ETC CE Source Four User manual

CE Source Four
User Manual
Gebrauchsanleitung
Manuel d'utilisation
Manual del usuario

DECLARATION OF CONFORMITY
We, Electronic Theatre Controls, Europe Limited
Unit 5, Victoria Industrial Estate, London W3 6UU United Kingdom
declare under sole responsibility that the product
Product name: CE Source Four
Product type/model: CE Source Four series (405, 410, 419, 426, 436, 450)
Lot: n/a
Batch / Serial number: n/a
Item numbers: one of each model
to which this declaration relates is in conformity with the following standards:
EN60598-1:1993 Luminaires, General requirements and tests
EN60598-2-17:1989 Specification for luminaires for stage lighting, television,
film, and photographic studios.
following the provisions of EU LV Directive(s) 73/23/EEC
London, United Kingdom Mr. Adam Bennette
(Place of issue) (Name of authorised person)
_________________________ ____________________________
(Date of issue) (signature of authorized person)
Electronic Theatre Controls Europe Ltd. Registered office:
Unit 5, Victoria Industrial Estate, Grant Thornton House
Victoria Road, London W3 6UU U.K. Melton St., London, NW1 2BW, England
Telephone [phone] Registered in England No.3057796
Fax [phone] VAT No. 662 9487 90

CE Source Four 3
CE Source Four
Contents • Inhaltsverzeichnis • Table des matières • Indice
Specifications/Technische Daten
Spécifications/Especificaciones .......................................... 4
CE Source Four ................................................................... 5
CE Source Four Instructions ............................................... 7
CE Source Four Bedienungsanleitung .............................. 15
Mode d'emploi CE Source Four ........................................ 23
Instrucciones para CE Source Four ................................... 31

4CE Source Four
692mm
759mm
254mm max.
175mm min.
262mm
314mm
432mm
911mm
978mm
254mm max.
175mm min.
262mm
365mm
495mm
Specifications • Technische Daten
Spécifications • Especificaciones
10º Weight: 6.8kg
10º Gewicht: 6,8kg
10º Poids: 6,8kg
10º Peso: 6,8kg
5°Weight: 8.6kg
5°Gewicht: 8,6kg
5°Poids: 8,6kg
5°Peso: 8,6kg
19º, 26º, 36º, 50º CE Source Four
5º CE Source Four
10º CE Source Four
19º to 50º Weight: 6.3kg
19º bis 50º Gewicht: 6,3kg
19º à 50º Poids: 6,3kg
19°a 50°Peso: 6,3kg
337mm
426mm
200mm
254mm max.
175mm min.
222mm
546mm
613mm

CE Source Four 5
Spacer
Abstandshalter
Pièce d'écartement
Pieza separadora
Yoke locking knob
Bügelfeststellschraube
Poignée de serrage de la lyre
Maneta para fijar la lira
Secondary suspension point
Befestigungsmöglichkeit für Sicherungsseil
Point de suspension secondaire
Punto secundario de suspensión
Gel frame holder extender (model #400GE)
Abstandhalter für Farbrahmen (Modell #400GE)
Rallonge du porte-filtre (modèle #400GE)
Extensión del marco portagelatinas (modelo 400GE)
Barrel rotation knob
Knopf für Rotation des Basisgehäuses
Bouton de rotation du corps
Maneta de rotación del tubo
Earth continuity cable
Erdungskabel
Cable de mise à la terre
Cable de tierra
Colour frame
Farbrahmen
Porte-filtre
Portafiltros
Colour frame holder
Farbrahmenhalter
Glissière porte-filtre
Marco portafiltros
Beam focus knob
Fokussierknopf
Bouton de réglage du faisceau
Maneta de enfoque del haz
Lens tube
Linsentubus
Tube de lentille
Tubo de lentes
Barrel
Basisgehäuse
Corps
Tubo
Drop-in iris slot
Einschubfach für Irisblende
Logement d'iris amovible
Ranura para el iris
Shutters
Blenden
Couteaux
Cuchillas
Pattern holder slot
Einschubfach für Gobohalter
Logement de porte-gobo
Ranura del portagobos
Safety screen
Schutzgitter
Grille de protection
Rejilla de seguridad
Retainer bolt 2
Sicherungsschraube Nr. 2
Vis de retenue 2
Tornillo de fijación 2
Safety cable
(model #400SC)
Sicherungsseil
(Modell #400SC)
Câble de sécurité
(modèle #400SC)
Cable de seguridad
(modelo #400SC)
Retainer bolt 1
Sicherungsschraube Nr.1
Vis de retenue 1
Tornillo de fijación 1
Reflector
Reflektor
Réflecteur
Reflector
Yoke
Bügel
Lyre
Lira
Retaining clip
Sicherungsbügel
Clip de mantien
Clip de seguridad
Lamp housing
Lampengehäuse
Compartiment lampe
Cubierta de la lámpara
Reflector housing
Reflektorgehäuse
Compartiment réflecteur
Cubierta del reflector
Primary suspension yoke mounting holes
Hauptaufhängelöcher für Hängebügel
Trous de montage de la lyre de la suspension principale
Hoyos para el montaje de la lira de la suspensión primaria
CE Source Four

