ETC Source 4WRD II User manual

ETC Quick Guide
Source 4WRD II Version 1.1.2
Corporate He adqua rte rs Middleton, WI, USA [phone]
London, UK [phone] Holzk irchen, DE [phone]
Rome , IT [phone] Hong Kong [phone] P aris, FR [phone]
Web etcconnect.com Support support.etcconnect.com
Contac t etcconnect.com/contactETC © 2020 Electronic Theatre Controls, Inc.
Product information and specifications subject to change. ETC intends this document
to be provided in its entirety. Trademark and patent info:etcconnect.com/ip
7067M1330-1.1.2 Rev A Released 2020-10
Introduction
The Source 4WRDII LED is a replacement for a standard Source Four burner
assembly. It converts the HPL source to a white-light LED and provides a
significant reduction in power consumption.
For complete information, download the Installation and User
Manual at etcconnect.com, or view online help on your
smartphone or tablet by scanning this code.
What's in the Box
•
Source 4WRD II retrofit
•
Threaded post (see Install the Source 4WRD II Retrofit on page4 )
Safety
The Source 4WRD II fixture is intended for professional use only. Read the
entire manual before using this equipment.
WARNING: Note the following safety warnings before use:
•
Do not mount the fixture on or near a flammable surface.
•
Do not use this fixture with a damaged power lead. If the
power lead (cord set) is damaged, it must be replaced.
•
Mount and support the fixture only by the primary
suspension holes in the yoke.
•
Suspend the fixture from a suitable structure using only
hardware rated for the weight of the fixture.
•
In addition to primary suspension, attach a safety cable
(ETC Model 400SC or other approved safety cable or
device) to the fixture housing. An appropriate attachment
point (hole) is provided in the protruding tab on the fixture
housing.
•
Disconnect the unit from power and DMX and allow the
fixture to cool before removing or installing accessories,
and before all cleaning and maintenance.

ETC Quick Guide
Source 4WRD II Version 1.1.2
AVERTISSEMENT : Prendre connaissance des avertissements
de sécurité suivants avant toute utilisation :
•
Ne pas installer le projecteur sur ou à côté d’une surface
inflammable.
•
Ne pas utiliser ce projecteur avec un cordon d’alimentation
endommagé. Si le cordon d’alimentation (câble) est abîmé,
il doit être remplacé.
•
Installer et accrocher le projecteur uniquement par les
trous de fixation principaux de la lyre.
•
Accrocher le projecteur à une structure convenable en
utilisant seulement du matériel adapté au poids du
projecteur.
•
En plus de l'accroche principale, fixer une élingue de
sécurité (modèle ETC400SC ou autre câble/dispositif de
sécurité certifié) au corps du projecteur. Un point
d’accroche (trou) approprié est prévu dans la patte qui
ressort du boîtier du projecteur.
•
Déconnecter l’alimentation et le DMX et laisser le
projecteur refroidir avant d’enlever ou installer l'optique
découpe ou les autres adaptateurs, et avant tout
nettoyage et entretien.
WARNING: Note the following safety warnings before use:
•
The Source 4WRD II LED is not user serviceable. Field
modification of the Source 4WRD II LED will void your ETC
warranty.
•
Do not use the fixture below 5°C (41°F).
•
Minimum storage temperature is 5°C (41°F). When the
fixture has been stored or transported in cold
temperatures, allow it to warm to room temperature for
a minimum of 1hour before applying power. Applying
power to a cold fixture will cause damage to the fixture
and void the ETCwarranty.
•
Do not use this fixture if a glass lens is deeply scratched or
cracked. Damaged lenses must be replaced.
•
To prevent wiring damage, or abrasion, do not expose
wiring to edges of sheet metal or other sharp objects.
•
Use the fixture in dry locations only, where humidity does
not exceed 90 percent (non-condensing). These fixtures
are not intended for outdoor use.
Source 4WRD II Page 2 of 8 ETC

