ETENON Fitness PC16 User manual

OWNER S MANUAL’
CAUTION
Please read all instructions in this manual before
use the equipment and keep the manual well.
Standing Calf Raise

In order void es and property dam sto a human injuri age , before th s of thise u e series
equipment please the following mportant notices, read i .
1. Before u fse o the e ent pleasequipm read this Owner’s Manual carefully The.
equipment should be assembled strictly following the relevantand used instructions
in this m and can not change an ponents oranual, y of its com
disassemble t f eelyi r .
2. It should ns ed thatbe e ur all e e b fully aware ty warnings andus rs hav een of the safe
precautions before they exercise on e e entth quipm .
3. Too loose-fitting clothing can not be worn and sports shoes should be t while, pu on
exercising.
4. The equipment should be a ly examined beforec reful training If there i ge. s dama ,
please do ot try o pair it by yourself Please ct yournot use it and do n t re . conta
supplier in time. It is necessary to inform af ert -sales service personnel as soon as
possible to get the ac repairedm hine .
5. Make sure the selector pin has fit well in its position before exercising and do not use
selector pin o ne coupled with th nt to o yther than the o is equipme av id an
injury.(Apply to le stationsing with cable)
6.
The equipment should be c indoors and make sure that thepla ed , ground s f ati l ,
and
there are spaceenough around uipment for s to c e o thethe eq u er exer is n
machine
freely.
7.
Before u t machine please check the cables to ensing he , sure that cable is in the
groove o ey and attention sh e paid ally tof pull , ould b especi the end f cableo . (Apply
to single t with cablesta ion )
8.
Only origina ched or m t rlly atta anufac ure provided w s ac can be used in thiseight t k
3

manufacturers’ weight stack plate. (Apply to single station w h bleit ca )
9. Child and ot lowed to be too lo t equipment while t s in usingpet are n al c se to he i i .
10. If exerciser feels dizzy or physical pain w ng he or should s ophile traini she t
exercising immediately and ult a d rcons octo .
11. The equipment should be ll d fined e and r dused in a we e plac unde well manage and
monitored t e equipment ownerway of h .
Before u t equipment please consult your physician ss expert andsing he and fitne ,
must be to read all tsure he if cations in this ownerspec i ’s manual Ma. nufacturer will
not be held responsible or y personal injury and property loss resulted from thef an
incorrect use t productsof he .
equipment and can not increase he eightt w of weight stack by use of other
4

Upper shield
Front shield
Floor stander
Adjusting bracket
Swing span
Shoulder pads
Bottom Frame
Foot
5

1. When strip f theo f wrappage around the surface of equipment, be a ,should c reful do
not hurt chine with knife atches on the surfacethe ma scr .
2. When moving this equipment a c ent number of personnel should be, suffi i used to
prevent the equipment from collision or to avoid the s caused by per nel, injurie son
shortage.
3. Prior to t of the equipment make sure that he p ts are ete noinstalla ion , all t ar compl ,
missing hardware.
4. When install the equipment s o or more s s working tog to, hould have tw per on ether
ensure the accurate location of parts assembly.
5. When install the equipment should pay attention to ssembly instructions tothe a
prevent component fitting to a w some om onents being omittedrong place or c p .
6.
The suitable in ation tool ould be used to avostall s sh id the equipment
damages or
human injuries c s by the use of appropriate tools in on processau ed in the installati .
7.
If need o ve equipment the movement must be af tion oft mo , ter the comple
installation The equipment can t e m he. no b oved w n he s lation process hat in tal sn’t
finished or locking hnut asn’t been ig tenedt h up.
8. Attention ce of fa c ing nut when the vshould be paid to the sequen stening lo k , o erall
installation of the quipment is no shed should no hten up the nut that ise t fini , t tig
being installed After the whole. machine is properly fitted the lotogether, cking nuts
can be tightened p o by oneu ne .
9.
Before st llation the cable rminals should hecked to make sure whetherin a te be c
they
are firm.
(Apply to ingle st tion bles a with ca )
10. After the completion of installation s rt t initial trial o he e ent with, ta he f t quipm gentle
6

the machine If something s is found with ment that. unu ual the equip , it is necessary
to check the equipment
carefully identify the probl s and, em reinstall it.
* : FramTen years Main es
* y : , , , eight p , , wiOne ear Bushings Pivot bearings guide rods W late cams s vel welding
parts Pull, -pin components
* ar: F , ubber gr , , .Half ye inish r ips belt cables
*Three Months upholstery:
force Make t that he t is w y normity before. cer ain t equipmen ithout an ab normally use
7

