Ercol Ballatta Desk 2202 User manual

2202 BALLATTA DESK
Thank you for purchasing this Ballatta desk. Please ensure instructions are read in full before attempting to assemble
product.
1
Ref: 2507 / 2202
This product is heavy, it should be assembled as near as possible to the point of use.Take care when lifting to avoid
personal injury and (or) damage to the product.
The fittings pack contains small items which should be KEPT AWAY FROMYOUNG CHILDREN.
Read this leaflet in full before commencing assembly.
WARNING:
IN ORDERTO PREVENT OVERTURNING,THIS PRODUCT PRODUCT MUST BE USED WITHTHE WALL
ATTACHMENT DEVICE PROVIDED.
Installation should be carried out exactly according to the manufacturers instructions, otherwise a safety risk can
occur if incorrectly installed. Cabinets and shelving over 600mm high can be unstable and should be supported until
fixed to the wall.

Please check the pack contents before attempting to assemble this product.A full checklist of components is given
in this leaflet. If any components are missing, please contact the retailer from whom you bought this product.
2
Ref: 2507 / 2202
Pre-assembly preparation
This is a two person operation
Items you will need
Parts checklist
1
1 x top panel
2
1 x R/H side frame
3
1 x L/H side frame
4
2 x rail
5
1 x drawer
68mm x 600mm x 1100mm
31mm x 600mm x 730mm
31mm x 600mm x 730mm
25mm x 62mm x 948mm
105mm x 330mm x 519mm
Fitting checklist
A
4 x cam head
B
4 x grub screw
4 x cam rod
C
4 x allen head bolt (chrome - 6mm x 30mm)
D
4 x allen head bolt (chrome - 6mm x 70mm)
G
2 x screw (chrome - 3,5mm x 16mm)
H
i
4 x washer
J
K
2 x textile strap
1 x wedge
3
4
5
4
2
1
E
4 x wooden dowel (10mm x 35mm)
F
1 x allen key (M.4)

1. Place 4x cam heads (A) and 4x wooden dowels (F) into the holes of each rail (4). Use a soft hammer to insert
the dowels (F) as shown below
2. Lay down the side frames (2 and 3) on a smooth surface. Fix 4x cam rods (C) by using a screwdriver.
Step by step assembly instructions
Ref: 2507 / 2202 3
x2
4
A
F
F
A
CC
2 / 3
C
C

4.With the aid of an assistant, carefully attach the LH side frame (3) to the rails (4) by using 2x grub screws (B).
3. Place the rails (4) on side frame (2). Put 2x grub screws (B) into cam heads (A) and tighten them by using a
screwdriver.
Ref: 2507 / 2202 4
BB
44
2
B
B
B
B
B
B
3
4
4

5. Place the top panel upside-down and with the aid of an assistant, carefully locate the leg frames onto the top
panel (1) as shown below. Fix it with 8x allen head bolts (D and E) by using the allen key (G).
6. Place the drawer (5) into the unit as shown below. Note that there is a plastic stop located under the top panel
to hold the drawer in its location. Before inserting the drawer, the stop should be turned to face the rear of the
unit & before removing the drawer, turn the stop to face to front.
Ref: 2507 / 2202 5
1
5
G
E
E
D
D
G
Locate all 8 connecting bolts
before tightening!
E
DD
DD
E
E
E