ERA Protect SALAPWHESSU User manual

Model: SALAPWHESSU
BATTERY OPERATED WIRELESS SIREN
1. OVERVIEW
The ERA Protect Siren is a battery operated wireless
Siren that works with the ERA Protect Alarm System.
The Siren is a visual deterrent and has flashing comfort
lights to show potential intruders that it is a live siren.
When the Alarm is triggered, the Siren will sound at
104dB and the strobe will flash.
2. GET TO KNOW YOUR
PRODUCT
1. Using the drilling template mark up the mounting holes
required to be drilled.
5. WIRELESS OUTDOOR
SIREN INSTALLATION
ERA Home Security Ltd.
Valiant Way, Wolverhampton,
West Midlands, WV9 5GB.
Email: [e-mail]
Web: www.eraprotect.com
CUSTOMER HELPLINE
0345 257 2500
3. INSTALLING AN
ACCESSORY
1.
2.
3.
Add Device to app.
Place the protect tamper sleeve provided over the
tamper switch at the back of the siren before installing
onto the wall.
Place in required position.
The Tamper function is disabled for 15 minutes after
power up to allow for installation. After 15 minutes the
Tamper will become enabled, if the siren is removed from
its position after this point the alarm and siren will be
triggered.
Note: Accessory Tamper Switch is disabled to allow easy
installation.
Once your hub is set up you will be taken to your Protect
home screen.
To add a device press the Add ( + ) button in the top right
hand corner and select Add Device.
Follow the on-screen instructions to add your device. Repeat
as necessary for each device you would like to add. You can
add sensors in any order.
Once all devices have been added please check the Protect
Hub settings page, accessible via the side bar menu ( ), to
ensure all devices are listed and displayed correctly.
4. ADD DEVICES
INSTALLATION AND
OPERATING MANUAL
Cover Screw
Front Cover Screw
Bayonet
Comfort
LEDs
ABS Plastic Feet
2. Drill the marked holes where you will place your wall
plugs.
Tamper
Reset
Button
4.

ERA Home Security Ltd.
Valiant Way, Wolverhampton,
West Midlands, WV9 5GB.
Email: [e-mail]
Web: www.eraprotect.com
9. SPECIFICATION
CUSTOMER HELPLINE
0345 257 2500
Alarm Decibel:
Static Current:
Alarm Current:
Emitting Distance:
Frequency:
Battery:
Battery Life:
IP Rating:
Housing Material:
Size (LxWxH):
104dB
≤1mA
≤300mA
200m (in the open air)
868MHZ
Battery DC 3.6V (2 x ER34615
Lithium Batteries)
4 years
IP55
ABS Plastic
250 x 242.7 x 64mm
7. BATTERY
REPLACEMENT
When the panel receives the low battery report from the
siren, please change the battery.
1. Go into the Alarm Settings and switch Accessory
Tamper switch o.
Go to the location of the Siren and remove the cover
screw using a screwdriver.
Remove the front cover, then proceed to remove the
battery cover.
Unplug the battery connectors and remove from the
battery compartment.
Replace with new recommended batteries and plug
them into the Siren.
Apply the battery cover to the backplate and then
replace the front cover back to the backplate.
Go back into Alarm settings and switch Accessory
Tamper Switch back on.
3.
4. Take the backplate of the Siren, three screws, wall
plugs and a screwdriver to the location.
5. Push the wall plugs into the holes and proceed to
screw the backplate onto the wall using the
screws provided.
6. Remove the battery cover and attach the connectors.
9. Screw the cover screw at the bottom of the Siren
lens with a screwdriver to fix the cover to the
backplate.
4.
5.
6.
7.
2.
Note: Battery is required to be connected before use.
3. Remove the front cover.
7. Place the battery cover onto the backplate and screw
it securely.
Align the front cover to the backplate, hang and
slide down.
8.