ETC Quick Guide
Source 4WRD II Version 1.1.2
Retrofit the Fixture
WARNING: RISK OF FIRE OR ELECTRIC SHOCK! Installing the
Source 4WRDII LED retrofit kit requires knowledge of luminaire
electrical systems. If you are not qualified, do not attempt
installation. Contact a qualified electrician.
AVERTISSEMENT : RISQUE D'INCENDIE OU DE DÉCHARGE
ÉLECTRIQUE! Installer le nécessaire de conversion Source 4WRDII
LED nécessite une connaissance des systèmes électriques de
projecteurs. Si vous n’êtes pas qualifié, ne tentez pas
l’installation. Faire appel à un électricien qualifié.
Note: THE RETROFIT KIT IS ACCEPTABLE AS A COMPONENT OF A
LUMINAIRE WHERE THE SUITABILITY OF THE COMBINATION SHALL BE
DETERMINED BY AUTHORITIES HAVING JURISDICTION.
Wire the Power Connector(If Needed)
If you ordered a Source 4WRD II retrofit without a power connector, wire the
connector in accordance with all national and local electrical codes:
•
Brown = Live
•
Blue = Neutral
•
Green/Yellow = Protective earth
Remove Incandescent Lamp Housing
1. Unplug the Source Four incandescent fixture and place it on a flat,
stable surface.
2. Loosen the brass thumb screw located above the beam adjustment
knob. The lamp housing is now loose.
3. Remove the lamp housing from the fixture body.
Source 4WRD II Page 3 of 8 ETC

ETC Quick Guide
Source 4WRD II Version 1.1.2
Install the Source 4WRD II Retrofit
WARNING: RISK OF FIRE OR ELECTRIC SHOCK! Install this kit only
onto luminaires that have the construction features and
dimensions shown in the images in this document and where the
input rating of the retrofit kit does not exceed the input rating
of the luminaire.
AVERTISSEMENT : RISQUE D'INCENDIE OU DE DÉCHARGE
ÉLECTRIQUE! N’installer ce kit que sur les projecteurs qui ont les
caractéristiques de construction et les dimensions indiquées sur
les images de ce document et où la puissance électrique
nécessaire à la conversion n’excède pas la puissance maximale du
projecteur.
WARNING: Do not make or alter any open holes in an enclosure
of wiring or electrical components during kit installation.
CAUTION: Do not touch or clean LED emitters with anything
other than oil-free canned air.
Tools required:
•
Adjustable wrench
•
#2 Phillips screwdriver
1. Use oil-free canned air to clean the LED emitters before you install the
retrofit. Do not touch the LEDemitters.
2. With the fixture resting securely on a flat surface, attach the supplied
threaded post to the back end of the fixture body. Use an adjustable
wrench to tighten the threaded post one-quarter turn past finger
tight.
3. Gently slide the Source 4WRDII LED onto the fixture body and
threaded post while guiding the LED tower into the lamp housing
hole, as shown in the following image. Take care to prevent contact
between the LEDs and the reflector.
Source 4WRD II Page 4 of 8 ETC

ETC Quick Guide
Source 4WRD II Version 1.1.2
Insert threaded
post here
Tighten
screw
Z-adjustment
knob
Source Four
fixture body
Lamp
housing
hole
4. Use a #2 Phillips screwdriver to tighten the screw located on the back
end of the Source 4WRDII LED, directly above the Z-adjustment knob.
5. Pull gently to verify secure attachment.
6. Set the Z-adjustment using the Z-adjustment knob. See Set the Z-
adjustment on page8 .
Attach C-clamp and Safety Cable
The C-clamp attaches the fixture to the mounting pipe and allows you to
adjust the position of the mounted fixture. ETC recommends using 1.5in
schedule 40 pipe.
1. Tightly fasten the C-clamp to the yoke with the provided yoke bolt and
lock washer.
2. Place the C-clamp on mounting pipe, and then tighten the pipe bolt to
secure it.
3. Loosen the C-clamp pan screw and rotate the yoke to the desired
position.
4. Tighten the pan screw to lock the fixture.
5. Connect the safety cable.
6. Tighten the C-clamp pipe bolt to 15–20 ft-lb (20–27 Nm),
approximately finger tight plus up to one-quarter turn.
CAUTION: Do not exceed 25 ft-lb (33 Nm) while tightening the
C-clamp pipe bolt. Do not use excessive force.
7. Tighten the yoke pivot bolt to 5–10 ft-lb (6–7 Nm), approximately
finger tight plus up to one-eighth turn.
CAUTION: Do not exceed 15 ft-lb (20 Nm) while tightening the
yoke pivot bolt. Do not use excessive force.
Source 4WRD II Page 5 of 8 ETC

