Epson DisplayPort ELPIF03 User manual

EnglishFrançaisDeutschItalianoEspañol
中文
(
简体
)
中文
(
繁体
)
日本語
© 2019 Seiko Epson Corporation. All rights reserved.
Printed in China
User's Guide 3
Guide de lutilisateur 15
Bedienungsanleitung 27
Manuale dellutente 39
Manual de usuario 51
使用说明书 63
使用說明書 75
取扱説明書 87
Notices 98

3
EnglishFrançaisDeutschItalianoEspañol
中文
(
简体
)
中文
(
繁體
)
DisplayPort Interface Board ELPIF03
Included Items List
Check the following list to conrm that you have all of the supplied items. If by any
chance there is anything missing or damaged, please contact your dealer.
DisplayPort Interface Board User's Guide (this document)
* To install/remove the interface boards, you need a commercially available No. 2 cross-
head screwdriver.
Safety Instructions
Read this document and the User's Guide supplied with the projector carefully to use
this unit safely and correctly. To allow you to solve any issues or problems quickly, keep
this document close to hand.
So that you can use the product safely and correctly, symbols are used in this guide and
applied to the product to indicate possible harm to the user or to others and the risk
of damage to property. The symbols and their meaning are as follows. Make sure you
understand them properly before reading this guide.
Warning
This symbol indicates information that, if ignored, could pos-
sibly result in death or personal injury due to incorrect han-
dling.
Caution
This symbol indicates information that, if ignored, could possi-
bly result in personal injury or physical damage due to incor-
rect handling.

4
EnglishFrançaisDeutschItalianoEspañol
中文
(
简体
)
中文
(
繁體
)
Warning
•This is a class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
•Special techniques are required to install or remove this product, so make sure you
contact a specialist or your local dealer. Failure to do so may cause electric shock or
malfunctions to occur.
•Disconnect the power cord from the projector before installing/removing this prod-
uct to/from the projector.
Installing/removing the product while the power cord is connected may cause elec-
tric shock to occur.
•Do not use sprays that contain ammable gas to remove dust or lint from the prod-
uct. The high heat generated inside the projector may cause a re.
•Do not use or install in locations where it may be subject to water or rain, or high
humidity, such as outdoors, in a bathroom, or shower room, and so on. Otherwise, it
could cause a re or electric shock to occur.
•Do not place the product in a location subject to high levels of dust or humidity, or
in a location subject to smoke or steam such as on a work surface or near a humidi-
er. Otherwise, it could cause a re or electric shock to occur.
•Unless you are a qualied service technician, do not open the product's case unless
instructed to do so in the User's Guide. Never disassemble or remodel the product.
There are high-voltage components inside the product that could cause re, electric
shock, or an accident to occur.
•Do not place containers containing water or any chemical products and so on near
this product. If anything spills or enters the product, it could cause a re or electric
shock to occur.

5
EnglishFrançaisDeutschItalianoEspañol
中文
(
简体
)
中文
(
繁體
)
Caution
•Special techniques are required to install or remove this product, so make sure you
contact a specialist or your local dealer. Otherwise, unexpected malfunctions could
occur due to static electricity and so on.
•This product has been designed for exclusive use with Epson projectors. Before in-
stalling this product, check the projector's model number. If this product is installed
on anything except for the specied projector, it may cause damage to this product
or the projector.
•When installing/removing this product to/from the projector, be careful not to
injure yourself on the edge of the product or the edge of the slot.
•Do not use or store in places where the product might be subjected to high and
low extremes of temperature. Also, avoid any sudden changes in temperature.
•Do not store this product within reach of children. There is a risk of children swallow-
ing screws or them getting stuck in the throat. If any screws are swallowed acciden-
tally, contact a doctor immediately.
•Make sure that no dust or trash enters the slot when installing this product. If dust
or trash enters the projector, it could cause a malfunction.
•Do not touch the connectors on this product with your hands. If this product is
damaged by static electricity it will not operate correctly. Make sure you discharge
any static build up before handling this product.
•After removing this product from the projector, store it in an anti-static bag.
•When cleaning this product, do not use a wet cloth or solvents such as alcohol,
benzene, or thinner. Doing so could cause an electric shock or malfunction to occur.

6
EnglishFrançaisDeutschItalianoEspañol
中文
(
简体
)
中文
(
繁體
)
Part Names
Front
Name Function
A
DisplayPort1 In port Inputs signals for computers that support
DisplayPort.
B
DisplayPort2 In port
Rear
Name Function
A
Connector Connects to the projector's Slot ports.

