Ercol Shalstone 80311506 User manual

YNG TAL 14 / ESMT4 D: 09.07.2015 / RN 002
Thank you for purchasing this Shalstone 4 drawer chest. Please read the instructions carefully before use to
ensure safe and satisfactory operation of this product
The fıttings pack contains SMALL ITEMS which should be KEPT AWAY FROM YOUNG
CHILDREN.
This product is HEAVY, it should be assembled as near as possible to the point of use.TAKE CARE
WHEN LIFTING to avoid personal injury and (or damage to the product.
Please check the pack contents before attempting to assemle this product. A full checklist of components is given
in this leaflet. If any components are missing, please contact the retailer from whom you bought this product.
Pre
-
assemb y preparation
Please ensure instructions are read in full before attempting to assemble this product.
This item is
HEAVY
Shalstone 4 drawer chest
Stock numbers 80311506
Necessary
Too s
This product is product takes approximately 20 MINUTES TO assemble with 2 PEOPLE.
Page 1 of 4

C Textile Strap x 1 A Screw (3,5mm x 16mm x 1
Wedges x 2B
Fittings and parts check ist
Wa fixing
-
if in doubt seek professional advice
Wood
If fixing to wood make sure
that it isn't chipboard as
screws can easily pull away
from the core structure
Brick or Masonry
Use an appropriate wall plug
provided you are sure your
wall is sound
Cavity wa
Special toggle wall plugas are
needed. Seek expert advice
1. Screw the textile strap on to the back edge of top panel of the item at centre point using short screw provided.
Position the item against the wall where you want it to go
2. Attach the textile strap using screws suitab e for your type of wa , see Wa fixings above.
fig.
1
fig.
2
fig.
3
Page 2 of 4

4. If after attaching your cabinet to the wall it is not standing level, use the wedges ( B provided.
Push a wedge under the corner of your cabinet until it becomes level, (fig.4 then snap it off as
shown in fig.5 Finally tap any of the wedge still protruding out from under the furniture, fig.6
A
C
fig.
4
fig.
5
fig.
6
Page 3 of 4

Care and Maintenance
Wood Furniture
Wood displays different grain patterns depending on which way it is cut
-
for example, the 'medullary ray'
which can appear on oak furniture is a mark of good quality timber - these are just characteristics of the
natural beauty of wood. Some furniture is also deliberately aged and rustic.
All timber surfaces will change colour and mellow over time. New furniture will initially vary in shade from
items that have been previously purchased.
How to care for your wood furniture
Furniture with a hard lacquer, wax polish or painted surface should be dusted with a dry cloth. When using
the surface for serving food and drinks it is best to use protective mats and coasters. Spillages should be
wiped up as soon as possible.
Spray polishes are best avoided as they contain silicones which may spoil the furniture's surface by building up
over time. Use of cleaning materials containing abrasive compounds, acidic or caustic reagents and any
bleaches containing oxidising reagents should be avoided as prolonged use may damage the lacquer surface.
Wipe up spills immediately. If sticky marks occur on the surface they can be removed with a dilute solution of
warm soapy water. The offending area should be rubbed lightly and then completely dried immediately
afterwards, before replacing any mats etc.
Our furniture will endure most temperatures in the home but it is best to avoid placing furniture next to heat
sources such as radiators or fires. Be particularly careful with solid wood as the lack of humidity caused by
central heating can cause damage such as warping.
Never drag furniture when moving it, always lift it. Please take care when handling or moving the furniture as
careless handling may cause damage or injury. No liability will be accepted for damage or injury caused by
incorrectly installed furniture.
Safety Instructions
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE
Ercol Furniture Ltd, Summerleys Road, Princes Risborough, Buckinghamshire. HP2 9PX www.ercol.com
Page 4 of 4