ESI FLEX2-SLV User manual

ASSEMBLY AND OPERATION
ALL-FLEX™Model FLEX2-SLV
Model FLEX2-BLK
Model FLEX2-WHT
ELECTRIC TABLE BASE
FLEX2 Rev A 1/17

2
ALL-FLEX™ELECTRIC TABLE BASE PARTS AND TOOLS
PLEASE REVIEW these instructions before beginning the assembly procedures. Check that all the parts shown
below were provided with your order. Contact your supplier if any materials are missing. Do not discard the
packaging until satised that the product operates to your satisfaction.
PARTS AND TOOLS PROVIDED
Frame (1)Leg with Motor (2)
Digital Keypad (1)Control Unit (1) Cable Clip (4)Power Cable (1)
Adjustable Feet (2)
CAUTION:
Hand-tighten screws only. Do not use power tools.
Control Unit Bracket (1)
Fasteners Allen Keys (1 each)
M6x10 (8)M6x20 (8)M5x18 (22) M4x25 (2)
M6x8 (2) 4mm 8mm6mm5mm
CAUTION: Always check that screws used to
attach components to the work surface are
not too long for the thickness of the surface.
Work
Surface
ADDITIONAL TOOLS REQUIRED
• Phillips screwdriver

3
Align Long Notches
in Cross Channel with
Holes in Base of Leg
ASSEMBLY ALL-FLEX™ELECTRIC TABLE BASE
STEP 1
With the table top facing down on a soft, clean surface,
arrange the frame and leg columns as shown.
• The mounting tabs on the frame face down so that
they are against the work surface.
• The leg columns should be spaced so that the
columns are about the same distance apart as
the openings on the frame.
STEP 2
Lower the frame over the leg columns.
• The long notches in the cross channel t
over the holes on the cord side of the
leg column base.
STEP 3
Route the motor cables under the notches
near the center of the frame.
STEP 4
Prepare the frame so that it can be
expanded.
• Remove the four machine screws from
the center of the cross channel using the 4mm Allen
key. Save the screws for re-installation later.
• Loosen the two set screws on the rear of the frame using
the 6mm Allen key. Do not remove the set screws.
Space
Leg Columns
to Match
Openings
in Frame
Leg
Column
Frame
Front
Remove
Route Motor
Cables Under
Notches
Loosen

4
ALL-FLEX™ELECTRIC TABLE BASE ASSEMBLY
STEP 5
Attach the leg columns to the frame using four M6x10
screws per leg.
• Use the 5mm Allen key.
• Expand the cross channel so that its inner
piece can be moved to expose the holes
for the screws at the rear of the frame.
STEP 6
Change the length of the adjustable feet, if necessary.
• The length of the feet may be either 22" (55.9cm) or 28" (71.2cm). The feet are shipped in the 28" length.
They should be changed to the shorter length if the work surface depth is less than 28".
• To change the length to 22", rst remove the adjustment plate. Then use a 5mm Allen key to remove the
four screws, as shown.
• Slide the feet to the 22" length and reinstall the four screws with the 5mm Allen key.
• Store unused adjustment plates in the brackets attached to the frame.
M6x10
Expand Cross
Channel to Expose
Holes for Rear Screws
Adjustment
Plate
5mm
Allen Key
Slide In
22"
Adjustable
Length
28"
Store
Adjustment
Plates

5
ASSEMBLY ALL-FLEX™ELECTRIC TABLE BASE
M10x20
8mm Allen Key
Align Rear of Feet with Rear of Table
1" Minimum
Install
Machine
Screws
Tighten
Set Screws
Expands from
34" to 64"
Center
1" Minimum Space
Each Side
STEP 7
Attach a foot to each of the legs.
• Use four M10x20 screws per foot.
• Tighten the screws with an 8mm Allen key.
STEP 8
Adjust the position of the frame before screwing
it to the work surface.
• Align the rear of the feet with the rear of the table.
• Expand the frame, if necessary, and center it from
side to side. See Steps 9 and 10.
• Expand the top supports, if necessary. See Step 11.
STEP 9
Expand the frame, if necessary. The frame should extend the full width of the table, allowing a minimum
space of 1" (25mm) on each side.
• The frame can be expanded from
34" (86cm) wide to 64" (163cm) wide.
The inner channel includes guides to
assist in setting the desired width.
• Be sure the frame is centered
on the work surface.
STEP 10
After expanding the frame,
re-install the four machine screws
and tighten the two set screws.
• The tab on the inner channel should
be approximately centered.

