Interlogix ATS125 Operating instructions

ATS125x/1260 Four-
Door/Four-Lift DGP
Programming Guide
P/N 1044982 (EN) • REV B • ISS 21JUN17

Copyright
© 2017 UTC Fire & Security Americas Corporation, Inc.. All rights
reserved.
Trademarks and
patents
Interlogix, ATS125x/1260 Four-Door/Four-Lift DGP name and logo
are trademarks of UTC Fire & Security.
Other trade names used in this document may be trademarks or
registered trademarks of the manufacturers or vendors of the
respective products.
Manufacturer
UTC Fire & Security Americas Corporation, Inc.
3211 Progress Drive, Lincolnton, NC, 28092, USA
Authorized EU manufacturing representative:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, Netherlands
Warnings and
Disclaimers
These products are intended for sale to, and installation by, an
experienced security professional. UTC Fire & Security cannot
provide any assurance that any person or entity buying its products,
including any “authorized dealer,” is properly trained or experienced
to correctly install security related products.
For more information on product warnings, refer to
www.utcfssecurityproducts.eu/productwarning/ or scan the code.
Version
This document applies to the product firmware version 2.13.
Certification
European Union
directives
UTC Fire & Security hereby declares that this device is in
compliance with the applicable requirements and provisions of the
Directive 2014/30/EU and/or 2014/35/EU. For more information see
www.utcfireandsecurity.com or www.interlogix.com.
2012/19/EU (WEEE directive): Products marked with this symbol
cannot be disposed of as unsorted municipal waste in the European
Union. For proper recycling, return this product to your local supplier
upon the purchase of equivalent new equipment, or dispose of it at
designated collection points. For more information see:
www.utcfssecurityproducts.eu/recycle/
Contact information
www.utcfireandsecurity.com or www.interlogix.com
Customer support
www.utcfssecurityproducts.eu

ATS125x/1260 Four-Door/Four-Lift DGP Programming Guide i
Content
Important information iii
Programming sequence 1
Minimal set-up 1
Basic set-up 2
Advanced settings 4
How to program the options 6
Accessing the installer programming menu 6
Programming the menu options 7
Accessing the door/lift programming menu 9
How to access the door / lift programming menu 9
1-DGP options 10
2-Door / Lift options 16
Access options 16
Request To Exit options 23
Alarm control 25
Reader options 27
Hardware options 33
Lift options 36
3-Initialise database 40
4-Display card 41
5-Door groups 42
6-Floor groups 43
7-System Options 44
8-Macro logic 45
9-Version number 47
10-To Local Devices 48
Reader and interface type programming 49
Short list of available zones and outputs per DGP address 50
Door/lift data hardware defaults 51
Hardware options: default zone/output number assignments 51

ii ATS125x/1260 Four-Door/Four-Lift DGP Programming Guide
Macro event flags 52
List of predefined event flags 52
Programming sheet: DGP options 56
Programming sheet: Door options 57
Programming sheet: Macro logic 60
Glossary 61
Index 65
Programming map 69

ATS125x/1260 Four-Door/Four-Lift DGP Programming Guide iii
Important information
This manual provides detailed explanations for programming the ATS125x/1260
and includes detailed explanations for the entire door / lift menus. All references
to the programming menus, and their numbers, are menus within programming
Remote Devices, Installer menu 28, and Titan Advisor Master > To Remote
Devices > DGP.
When installing a new 4-Door/4-Lift DGP, it is strongly recommended that you
first initialise the ATS125x/1260 using Menu 3 - Initialise Database. This step
may only be accomplished by programming using a RAS on the system databus
of the Advisor Master. It will set all programming to factory default; as listed in
this programming manual. Once initialised, the DGP may be programmed using
a RAS or a PC running TITAN software.
The ATS1250 and ATS1260 are the same physical products except for the
firmware (software) EPROM. The factory defaults are different for each product
and are listed in the programming sheets in this guide.
Whenever the ATS125x is mentioned, ATS1250, ATS1251, ATS1252, ATS1253,
ATS1254, and ATS1260 are included except where explicitly stated.

iv ATS125x/1260 Four-Door/Four-Lift DGP Programming Guide

ATS125x/1260 Four-Door/Four-Lift DGP Programming Guide 1
Programming sequence
The ATS125x/1260 four-door/four-lift DGP is a versatile access control panel to
extend the Advisor Master system with advanced access control functions. When
programming it is easy to lose track if one does not use a good method. Using a
good method also provides for an efficient way of programming.
Minimal set-up
The minimal set-up only consists of settings required to enable cards being read
and door opening due to a valid card.
1. Set the DGP address for the four-door/four-lift DGP (1 to 12 available).
2. Check if the RAM memory in ATS125x/1260 and the Advisor Master control
panel is the same.
3. Set addresses of RASes (readers or DGPs connected to the local databus of
the four-door/four-lift DGP.
4. In the Advisor Master control panel, installer programming (menu 19):
- In the Advisor Master control panel menu 4. DGP, activate polling for the
four-door/four-lift DGP and set the DGP type.
- Check and note in the Advisor Master control panel, menu 7. System
options the settings for Dual zone and the Number of prefix digits.
- In menu 13. Timezones, program timezones required for access control
functions (Request To Exit, Override timezone and Door groups).
- In menu 2, Area database, determine which areas will inhibit Request to Exit
or will inhibit access through a door when the areas are armed.
5. Go to menu 28, To remote devices. Select type 1 (DGP) and press [ENTER].
Enter the DGP address and press [ENTER]. You now are in the four-
door/four-lift programming menu.
6. Go to menu 1-DGP options.
Set or select the following options:
- Enter the required Batch Number (range 1 to 40). If card numbers or system
codes are unknown, then first see “Finding system codes for cards” on page
5.
- Enter Alarm Code Prefix Digits (same as in control panel).
- Enter RASes to be polled connected to the local databus.
- Enter LCD RAS connected to the local databus.
- Set Dual zone to the same setting as used in the control panel.
- Enter Re-lock delay time.
7. Go to menu 2-Door / Lift options.
8. Select the door to program. Only doors available on the selected DGP can be
entered.

