Honeywell Fire-Lite Alarms ANN-80 Series Technical manual

One Fire-Lite Place
Northford, CT 06472-1653 USA
203-484-7161 • FAX [phone]
www.firelite.com
ANN-80 Series
Product Installation Document
PN 52749:D1 8/17/10 10-490
The ANN-80 Series Remote Fire Annunciators and Indi-
cators (ANN-80, ANN-80-W, ANN-80C) are compact,
backlit LCD displays designed for use with compatible
FACPs Fire Alarm Control Panels. The displays mimic
the FACP display and are capable of displaying English-
language text of system point status including device type,
independent point alarm, trouble or supervisory zone and
custom alpha labels programmed into the FACP. Refer to
the FACP manual installation section for detailed system
information and wiring.
NOTE: Installation and wiring must be done in
accordance with NFPA 72 and local ordinances.
Specifications
TB1 Terminals 1 & 2
Operating Voltage Range: 18 VDC to 28 VDC
Current Consumption @ 24 VDC nominal (filtered and
nonresettable):
• Normal/Standby (no activity): 37.0 mA
• Trouble Condition: 39.0 mA
• Alarm: 40.0 mA
• AC Fail (not backlit): 15.0 mA
TB1 Terminals 3 & 4
ANN-BUS rated at 5.5 VDC and 60 mA max.
Dimensions
6 7/8”W x 5 3/8”H x 1 3/8”D
Mounting
The ANN-80 Series plastic enclosures can be surface or
semi-flush mounted in a single, double or 4” square elec-
trical box.
To mount the ANN-80 Series enclosure:
1. Open the ANN-80 Series cover by turning the key
switch counterclockwise to the ON (Unlocked)
position.
2. Push in the snap latch tab located on the right side
while pulling the cover open.
3. Pull wire through 7/8” hole in backplate and feed
through wire channel to lower left corner of backplate
before routing to terminal block (refer to appropriate
FACP manual).
4. The cover must remain attached to the backplate
while mounting the annunciator to the electrical box/
wall. The cover cannot be reattached or removed
after the annunciator has been mounted.
5. If the cover should become detached from the
backplate, reattach as shown below.
6. Surface or Semi-flush mount the ANN-80 to a single,
double or 4” square electrical box. The
ANN-SB80KIT(-R/-B/-W) is an available kit that
contains two plastic backboxes that can be used to
surface mount the ANN-80 Series.
Backplate
Press in latch
and then
Pull open cover
Key switch shown
in OFF position
Cover with
LCD Display
Figure 1 Opening the ANN-80 Series
ann-80_iso2.wmf
ANN-80
Series
Cover
ANN-80
Series
Cover
ANN-80
Series
Backplate
ANN-80
Series
Backplate
• Position cover behind
backplate.
• Align hinge posts and
holes
• Slide holes down
onto posts.
• Close cover to lock
hinges into place.
Figure 2 Cover Reattachment
ann80doormount.wmf

2ANN-80 Series Installation Document — P/N 52749:D1 8/17/10
Wiring the ANN-80 Series to the FACP
Refer to Table 1 and Figure 3 for wiring connections.
Notes:
1. All connections/sources are to be power-limited and
supervised.
2. 12 - 18 AWG (0.75 - 3.25 mm2) wire for 24 VDC
circuit is acceptable.
3. Power wire distance limitation is set by 1.2 volt
maximum line drop from source to end of circuit.
4. Maximum distance from FACP to last ANN-BUS
device must not exceed 6,000 feet (1,800 m). Refer to
Wiring Distance Table in appropriate FACP manual
for wire gauge and distance limitations.
Setting the DIP Switches
Each ANN-BUS device requires a unique address.
ANN-80 Series DIP switch S21 is used to set the address.
This address will be displayed on the LCD display as the
Station ID number.
A maximum of 8 devices can be connected to the FACP
ANN-BUS communication circuit. ANN-BUS device
addresses do not need to be sequential and can be set to
any number between 01 and 08. Note that 00 is not a valid
address. The following illustrates the DIP switch settings
for each address (ID Number):
ANN-80 Series
Terminals (TB1)
FACP ANN-BUS
Terminals
Terminal 1 (-) (-)
Terminal 2 (+) (+)
Terminal 3 (A) A (ANN-BUS)
Terminal 4 (B) B (ANN-BUS)
Table 1 ANN-80 Series to FACP Connections
B (ANN-BUS)
A (ANN-BUS)
+ (24 VDC)
- (GND)
Connect to FACP ANN-BUS
and/or next device.
}
}Connect to FACP or UL Listed
Power Supply for Protective
Signaling and/or next device.
ANN-80 Series
Figure 3 Wiring the ANN-80 Series to an FACP
ann-80boardterms.wmf
ID Number
(Address)
(not valid) 00
01
02
03
04
05
06
07
08
DIP Switch S21
dipaddresses.wmf