6CE Source Four

CE Source Four 7
English
CE Source Four instructions
Safety warnings
The CE Source Four high performance ellipsoidal spotlight is intended for
professional use only. Read entire
User Manual before using equipment.
Please note the following safety warnings before use:
Do not mount the CE Source Four on or near a flammable surface.
Use the luminaire in dry locations only, where humidity does not exceed 90
percent. Luminaire is not intended for outdoor use.
Mount and support the luminaire only by the primary suspension yoke holes.
Suspend the luminaire from a hook clamp or a stand mount, using a securely
tightened steel bolt (up to 12 mm Ø), washer and locking nut.
In addition to primary suspension, attach a safety cable (Model 400SC) or
chain to the secondary suspension point on the luminaire (see page 5).
Open all four shutters completely before turning the luminaire on.
Always hang the CE Source Four with the colour frame retaining clip in the
locked position.
Always replace the lamp if it becomes damaged or thermally deformed.
Keep the luminaire at least 0.7 meters away from anything it is shining on.
Lighted objects at this distance or greater will not exceed 90ºC temperature
from projected light.
Disconnect the unit from power before all cleaning and maintenance.
Maximum ambient temperature: T
a
=45 ° C
Maximum exterior surface temperature: T
max
=200ºC
A multilanguage label sheet is included with this manual. Affix the label of
the appropriate language over the existing warning label on the extension
yoke. Do not cover ETC trademark or CE mark.
Wiring and power information
A plug of at least 2.5 amp (220/240V) rating should be attached to the
luminaire's mains lead. The wires in the mains lead are 1.5mm 2 each and
coloured in accordance with the following code:
Green and Yellow: Earth
Blue: Neutral
Brown: Live
Warning: This luminaire must be earthed.
Current rating: 120V/5 amp maximum
240V/2.5 amp maximum
Operating frequency: 50/60Hz
t 180°c
0.7m

8CE Source Four
English
HPL lamps
HPL lamps are tungsten halogen lamps.
Important: Verify that the HPL lamp you use is suitable for the voltage at
your facility. 115-, 120-, 230-, and 240-volt HPL lamps are available.
Operating HPL lamps above their rated voltage reduces lamp life and can
cause premature lamp failure.
Warning: Do not use lamps other than the HPL in CE Source Four
luminaires. Use of lamps other than HPL will void CE safety conformity
and warranty.
Installing the HPL lamp
Important: The lamp must be installed before you use the luminaire.
Caution: Always replace the lamp if it becomes damaged or thermally
deformed.
1. Disconnect the unit from power before installing and replacing the lamp.
Warning: Let lamp cool before changing.
2. Loosen the knurled bolt on the back of the lamp housing and pull the
housing straight out.
3. Remove the HPL lamp from its box, holding it by the base.
Note: To avoid premature lamp failure, do not touch the lamp glass. If
you touch the lamp, clean it carefully with rubbing alcohol and a clean,
lint-free cloth before operation.
4. Line up the flat sides of the lamp base with the retention brackets on
either side of the socket. See figure 1.
5. Push down on the lamp base until the lamp seats firmly. (The top of the
lamp base will be even with the top edges of the retention brackets
when it is properly installed.)
Caution: Improperly installed lamps cause premature lamp failure and
socket problems.
6. Press lamp retainers down across lamp base and clip securely.
7. To reinstall the lamp housing, line up the side fins and the bolt hole, then
tighten the knurled bolt to secure the housing.
edocpmaLsttaWstloVpmetroloCefildetarevA
032/575LPH575032K˚002,3ruoh004
042/575LPH575042K˚002,3ruoh004
511/573LPH573511K
˚052,3ruoh003
X511/573LPH573511K˚050,3ruoh000,1
77/055LPH05577K˚052,3ruoh003
X77/055LPH05577K˚050,3ruoh000,2
511/575LP
H575511K˚052,3ruoh003
X511/575LPH575511K˚050,3ruoh000,2
021/575LPH575021K˚052,3ruoh003
Euro.
American
HPL lamp
Lamp
retention
brackets
Lamp housing
Knurled bolt
Figure 1
Lamp
retainers