2 ATS125x/1260 Four-Door/Four-Lift DGP Programming Guide
9. Move to menu Reader options.
10.Select the required Card format.
11.Press [ENTER] until the display indicates menu Hardware options.
12.Press 0 [ENTER] [ENTER] to leave menu 2-Door / Lift options
13.Move to menu 4-Display card and badge a number of cards to verify the
cards are being read, the card number is known.
14.Proceed with the basic set-up.
Basic set-up
1. Set the DGP address for the four-door/four-lift DGP (1 to 12 available).
2. Check if the RAM memory in ATS125x/1260 and the Advisor Master control
panel is the same.
3. Set addresses of RAS's (readers or DGP's connected to the local databus of
the four-door/four-lift DGP.
4. In the Advisor Master control panel, installer programming (menu 19):
- In the Advisor Master control panel menu 4. DGP, activate polling for the
four-door/four-lift DGP and set the DGP type.
- Check and note in the Advisor Master control panel, menu 7. system options
the settings for Dual zone and the Number of prefix digits.
- In menu 13. Timezones, program timezones required for access control
functions (Request To Exit, Override timezone and Door groups)
- In menu 2, Area database, determine which area/s will inhibit Request to
Exit or will inhibit access through a door when the area/s are armed.
5. Go to menu 28, To remote devices. Select type 1 (DGP) and press [ENTER].
Enter the DGP address and press [ENTER]. You now are in the four-
door/four-lift programming menu.
6. Go to menu 1-DGP options.
Set or select the following options:
- Number of Output controllers.
- Enter the required Batch Number (range 1 to 40). If card numbers or system
codes are unknown, then first see Finding system codes for cards (page 5).
- Alarm Code Prefix Digits (same as in control panel).
- Enter RASes to be polled connected to the local databus.
- Enter LCD RAS connected to the local databus.
- Enter RASes with RTE enabled that are connected to the local databus.
- Enter DGP to be polled connected to the local databus.
- Set Dual zone to the same setting as used in the control panel.
- Enter the Card to PIN time (only if Card & PIN required).
- Enter Two cards time (only if required).
- Enter Multiple Badge time (only if alarm control is required).

ATS125x/1260 Four-Door/Four-Lift DGP Programming Guide 3
- Enter Re-lock delay time.
- Enter Region count limit (only if anti-passback is used).
7. Go to menu 2-Door / Lift options.
8. Select the door to program. Only doors available on the selected DGP can be
entered.
9. Now the first menu will be visible, Access options.
Set or select the following options:
- Select the door to program
- Unlock time
- Extended unlock time (if required)
- Shunting option (if required)
- Shunt time (if required)
- Extended shunt time (if required)
- Shunt warning time (if required)
- Shunt until door has closed
- Cancel shunt time after door closed
- Low security timezone (if required)
- IN / OUT reader requires card and PIN
- IN / OUT reader inhibit PIN if timezone
- IN / OUT reader inhibit region 0 user
- Anti-passback option (if required)
- IN / OUT reader region (if required)
- IN / OUT reader Two Cards function
10.Move to menu Request To Exit options (only if required)
Set or select the following options:
- Request To Exit Timezone
- IN or OUT RTE disabled if area is armed
- Request To Exit control
- Request To Exit reporting
11.Move to menu Reader options
Set or select the following options:
- Card format
- Zone holds door unlocked
- Door unlocked until door open
- Unlocked timezone (if required)
- Unlocked timezone after entry
- Report when door closed and locked
- Report open/unlocked as unlocked
- Report door open / close
- Report forced door
- Report DOTL
- Reader LED options
- Pulsed lock and unlock
- Disable Duress functionality

4 ATS125x/1260 Four-Door/Four-Lift DGP Programming Guide
12.Move to menu Hardware options.
Set or select the following options:
- Unlock output number
- Zone number
- Monitor second door zone (if required)
- Forced output number (if required)
- Shunt zone numbers (if required)
- Warning output number (if required)
- DOTL zone number (if required)
- DOTL output number (if required)
- Request To Exit zone number (if required)
- Interlock zone numbers (if required)
- Areas assigned to door (if required)
- Alarm output number (if required)
13.When out of the Hardware options, press 0 [ENTER] to leave the menus in
Door options. Press [ENTER] again to leave the Door options. Press 0
[ENTER] again to leave the four-door/four-lift programming menu.
14.Set-up the required door groups in the Advisor Master user program
(menu 20)
15.Program users that require access control functions (door group)
16.Program zones available on the 4-Door DGP
Advanced settings
Add alarm control functions
In the Advisor Master installer programming:
•Program timezones required for alarm control functions (used in alarm
groups)
•Program alarm groups (if required) for access control functions
In the four-door/four-lift programming menu:
•Select menu 2-Door / Lift options and select the door to program
•Move to menu Alarm control
•Enter the required Alarm group
•Select the required Alarm control
•Select if Entry or Exit denied if area armed
•Select the Authorised RAS on the system databus (if required)
Assign the alarm groups to users that should have alarm control.