
Phone: [phone] Fax: [phone]
ED International Marketing Department Asia
421-8, Hino, Hino-shi, Tokyo 191-8501, JAPAN
Phone: [phone] Fax: [phone]
International Sales Operations

In pursuit of “Saving”Technology, Epson electronic devices.
Our lineup of semiconductors, liquid crystal displays and quartz devices
assists in creating the products of our customers’ dreams.
Epson IS energy savings.