CE Source Four 9
English
Aligning the lamp
Use the two concentric knobs on the rear of the lamp housing to align the
lamp. The outer knob centres the lamp within the reflector and locks it in
position; the inner knob fine tunes the field. See figure 1.
Important: Power must be on to align the lamp.
1. Unlock the outer knob by turning it anticlockwise one turn.
2. Gently push the outer knob from side to side and up and down until
the lamp is centred in the field.
3. Once the lamp is centred, tighten the outer knob to lock it in place.
4. Turn the inner knob right or left to adjust for optimum flat field.
Focusing the beam
1. Loosen the beam focus knob on the underside of the barrel. See
figure 2.
2. Slide the lens tube forward or backward to achieve the desired beam
edge. (For optimum gel life, set soft focus by moving the lens as shown
on table below.)
3. Once the luminaire is focused, tighten the beam focus knob.
Gel notes
For best results, always use a high quality, high temperature color medium.
ETC does not guarantee performance with low temperature, saturated color
gels.
ETC's Source Four gel frame holder extender may help increase your gel life.
Contact ETC or your dealer for ordering information.
Knurled
bolt
Lamp
housing
Peak and flat
adjustment
(inner knob)
Centre
adjustment
(outer knob)
Figure 1
Beam focus knob
Yoke
Bolt and spacer
Figure 2
Yoke locking knob
erutxiF
noisreV
sucoFtfoS
kcaBebuT
prahS
sucoF
sucoFtfoS
drawroFebuT
5°✔✔ ✔
01 °✔✔ ✔
91 °✘✔ ✔
62 °✘✔ ✔
63 °✔✔ ✘
05 °✘✔ ✔
✔= better gel life ✘ = worse gel life

10 CE Source Four
English
Shaping the beam
You may shape the beam with the shutters, a pattern, an optional drop-in
iris, and/or by rotating the barrel.
Pattern projection
The pattern holder slot is on the top side of the barrel, immediately in front
of the shutters. It accommodates A-size, B-size and glass pattern holders.
Use an optional donut (model #400DN) in the accessory holder to enhance
pattern projection. Donut diameter should be 64mm to 70mm for 19º
through 50º lenses.
Drop-in iris slot
The drop-in iris slot is on the top side of the front barrel, immediately in front
of the pattern holder slot. It accommodates either a drop-in iris or a
motorized pattern device. When it is not in use, a small sheet metal cover
secured with two crosshead screws prevents light leakage and retains the
iris assembly. To install an iris, follow these steps:
1. Use a crosshead screwdriver to loosen the screws on the drop-in iris
slot cover. Do not remove the screws.
2. Slide the cover completely forward, exposing the slot.
3. Insert the iris or motorized pattern device. If you install an iris, the flat
side must be toward the shutters and the iris handle should extend out
of slot.
4. Slide the slot cover back toward the shutters until it meets the iris
handle. Leave enough space to move the iris handle. Tighten the
screws.
Rotating the barrel assembly
1. Loosen the barrel rotation knob directly behind the shutters on the
underside of the reflector housing.
Caution: Do not remove the barrel rotation knob.
2. Rotate the barrel to the desired position (up to 25°in either direction
from centred position.)
3. Once the barrel is positioned, tighten the barrel rotation knob to lock it
into position.
Drop-in iris slot
Figure 2
Iris
Barrel rotation knob
Bolt 1 and spacer
Yoke
Beam focus knob
Figure 3
Bolt 2
A-size pattern holder
for 8cm diameter
patterns
B-size pattern holder
for 7cm and 6.3cm
diameter patterns
Figure 1
79mm
diameter
94 mm
70mm
diameter
94 mm