Ercol Bosco 1366 User manual

ercol
bosco
1366 3 door wardrobe
Thank you for purchasing this bosco wardrobe. Please read the instructions carefully before use to
ensure safe and satisfactory operation of this product.
This product is HEAVY, Take care when lifting to avoid personal injury and (or) damage to the product.
Please check the pack contents before attempting to assemble this product.A full checklist of
components is given in this leaflet. If any pieces are missing, please contact theretailer from whom you
bought this product.The fttings pack contains SMALL ITEMS which should be KEPT AWAY FROM
YOUNG CHILDREN.
Necessary Tools
This product takes approximately 30 MINUTES to assemble with 2 PEOPLE.

Fittings and parts checklist
ABase unit x 1
BLH side panel x 1
CRH side panel x 1
DCentre panel x 1
EBack panels x 3
F
G
Narrow hanging rail x 1
H
Wide hanging rail x 1
I
Top panel
J
Door panels
K
Shelf
L
M
N
O
Wedge x 2
P
Wooden dowel x 9
Q
Shelf pins x 8
25mm screws x 12
18mm screws x 34
14mm screws x 8
RM6*30mm bolts x 8
M6*50mm bolts x 4
SHalf Moon Washer x 4
Allen Key x 1T
Anti-tipping kit x 1
x 3
x 2
x 1

Step by step instructions
1, Check that all the wooden dowels are present in the side panels (B & C) & centre panel (D).
2.
With the help of another person locate the side panels & centre panel into the base unit. Secure using
(R)M6*30mm bolts.
Locate the top panel(H) as shown below secure on the left and right side panels using 4pcs (S)M6*50mm
bolt and half moon washersthen using 2pcs (R)M6*30mm bolt secure top panel on the top of centre panel.
R
T
R
R
S
S

3.
With the help of another person move the wardrobe close to it’s final position. If your floor is uneven
the other person may need to tilt the wardrobe slightly so that the doors remain square, then fix 3pcs
back panels(E) onto side panels(B&C) and centre panel(D) using the 18mm screws(N) as shown below.
4.
Secure 9pcs wooden dowels(P) onto the door frame(I) as shown below.
N
P

6. Push fit the eight shelf pins(Q) and locate the self (J) using 14mm screws(L) 8pcs as shown,
Put the hanging rails(F&G) into their rail supports.
5. Fix the door frame(I) onto the side panels(B&C) and centre panel(D) using the 25mm screws(M) 12pcs as
shown below.
M

Move the wardrobe into it’s final position against the wall.Align the L bracket to the pre drilled holes
on the top of your wardrobe in the middle along the back rail and using the 2 x 15mm screws fix the
bracket to the top of your wardrobe. Then make a mark on your wall through the two holes of the
bracket. Take the wardrobe away from the wall.Then drill two holes in your wall where your marks
are. Move the wardrobe back into place, align the bracket up with the holes in your wall and partially
tighten the bracket to the wall using appropriate fixings for your type of wall.
7. We recommend that you fix this wardrobe to the wall, using appropriate fixings for your type of wall,
see below.
O x 2
8. If the wardrobe needs levelling, use the wedges as shown below.
If the chest is not level on your floor, use the wedges provided.
Snap them off, so they do not protrude out from the cabinets legs.
You can also snap them lengthways. See diagram right.

10. Finally, using the provided Anti-tipping kit(K) to fully tighten the screws to secure the wardrobe to
your wall as shown below.
9. Check that the doors are aligned correctly. If necessary adjust the door hinges as shown below.
K

Care and maintenance
Wood Furniture
Wood displays different grain patterns depending on which way it is cut - for example, the ‘medullary ray’
which can appear on oak furniture is a mark of good quality timber - these are just characteristics of the
natural beauty of the wood. Some furniture is also deliberately aged and rustic.
All timber surfaces will change colour and mellow over time. New furniture will initially vary in shade
from items that have been previously purchased.
How to care for your wood furniture
Furniture with a hard lacquer, wax polish or painted surface should be dusted with a dry cloth.
When using the surface for serving food and drinks it is best to use protective mats and coasters.
Spillages should be wiped up as soon as possible.
Spray polishes are best avoided as they contain silicones which may spoil the furniture’s surface by
building up over time. Use of cleaning materials containing abrasive compounds, acidic or caustic reagents
and any bleaches containing oxidising reagents should be avoided as prolonged use may damage the
lacquer surface.Wipe up spills immediately. If sticky marks occur on the surface they can be removed
with a dilute solution of warm soapy water.The offending area should be rubbed lightly and then
completely dried immediately afterwards, before replacing any mats etc.
Our furniture will endure most temperatures in the home but it is best to avoid placing furniture next
to heat sources such as radiators or fires. Be particularly careful with solid wood as the lack of humidity
caused by central heating can cause damage such as warping.
Safety Instructions
Never drag furniture when moving it, always lift it. Please take care when handling or moving the
furniture as careless handling may cause damage or injury. No liability will be accepted for damage or
injury caused by incorrectly installed furniture.
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE
Ercol Furniture Ltd, Summerleys Road, Princes Risborough, Buckinghamshire. HP27 9PX www.ercol.com
ercol