ESI LIFT User manual

ASSEMBLY AND ADJUSTMENT
LIFT Model LIFT-SLV
DESK-CLAMP
LIFT Rev A 3/17

2
PLEASE REVIEW these instructions before beginning the assembly and adjustment procedures. Check that
all the parts and tools listed below were provided with your order. Contact your supplier if any materials are
your satisfaction.
LIFT ERGORISE PARTS AND TOOLS
Main Assembly (1) Keyboard Platform (1)
PARTS AND TOOLS PROVIDED
CAUTION: Hand-tighten screws only.
Do not use power tools.
Desk Clamp and Track (1)
6mm Allen Key (1)
5/8" Wrench (1)
4mm Allen Key (1)Keyboard Hole Plug (2)M6x8mm Screw (8)
WARNING: When you first squeeze the paddle lever to operate this product, there
is no load on the unit. Firmly hold the column base to control the rate of movement.
Take appropriate precautions to avoid pinching or otherwise injuring yourself.

3
Change Side of Keyboard Palm Rest, If Desired
By default, the keyboard palm rest is on the left side for a right-side mouse. If desired, it may be changed to
the right side for a left-side mouse.
• Using the 4mm Allen key, remove the screws holding the palm rest from the underside of the keyboard
platform. Remove the plug from the far right-side hole.
• Re-install the screws to attach the palm rest to the right side of the keyboard platform. Use one of the new
plugs provided to conceal the exposed left-side hole.
Attach the Keyboard Platform
• Position the product with the top platform on the work surface and the column base to the rear.
• Using the 4mm Allen key, attach the keypad with two M6x8 screws, as shown. Tighten securely.
ASSEMBLY LIFT
Right-Side Mouse Left-Side Mouse
Keyboard Platform
Top Platform
M6x8 Screws

4
LIFT ASSEMBLY
Change Side of Paddle, If Desired
By default, the paddle is attached to the right
side of the top platform. If desired, it may be
changed to the left side. Holes are pre-drilled
on the left side for your convenience.
• Use the 4mm Allen key to remove the paddle
from the right side of the top platform.
• Re-attach the paddle to the left side of the
platform.
Attach the Desk Clamp and Track to the Work Surface
The desk clamp requires 4" of clearance under the work surface for attachment. The clamp
accommodates work surface thicknesses from ¾" to 3.3" (20mm to 80mm).
Adjust Clamp, If Necessary
• The clamp as shipped can be
attached to work surfaces from
1¾" to 3.3" thick.
• For thinner work surface thicknesses, the three screws on
the clamp portion may be removed and the clamp
re-attached in one of the other three sets of holes. Each
set of holes is 1" apart.
Attach Clamp
• Position the clamp at the desired location, with the
surface.
• Use the provided 5/8" wrench to tighten the clamp
bolts.
IMPORTANT: Be sure the clamp is securely tightened.
Paddle
Remove Screws
to Adjust Clamp
¾"
3.3"
Tighten
Securely!
Work Surface
5
/8" Wrench

5
ASSEMBLY LIFT
Attach Main Assembly to Clamp Track
then turned over, positioned on the track, and screwed in place.
Raise Column
• Place your hand on the end of the column to control
the rate of movement.
• Depress the paddle lever. Feather it to further
control the rate of movement.
WARNING: Stand well away from the path of
column movement. The column could raise
quickly and suddenly, potentially causing injury.
Position Base of Column on Clamp Track
The position of the column base varies depending upon work surface depth. See illustrations.
• Turn the main assembly over so that the base is on the bottom.
• Position the base toward the front of the track with deeper work surfaces.
• Position the base toward the rear of the track with shallower work surfaces. Allow at least one set of two
holes to remain exposed at the rear of the track for attachment of the support bracket.
Attach Base of Column to Clamp Track
• Use four of the M6x8mm screws to attach
the base, as shown.
• Tighten the screws using the 4mm Allen
key.
Depress
Paddle
Lever
M6x8
24"
Depth
30"
Depth

6
45°
LIFT ASSEMBLY
Test Operation
• Place the monitor and other equipment that will be used with this product
on the top platform and keyboard platform.
• Depress the paddle lever. Raise and lower the unit through its full range of
movement.
•
If Necessary, Adjust for Load Weight
This adjustment can be used to maximize ease of operation. When operating this product, the platform
should move easily to any position and hold that position.
•
• – ).
• Use the 6mm Allen key to turn the adjusting screw — counterclockwise to increase load, clockwise to
decrease it.
• Test operation and re-adjust as necessary.
CAUTION: Do not over-tension the MAX (+) adjustment.
6mm Allen Key
M6x8

800.833.3746 esiergo.com
© 2017 ESI Ergonomic Solutions. All rights reserved. LIFT Rev A 3/17