6
ALL-FLEX™ELECTRIC TABLE BASE ASSEMBLY
M5x18
Remove
Screws 19¼"
Expand
23½"
Install
Screws
STEP 11
If the table depth is 30" (76cm) or more, expand the top supports on each side.
• Remove the two machine screws from the top support using the 4mm Allen key.
• Slide the top supports to the longer length, as shown below.
• Re-install the machine screws in the forward two holes of the top support.
STEP 12
Once the frame is in its nal position, attach it to the work surface using the M5x18 screws (20 total required).
• Attach the screws through the
mounting tabs on the frame, the
mounting tabs on the inner piece
of the cross channel, and the holes
at the ends of the top supports.
• Use a Phillips screwdriver.

7
STEP 13
Attach the control unit bracket to the frame and
the control unit to the work surface.
• Secure the control unit bracket to the frame using
two M6x8 screws and a 4mm Allen key.
• The bracket may be attached on either side of
the frame. (Note that the digital keypad will be
attached on the same side.)
• Attach the control unit under the bracket using
M5x18 wood screws. The motor cable and
keypad ports should face the center of the table,
as shown.
• Allow 2¼" (57mm) between the back of the
control unit and the top support to allow room for
power cord attachment.
STEP 14
Attach the digital keypad at the front edge of the
work surface.
• Use the two M4x25 wood screws.
• Attach the keypad on the same side as the
control unit.
STEP 15
Make connections to the control unit.
• Connect the cable from the digital keypad.
• Connect the motor cables from the motors.
• Connect the power cord to the control unit.
• Plug the power cord into an AC outlet.
CAUTION: Do not operate the table until after
“zero setting” the system. See following step.
ASSEMBLY ALL-FLEX™ELECTRIC TABLE BASE
M5x18
Control
Unit
Bracket
2¼"
M6x8
M4x25
Digital
Keypad
Motor
Cables
Keypad
Cable
Control
Unit
Power
Cable

8
STEP 16
“Zero set” the system before testing operation. (Note that with the table and keypad upside-down, the
UP sand DOWN t buttons face their opposite directions.)
• Press and hold the UP sand DOWN t buttons at
the same time. Continue to hold the buttons. The
legs will lower until they reach their bottom point.
• Release the buttons once the system beeps. If it
does not beep, continue to hold the buttons for
3 seconds after the legs reach the lowest point. The
system is now “zero set.”
• Press the UP sand DOWN t buttons to test operation. End your test with the legs lowered and unplug the
power cord.
• If there are problems with operation, check that all cable and cord connections are secure. If problems
continue, call ESI Customer Service.
STEP 17
Use the pre-installed cable clips plus the additional ones provided to secure the cables in position.
• Cables must not interfere with table operation.
• Cables must not interfere with the user.
ALL-FLEX™ELECTRIC TABLE BASE ASSEMBLY
Digital Keypad
Work Surface
Press and Hold Both Buttons
Cable Clip

9
STEP 18
With the assistance of a helper, turn the table upright and place it in its nal position.
IMPORTANT: There must be 1" (25mm) of clearance on all sides of the work surface (and other moving parts)
to ensure free, unobstructed movement.
• Adjust the leveling glides on the feet to level the work surface, if necessary.
• Plug the power cord into an AC outlet.
• See the following page for
operating procedures.
ASSEMBLY ALL-FLEX™ELECTRIC TABLE BASE

10
ALL-FLEX™ELECTRIC TABLE BASE OPERATION
GENERAL OPERATION
Move the table up or down by pressing UP sor DOWN tuntil
the work surface reaches the desired height.
The table will continue to move up or down until you release the
button or until the maximum or minimum height is reached.
IMPORTANT: Be sure there are no obstructions to table
movement along its full range of travel.
SETTING A MEMORY POSITION
The memory buttons allow you to save up to four specic
positions of the work surface. To set a memory position:
• Adjust the work surface to the position you want to save. (The
display on the control pad shows the work surface height.)
• Press the UP sbutton and one of the memory buttons at the
same time for 3 to 5 seconds.
• The display will ash “P” and the number of the memory
button.
• Repeat for the other memory buttons, if desired.
MOVING TO A MEMORY POSITION
• Press and hold the desired memory button.
• The work surface will move to the preset position.
CAUTION: The “zero setting” procedure
must be completed before operating the
table. See Step 16 on page 8.
Example: Press the UP s button and
memory button number 3 at the
same time for 3 to 5 seconds. The
display will ash “P3” indicating that
the current table position has been
saved in memory.
Continue to press the memory button
until table movement stops.
Table movement stops when you
release the UP s or DOWN t button.
Memory
Buttons
Table
Height
UP
Button
Memory
Buttons
DOWN
Button

800.833.3746 esiergo.com
© 2017 ESI Ergonomic Solutions. All rights reserved. FLEX2 Rev A 1/17