Epson S5U1C88000P User manual

MF1434-01
CMOS 8-BIT SINGLE CHIP MICROCOMPUTER
(S1C88 Family Peripheral Circuit Board)
S5U1C88000P Manual

NOTICE
No part of this material may be reproduced or duplicated in any form or by any means without the written permission of Seiko
Epson. Seiko Epson reserves the right to make changes to this material without notice. Seiko Epson does not assume any
liability of any kind arising out of any inaccuracies contained in this material or due to its application or use in any product or
circuit and, further, there is no representation that this material is applicable to products requiring high level reliability, such
as medical products. Moreover, no license to any intellectual property rights is granted by implication or otherwise, and there
is no representation or warranty that anything made in accordance with this material will be free from any patent or copyright
infringement of a third party. This material or portions thereof may contain technology or the subject relating to strategic
products under the control of the Foreign Exchange and Foreign Trade Law of Japan and may require an export license from
the Ministry of International Trade and Industry or other approval from another government agency.
© SEIKO EPSON CORPORATION 2001 All rights reserved.

New configuration of product number
Starting April 1, 2001, the product number has been changed as listed below. Please use the new
product number when you place an order. For further information, please contact Epson sales
representative.
Devices
S1 C 88104 F 0A01
Packing specification
Specification
Package (D: die form; F: QFP)
Model number
Model name (C: microcomputer, digital products)
Product classification (S1: semiconductor)
Development tools
S5U1 C 88348 D1 1
Packing specification
Version (1: Version 1)
Tool type (D1: Development Tool)
Corresponding model number (88348: for S1C88348)
Tool classification (C: microcomputer use)
Product classification
(S5U1: development tool for semiconductor products)
00
00

CONTENTS
S5U1C88000P MANUAL EPSON i
(S1C88 FAMILY PERIPHERAL CIRCUIT BOARD)
S5U1C88000P Manual (S1C88 Family Peripheral Circuit Board)
This manual describes how to use the S1C88 Family Peripheral Circuit Board (S5U1C88000P). This circuit
board is used to provide emulation functions when it is installed in the ICE (S5U1C88000H5), a debug-
ging tool for the 8-bit Single Chip Microcomputer S1C88 Family.
This manual describes only the common specifications of the S1C88 Family Peripheral Circuit Board
(S5U1C88000P), so refer to the S5U1C88000P manual (Peripheral Circuit Board for S1C88xxx) for the model
dependent specifications. For details on ICE functions and how to operate the debugger, refer to the
separately prepared manuals.
Contents
CHAPTER 1INTRODUCTION____________________________________________ 1
1.1 Outline of S5U1C88000P .............................................................................1
1.2 Components of S5U1C88000P .....................................................................1
1.3 External View of S5U1C88000P...................................................................1
CHAPTER 2SETTING UPTHE S5U1C88000P _____________________________ 2
2.1 Installing the S5U1C88000P in the ICE (S5U1C88000H5) .................................. 2
2.2 Downloading Cricuit Data .............................................................................3
CHAPTER 3PRODUCT SPECIFICATIONS ___________________________________ 4

CHAPTER 1: INTRODUCTION
S5U1C88000P MANUAL EPSON 1
(S1C88 FAMILY PERIPHERAL CIRCUIT BOARD)
CHAPTER 1INTRODUCTION
1.1 Outline of S5U1C88000P
The S5U1C88000P provides on a board all the peripheral circuits of S1C88 Family microcomputers other
than the core CPU. By installing this board in the ICE (S5U1C88000H5) you can use it to emulate each
model in the S1C88 Family. This board contains a programmable gate array (FPGA) and supports each
model by downloading the circuit data from the host PC to the FPGA via the ICE.
1.2 Components of S5U1C88000P
After unpacking your S5U1C88000P package, check to see that all of the following components are
included.
(1) S5U1C88000P main unit.............................................................................................. 1 board
(2) I/O cable (80-pin/40-pin ×2 flat type) .................................................................... 2 pairs
(3) Connector for connecting to target system (40-pin)............................................... 4 pieces
(4) Warranty card ............................................................................................................... 1 card
(5) User registration card .................................................................................................. 1 card
(6) Precautions on using the S5U1C88000P Peripheral Circuit Board ...................... 1 sheet
(7) S5U1C88000P Manual (S1C88 Family Peripheral Circuit Board) ........................ 1 copy
1.3 ExternalView of S5U1C88000P
Fig. 1.3.1 External view of S5U1C88000P
SW1
I/O #1 connector
I/O #2 connector