7
EnglishFrançaisDeutschItalianoEspañol
中文
(
简体
)
中文
(
繁體
)
Installing and Removing the Interface Board
Procedures and illustrations may dier depending on the projector you are using. For
details, see the "User's Guide" supplied with the projector.
Installing
You can install boards in Slot1 or Slot2 on the projector.
A
Remove the slot cover.
Loosen the fixing screws (4 points) with a com-
mercially available No. 2 cross-head screwdriver,
and pull out the slot cover.
Store the removed slot cover in a safe place.
* The slot cover may not be attached depending
on the projector you are using.
Before replacing this product with another inter-
face board, make sure you remove the interface
board from the projector first.
➡P. 8 -“Removing”
B
Make sure the interface board is not at an
angle, and insert it straight into the slot.
Push the interface board firmly into the slot until
it is fully inserted.
* Tighten the xing screws evenly to
prevent the interface board from
tilting.
C
Tighten the xing screws (4 points) with a
commercially available No. 2 cross-head
screwdriver.
Caution
•Tighten the xing screws securely. If the in-
terface board is not xed securely in place,
the projector may malfunction.
•Do not use an electric screwdriver when
tightening the xing screws. Doing so
could damage the interface board.

8
EnglishFrançaisDeutschItalianoEspañol
中文
(
简体
)
中文
(
繁體
)
Removing
A
Loosen the xing screws (4 points) with a
commercially available No. 2 cross-head
screwdriver.
B
Grip the knob, and pull the interface board
straight out.
Caution
Make sure the slot cover or an interface
board is always installed in the slot. If dust or
trash enters the projector, it could cause a
malfunction.
When Images are not Displayed
•Make sure that the screws on the interface board are tightened securely.
•Make sure that the projector's [Video Terminal Settings] are correct. For details, see the
guides supplied with the projector.
•Check that the projector or the interface board is using the latest rmware version. For
inquiries, use the contact details provided in the guides supplied with the projector.

9
EnglishFrançaisDeutschItalianoEspañol
中文
(
简体
)
中文
(
繁體
)
Specications
For inquiries, use the contact details provided in the guides supplied with the projector.
When disposing of this product, be sure to follow local rules and regulations. When
using this product in a company, be sure to follow the company's disposal rules and
regulations.
Product name ELPIF03
External dimensions W 180
×H 23.5×D 133 mm (not including protruding parts)
Connection ports DisplayPort In port (×2) HDCP2.2 supported
Supported resolutions
WQXGA*, WQHD, QXGA, WUXGA*, 1920 ×1080, UXGA,
WSXGA+, SXGA+, SXGA, WXGA++, WXGA+, WXGA, XGA,
SVGA, VGA
4K (3840 x 2160, Dual Columns), 4K (3840 x 2160, Dual), 4K
(4096 x 2160, SMPTE), 4K (3840 x 2160), HDTV (1080i/1080p),
HDTV (720p), SDTV (576p), SDTV (480p)
Scanning frequency
(horizontal)
27 to 98/270 (kHz)
Scanning frequency
(vertical)
24 to 60/120 (Hz)
Dot clock frequency 25 to 297/1188 (MHz)
Power 17 Vdc, 0.7 A
Operating temperature
range
0 to +50 °C (no condensation)
Storage temperature
range
-10 to +60 °C (no condensation)
Mass Approx. 450 g
* Only compatible when a VESA CVT-RB (Reduced Blanking) signal is being input.
Supported resolutions may vary depending on your projector. For details, see the guides
supplied with the projector.
Trademarks
The DisplayPort Certied Logo and DisplayPort Icons are Registered Trademarks of the
Video Electronics Standards Association (VESA).
The word DisplayPort is a Registered Trademark of VESA in various countries around the
world.

10
EnglishFrançaisDeutschItalianoEspañol
中文
(
简体
)
中文
(
繁體
)
List of Safety Symbols
The following table lists the meaning of the safety symbols labeled on the equipment.
No. Symbol mark Approved
standards Meaning
1
IEC60417
No. 5007
"ON" (power)
To indicate connection to the mains.
2
IEC60417
No. 5008
"OFF" (power)
To indicate disconnection from the
mains.
3
IEC60417
No. 5009
Stand-by
To identify the switch or switch position
by means of which part of the equip-
ment is switched on in order to bring it
into the stand-by condition.
4
ISO7000
No. 0434B
IEC3864-B3.1
Caution
To identify general caution when using
the product.
5
IEC60417
No. 5041
Caution, hot surface
To indicate that the marked item can be
hot and should not be touched without
taking care.
6
IEC60417
No. 6042
ISO3864-B3.6
Caution, risk of electric shock
To identify equipment that has risk of
electric shock.
7
IEC60417
No. 5957
For indoor use only
To identify electrical equipment de-
signed primarily for indoor use.
8
IEC60417
No. 5926
Polarity of d.c. power connector
To identify the positive and negative
connections (the polarity) on a piece of
equipment to which a d.c. power supply
may be connected.