ERA miGuard A105 User manual

Congratulations on your purchase of the miGuard A105 Wireless
plug-in Starter Alarm System.
Before you commence installation we recommend that you unpack
the product, familiarise yourself with the component parts, and
carefully read through this instruction guide.
There are some parts of the installation that must be completed in
the order shown to ensure successful installation.

Table of Contents
Features
Kit Contents & System Overview
Control Unit Operation
Control Unit (CU)
Power On
Power Off
Beeps & Strobe Light
Setting Entry & Exit Delays
Connecting & Deleting Accessories
Pairing a Remote Control
Pairing a Door/Window Sensor
Pairing a PIR Motion Sensor
Deleting Accessories
Grouping Sensors
Sensor Placement
Remote Control
Overview
Arm
Disarm
Part-Arm
Mute Operation
SOS
Nightlight on / off
1
2-3
4-5
6
7 –11
12 –15

Table of Contents continued
PIR Motion Sensor
Overview
PCB Layout
Working Mode
Test Mode
Power Saving Mode
Detection Scope
Test
Installation
Installation Tips
When used as an Accessory Kit
Technical Specifications
20 - 27
28 –29
30 - 33

Features
Quick & easy set-up, straight from the box
Works as a stand-alone alarm or can be used with any
miGuard alarm system
Strobe light and 90dB volume to deter intruders
Handy night light
Pet Friendly PIR Motion Sensor
PIR detection coverage 8m / 110field of view
The Door/window Sensor is ideal for entry and exit routes
The remote control includes arm, disarm, part-arm and
SOS panic buttons
Mute arm/disarm
Built-in back-up battery
Supports up to 40 wireless accessories
1

Kit Contents & System Overview
Control Unit (CU) x 1
The CU plugs directly into a suitable mains
power socket.
When an accessory is triggered, the built-in
siren will sound and the strobe light will flash
to alert you of intrusion into the protected area
and deter intruders.
Pet Friendly PIR Motion Sensor x 1
The Sensor incorporates fuzzy logic to minimize
false alarms from unwanted heat sources. With
the power saving feature, the Sensor will enter
into sleep mode after the second activation within
a 3 minute period, thereby saving power.
The Sensor features pet immunity for small
animals up to 25 kgs.

Wireless Door/Window Sensor x 1
The Door/Window Sensor can be fitted to doors, windows
and any other objects that open and close. The Contact
transmits signals to the Control Unit when the Magnet
mounted adjacent to the Contact is moved away.
Contact Magnet
Keyfob Remote Control x 2
The Remote Control is compact and includes a clip for
attaching to a key-chain/fob. The Remote Control is used
to arm, disarm and part-arm the system, and also to trigger
an emergency alarm (SOS).

PIR Motion Sensor Bracket x 1 Double-sided tape for
Door/Window Sensor x 2
User Manual x 1 Screws and Wall Plugs x 3
3

Control Unit Operation
Control Unit (CU)
Power/Learn Button Strobe Light
Power On
The Control Unit is set to ‘off’ by default.
To enable the Control Unit, plug the unit into a suitable power outlet and
press the power/learn button, it will beep once indicating that it is enabled.

Power Off
To turn the Control Unit ‘off’ press the power button once. Then press and hold
the power button for 6 seconds until a beep is heard, indicating that the Control
Unit is ‘off’.
Beeps and Strobe Light
Status
Control Unit
Strobe Light
Arm or Home Arm
Beeps Once
Comes On and Stays On
Disarm
Beeps twice
Flashes Twice, then Off
4

Mute Arm
No Beep
Lights Up
Mute Disarm
No Beep
Light Goes Off
5

Setting Entry and Exit Delays
The Sensors should be set in single delay zone before using this function.
Please refer to ‘Grouping Sensors’ on page 10.
Entry Delay (Alarm Delay)
When the Sensors which have been set to single delay zone are triggered, the
Control Unit will alarm after the delay time. If the Sensors that are set to normal
zone or home mode zone are triggered, the Control Unit will alarm immediately.
Press the connect button twice = 15 second delay
Press the connect button three times = 30 second delay
Press the connect button four times = function disabled
Note: Press the button on the Remote Control twice, the system switches to armed
status immediately. For single delay, refer to page 10.
Exit Delay (Arm Delay)

The whole alarm system enters armed status after the delay time.
6

Connecting and Deleting Accessories
Accessories need to be paired to the Control Unit so that it can receive signals
from them, and sound the alarm. The kit accessories are pre-learnt to the
Control Unit and are ready for use. If the Control Unit does not sound when
the Sensors are triggered, please pair them again. Accessories purchased
separately must be paired to the Control Unit before use.
Pairing a Remote Control
(1) Press the power/learn button on the Control Unit
The Control Unit will beep once, 3 seconds later it will beep once again and
the strobe will flash, the Control Unit is now ready for pairing.
(2) Press any button on the Remote Control
Press any button on the Remote Control, the Control Unit will beep once
indicating successful pairing.

Note: if the Control Unit beeps twice, it indicates that the Remote Control has been paired before.
7
2

Pairing a Door/Window Sensor
(1) Press the power/learn button on the Control Unit
The Control Unit will beep once, 3 seconds later it will beep once again and
the strobe will flash, the Control Unit is now ready for pairing.
(2) Separate the Transmitter and Magnet
Make sure that the triangle marks on the Transmitter and Magnet are facing
each other and less than 1cm apart, then separate them to more than 2cm
apart. The Control Unit will beep once to indicate successful pairing.
Note: if the Control Unit beeps twice, it indicates that the Door/Window Sensor has been paired
before.
< 1cm
8

Pairing a PIR Motion Sensor
(1) Press the power/learn button on the Control Unit
The Control Unit will beep once, 3 seconds later it will beep once again and
the strobe will flash, the Control Unit is now ready for pairing.
(2) Press the test button on the PIR Motion Sensor
Press the test button at the back of the PIR Motion Sensor. The Control Unit
will beep once, indicating successful pairing.
Note: if the Control Unit beeps twice, it indicates that the PIR Motion Sensor has been paired before.
Deleting Accessories

To disconnect accessories from the Control Unit, press and hold the
power/learn button on the Control Unit for 6 seconds. The Control Unit will
beep once and the strobe flash twice, indicating that all the accessories have
been deleted
9