CHAPTER 2: SETTING UP THE S5U1C88000P
2EPSON S5U1C88000P MANUAL
(S1C88 FAMILY PERIPHERAL CIRCUIT BOARD)
CHAPTER 2SETTING UPTHE S5U1C88000P
2.1 Installing the S5U1C88000P in the ICE (S5U1C88000H5)
Insert this board along by the lower guide rail of the ICE (S5U1C88000H5). The system may fail to
operate if this board is not adequately mounted, so be sure to mount it securely.
Fig. 2.1.1 Installing the S5U1C88000P
∗ The name 'ICE88UR' on the development tool is
the old name of the product.

CHAPTER 2: SETTING UP THE S5U1C88000P
S5U1C88000P MANUAL EPSON 3
(S1C88 FAMILY PERIPHERAL CIRCUIT BOARD)
2.2 Downloading Circuit Data
This board (S5U1C88000P) comes with the FPGAthat contains factory inspection data, therefore the
circuit data for the model to be used should be downloaded. The following explains the downloading
procedure.
1) Set the switch "SW1"*1on this board to the "3" position.
2) Install this board to the ICE (S5U1C88000H5) as shown in Section 2.1.
3) Connect the ICE to the host PC. Then turn the host PC and ICE on.
4) Invoke the debugger included in the ICE or assembler package. For how to use the ICE and debugger,
refer to the manuals supplied with the ICE and assembler package.
5) Download the circuit data file (.mot) corresponding to the model by entering the following commands
in the command window.
>XFER (erase all)
>XFWR <file name> (download the specified file)*2
>XFCP <file name> (compare the specified file and downloaded data)
6) Terminate the debugger and then turn the ICE off.
7) Remove this board from the ICE and set the switch "SW1" on the board to the "1" position.
8) Install this board to the ICE again.
9) Turn the ICE on and invoke the debugger again. Debugging can be started here.
∗1 See Figure 1.3.1, "External view of S5U1C88000P", for the location of SW1.
∗2 The downloading takes about 5 minutes.

CHAPTER 3: PRODUCT SPECIFICATIONS
4EPSON S5U1C88000P MANUAL
(S1C88 FAMILY PERIPHERAL CIRCUIT BOARD)
CHAPTER 3PRODUCT SPECIFICATIONS
The specifications of the S5U1C88000P are listed below.
S5U1C88000P
Dimension: 247.5 mm (wide) ×165 mm (depth) ×44.6 mm (height)
Weight: Approx. 500 g
Power supply: DC 5 V ± 5%, less than 1 A (supplied from ICE main unit)
I/O connection cable (80-pin)
S5U1C88000P connector: KEL8830E-080-170L, or equivalent
Cable connector (80-pin): KEL8822E-080-171 ×1
Cable connector (40-pin): 3M7940-6500SC ×2 pairs
Cable: 40-pin flat cable ×2 pairs
Interface: CMOS interface (3.3 V)
Length: Approx. 40 cm
Monitor signal cable
S5U1C88000P connector: 3M7610-5002SC, or equivalent
Cable connector (10-pin): 3M7910-6500SC ×1
Interface: CMOS interface (3.3 V)
Length: Approx. 40 cm
Accessories
40-pin connector for connecting to target system:
3M3432-6002LCSC ×4