ETC Quick Guide
Source 4WRD II Version 1.1.2
Connect Cables
You can control the fixture using AC power or DMX. Configure the fixture to
use the appropriate control method on the user interface. See Configure the
Fixture on the facing page .
WARNING: Do not use or store the Source 4WRD II fixture
below 5°C (41°F). When the fixture has been stored or
transported in cold temperatures, allow it to warm to room
temperature for a minimum of 1 hour before applying power.
Applying power to a cold fixture will cause damage to the fixture
and void ETC warranty.
Note: For optimum performance, make sure that your dimmer is out
of regulated mode. See Line-dimming on the facing page for
recommended dimmer settings.
Note: Connecting both power and data from a SmartBar 1 to a
Source 4WRD II fixture may cause flickering.
1. If you are using DMX control: Connect one RJ45 data cable for data-in
and one for data-thru, as needed. Use the strain relief at the bottom of
the fixture to support the data cables.
•
To order an RJ45-to-female XLR adapter, use ETC part number
W6538.
•
To order an RJ45-to-male XLR adapter, use ETC part number
W6539.
2. If you are using DMXcontrol and this is the last fixture in the line,
terminate the fixture with a 120Ohm resistor. Please contact your ETC
customer service representative to purchase ETC part number N4086.
3. Connect the fixture to the power source.
Source 4WRD II Page 6 of 8 ETC

ETC Quick Guide
Source 4WRD II Version 1.1.2
DMXDimming
When dimming via DMX, consider the following:
•
When using DMX over Cat5, use Cat5e or better.
•
Cable distance for full DMX daisy chain must not exceed 300m
(1000ft).
•
Up to 32 fixtures can be connected together into a daisy chain.
•
The fixture cannot be controlled via Ethernet protocols and should not
be directly connected to an Ethernet system.
•
When DMX data is lost, the LEDemitters turn off.
•
The fixture uses a single DMXchannel for intensity control.
Line-dimming
For the most current information on additional dimmer performance testing
for both ETC and non-ETC dimmers, please visit the ETC website:
https://support.etcconnect.com/ETC/Fixtures/Source_Four/Source_
4WRD%2F%2FSource_4WRD_PAR/Dimmer_Settings_for_Use_with_Source_
4WRD
Configure the Fixture
Up and down
navigation buttons
User interface
The two-button, seven-segment display
shows the DMXaddress, ACmode, or
the manually-set level. Use the up and
down navigation buttons to configure
the fixture.
•
Set a DMX address: Use the up
and down arrows to navigate to
thedesired DMX address number
(1–512).
•
Set the fixture to use line-
dimming (ACmode): Use the
down arrow to navigate one number
below DMX address 1. The display will read AC.
•
Manually set a level: Use the down arrow to navigate one number
below AC. The display will read L.FL (Level = Full). Usethe down arrow
to decrease the level to a percentage of full (L.99 = 99%, L.98 =
98%, etc.). You can set levels from 0%–100% (full).
Source 4WRD II Page 7 of 8 ETC

ETC Quick Guide
Source 4WRD II Version 1.1.2
Focus the Fixture
Set the Z-adjustment
Use the Z-adjustment knob located on the rear of the fixture to adjust the
field of the LED light for specific applications.
1. Turn on the fixture and aim it at a flat surface.
2. Slide the fixture barrel toward or away from the Source 4WRDII LED to
create a hard-edged beam of light.
3. Turn the knob toward PEAK or FLAT until you achieve the desired field.
Ideal beam of
uniform light
Adjust toward PEAK to
blend overlapped beams
Adjust toward FLAT to
improve sharp focus
Z-adjustment knob
Note: The Source 4WRD PAR or PARNel Fixture Body optics are
optimized for PEAKfocus. When using the Source 4WRDII LED in a
Source 4WRD PAR or PARNel Fixture Body, turn the Z-adjustment
knob toward PEAK until the knob becomes loose, and then tighten
the Z-adjustment knob an additional quarter turn. This sets the LED
light source into the appropriate position within the fixture.
Source 4WRD II Page 8 of 8 ETC