ESI TRIUMPH 2T-C28-24 User manual

ASSEMBLY GUIDE TRIUMPH ELECTRIC - 2-LEGASSEMBLY GUIDE TRIUMPH ELECTRIC - 2-LEG
6
1
7
1. ATTACH (I) FOOT PLATES AND (D) FEET TO BOTH (A&B) LEG
COLUMNS USING (N) M6X35 SCREWS (X8) BE SURE THE LONGER
SIDE OF THE FOOT GOES TOWARDS THE FRONT OF THE TABLE.
2. SET (B) LEG WITHOUT MOTOR UPRIGHT AND MANUALLY PUSH
DOWN TO THE LOWEST POSITION.
3. SET (A) LEG WITH MOTOR UPRIGHT.
4. ATTACH (F) CROSS CHANNEL TO THE (A&B) LEG COLUMNS USING
(M) M6X8 SCREWS (X4).
5. ATTACH THE (C) TOP SUPPORTS TO THE LEG COLUMNS USING
(O) M8 SCREWS (X4).
6. ATTACH THE (D) CROSS CHANNELS TO APPROPRIATE LENGTH AND TIGHTEN SECURELY
USING THE (L) M10 SCREWS (X4).
7. CONNECT THE 2 LEGS WITH THE CONNECT BAR (PULL THE CONNECT BAR TO THE
APPROPRIATE LENGTH).
8. ATTACH WORKSURFACE USING APPROPRIATE LENGTH SELF-TAPPING SCREWS. BE SURE
SCREWS ARE CORRECT LENGTH SO AS NOT TO PIERCE TOP OF WORKSURFACE.
9. ATTACH (J) KEYPAD/SWITCH AND (G) CONTROL UNIT UNDER WORKSURFACE IN
PREFERRED LOCATIONS.
10. ATTACH (H) LEG CABLE TO LEG WITH MOTOR ONLY.
11. CONNECT (J) KEYPAD SWITCH TO CONTROL UNIT. PLUG IN CONTROL UNIT TO POWER
SOURCE AND MOVE LEG DOWN TO THE LOWEST POSITION USING THE KEYPAD SWITCH.
12. TIGHTEN ALL SCREWS SECURELY.
13. MANAGE CABLES APPROPRIATELY AND IF NECESSARY, ADJUST LEVELING GLIDES ON
TABLE FEET TO LEVEL THE WORKSURFACE.
14. INITIALIZE LEGS: AFTER TABLE BASE IS FULLY ASSEMBLED AND
POWER CORD HAS BEEN PLUGGED IN, HOLD DOWN BOTH UP AND
DOWN BUTTONS ON KEYPAD/SWITCH FOR 5-10 SECONDS OR UNTIL
BOTH LEGS ARE IN THE LOWEST POSITION. TABLE BASE MUST BE
ZERO-SET BEFORE USE!
8

x1
CROSS
CHANNEL
esiergo.com | 800.833.3746
ASSEMBLY GUIDE TRIUMPH ELECTRIC - 2-LEG
PARTS USED IN ASSEMBLY
I
C
MO
K
x2
TOP SUPPORT
x2
FOOT
PLATES
x1
LEG CABLE
x4
M8 SCREWS
x4
M6X8 SCREWS
x6
M5 SCREWS
SETTING TABLE TO ZERO
IMPORTANT! TABLE MUST BE ZERO-SET PRIOR TO USE.
1. PRESS BOTH BUTTONS AT THE SAME TIME FOR 5-10 SECONDS. THIS WILL ACTIVATE ZERO-SETTING MODE.
2. CONTINUE TO HOLD BOTH BUTTONS DOWN UNTIL BOTH LEGS ARE IN LOWEST POSITION.
3. THE TABLE IS NOW ZERO-SET AND READY TO USE.
IMPORTANT! HAND TIGHTEN KEYPAD SCREWS, DO NOT USE POWER TOOLS.
MAKE SURE ALL SCREWS ARE TIGHTENED ACCORDING TO THE TORQUE INFORMATION BELOW:
FEET SCREWS = 10NM
LEG SCREWS = 13NM
SUPPORT & CABLE BOX SCREWS = 6NM
Jx1
KEYPAD/SWITCH
G
x1
CONTROL UNIT
W/ POWER CORD
H
Ex1
CONNECT
BAR
B
x1
LEG
COLUMN
A
x1
LEG
COLUMN
W/
MOTOR
Dx2
FEET
F
Lx4
M10 SCREWS
Nx8
M6X35 SCREWS
PART NUMBER
2T-C28-24
2T-C28-30
2T-C40-24
2T-C40-30