ESI VICTORY ELECTRIC-3-LEG User manual

1. LAY (A) LEGS, (B&C) ADJUSTABLE CROSS CHANNELS, (G&E)
FEET AND (D) TOP SUPPORTS ON THE FLOOR.
2. ATTACH (A) LEG COLUMNS TO (B&C) CROSS CHANNELS AND
(D) TOP SUPPORTS USING (K) M8 SCREWS (X12). DO NOT
TIGHTEN SCREWS COMPLETELY UNTIL ALL PIECES HAVE BEEN
ATTACHED TOGETHER.
3. ATTACH THE (F) FOOT PLATES USING (N) M6 SCREWS (X8) AND
(G&E) FEET USING (L) M6 SCREWS (X8) BE SURE THE LONGER SIDE
OF THE FOOT GOES TOWARDS THE FRONT OF THE TABLE.
TIGHTEN SCREWS COMPLETELY.
4. ADJUST (B&C) CROSS CHANNELS TO APPROPRIATE LENGTH AND TIGHTEN SECURELY
USING M10 (X12) SCREWS PROVIDED WITH CROSS CHANNELS.
5. ATTACH WORKSURFACE USING APPROPRIATE LENGTH SELF-TAPPING SCREWS. BE SURE
SCREWS ARE CORRECT LENGTH SO AS NOT TO PIERCE TOP OF WORKSURFACE.
6. ATTACH (J) KEYPAD/SWITCH AND (K) CONTROL UNIT UNDER WORKSURFACE IN
PREFERRED LOCATIONS USING (M) M5 SCREWS.
7. ATTACH (H) LEG CABLES.
8. TIGHTEN ALL SCREWS SECURELY.
9. MANAGE CABLES APPROPRIATELY AND IF NECESSARY, ADJUST LEVELING GLIDES ON
TABLE FEET TO LEVEL THE WORKSURFACE.
ASSEMBLY GUIDE VICTORY ELECTRIC - 3-LEGASSEMBLY GUIDE VICTORY ELECTRIC - 3-LEG
10. INITIALIZE LEGS: AFTER TABLE BASE IS FULLY ASSEMBLED AND
POWER CORD HAS BEEN PLUGGED IN, HOLD DOWN BOTH UP AND
DOWN BUTTONS ON KEYPAD/SWITCH FOR 5-10 SECONDS OR UNTIL
BOTH LEGS ARE IN THE LOWEST POSITION. TABLE BASE MUST BE
ZERO-SET BEFORE USE!
2
1
3
54
&

esiergo.com | 800.833.3746
ASSEMBLY GUIDE VICTORY ELECTRIC - 3-LEG
PARTS USED IN ASSEMBLY
A
B
GF
D
KL M N
x3
LEG
COLUMN
x2
INTERIOR/EXTERIOR
CROSS CHANNEL
(PRIMARY SIDE)
x3
TOP SUPPORT
x2
FEET
x2
FOOT PLATE
x12
M8 SCREWS
(LEGS)
x8
M6 SCREWS
(FEET)
x17
M5 SCREWS
(TOP SUPPORT &
CABLE BOX)
x2
M4.2 SCREWS
(KEYPAD)
SETTING TABLE TO ZERO
IMPORTANT! TABLE MUST BE ZERO-SET PRIOR TO USE.
1. PRESS BOTH BUTTONS AT THE SAME TIME FOR 5-10 SECONDS. THIS WILL ACTIVATE ZERO-SETTING MODE.
2. CONTINUE TO HOLD BOTH BUTTONS DOWN UNTIL BOTH LEGS ARE IN LOWEST POSITION.
3. THE TABLE IS NOW ZERO-SET AND READY TO USE.
IMPORTANT! HAND TIGHTEN KEYPAD SCREWS, DO NOT USE POWER TOOLS.
MAKE SURE ALL SCREWS ARE TIGHTENED ACCORDING TO THE TORQUE INFORMATION BELOW:
FEET SCREWS = 10NM
LEG SCREWS = 13NM
SUPPORT & CABLE BOX SCREWS = 6NM
Jx1
KEYPAD/SWITCH
I
x1
CONTROL UNIT
W/ POWER CORD
Hx3
LEG CABLE
PART NUMBER
3VT-C4836-30
3VT-C4848-24
3VT-C4848-30
Cx2
INTERIOR/EXTERIOR
CROSS CHANNEL
(SECONDARY SIDE)
Ex1
GLIDE FOR
CENTER LEG