Assembly step1
Steps No. Description Specifications Qty
2Transverse joint frame 1
3Middle bottom Frame 1
38 Plain washer Φ24*Φ13*2.5 8
39 Spring washer M12 8
40 Hex socket head cap screw M12*30 8
59 Doorframe 1
1
8

Assembly step2
Steps No. Description Specifications Qty
1Front support frame 1
3Middle bottom Frame 1
4 Floor stander 1
41 Plain washer Φ20*Φ10.5*2 7
45 Spring washer M10 7
46 Hex socket head cap screw M10*30 5
47 Hex socket head cap screw M10*25 2
2
9

Assembly step3
Steps No. Description Specifications Qty
5 Load-bearing frame 1
6Swing span 1
7Adjusting bracket 1
14 Axle 2 1
16 Gas spring cylinder 1
41 Plain washer Φ20*Φ10.5*2 2
45 Spring washer M10 2
46 Hex socket head cap screw M10*30 2
3
10

Assembly step4
Steps No. Description Specifications Qty
1Front support frame 1
5 Load-bearing frame 1
6Swing span 1
13 Axle 1 1
51 Circlips for shaft Φ25 2
4
11

Assembly step5
Steps No. Description Specifications Qty
1Front support frame 1
3Middle bottom Frame 1
8 Foot frame 1
41 Plain washer Φ20*Φ10.5*2 2
43 Nylon insert lock nut M10 4
45 Spring washer M10 2
46 Hex socket head cap screw M10*30 2
48 Countersunk hex socket screws M10*70 4
5
12

Assembly step6
Steps No. Description Specifications Qty
6Swing span 1
10 Shoulder pads 2
52 Plain washer Φ16*Φ8.4*1.6 4
53 Spring washer M8 4
55 Hex socket head cap screw M8*25 4
6
13

Assembly step7
66
53
59
65
69
68
67
17
27
71
75
67
18
54
Steps No. Description Specifications Qty
17 20lb weight stack plate 13
18 Cable set 1
27 10lb counterweight 1
53 Spring washer M8 2
54 Hex socket head cap screw M8*20 2
59 Doorframe 1
65 Guild rod stator 1
66 Big washer Φ24*Φ8.4*2 2
67 Rod end cover 4
68 Rubber bumper 2
70 Cage nut M8 2
71 Rubber bumper Φ38*Φ22*8 2
75 Guide rod 2
7
14

Assembly step8
52
54
79
59
78
77
77
60
78
61
Steps No. Description Specifications Qty
52 Plain washer Φ16*Φ8.4*1.6 10
54 Hex socket head cap screw M8*20 8
59 Doorframe 1
60 Upper shield 1
61 Shield fixation column 2
77 Hex socket head cap screw M6*16 6
78 Plain washer Φ12*Φ6.4*1.6 6
79 Front shield 1
8
15

16
Cable Route Diagram
Correct Wrong
L plate
L plate

Exploded View
17

Exploded List
18
No. Description Specifications Qty
1Front support frame 1
2Transverse joint frame 1
3Middle bottom Frame 1
4 Floor stander 1
5 Load-bearing frame 1
6Swing span 1
7Adjusting bracket 1
8 Foot frame 1
9 Adjusting bolt column 1
10 Shoulder pads 2
11 Adjustment handle bracket 1
12 Small shaft 1
13 Axle 1 1
14 Axle 2 1
15 Nylon rollers 1
16 Gas spring cylinder 1
17 20lb weight stack plate 13
18 Cable set 1
19 Steps rolling bearing 4
20 Knuckle bearing M10 1
21 Spring 1
22 M20 nut 1
23 Copper-based bushing Φ16*Φ13*11.5 2
24 Reed nut HLM-GB25 3
25 Washer Φ25.4*Φ11*5 2
26 Roller link head
27 10lb counterweight 1
28 Rubber bumper 1
29 Limiting rubber 2
30 Pulley 7
31 Handle grip 3
32 Tube stopper □50*70*3 4
33 End cover Φ25*21（gray）2
34 End ring Φ25*14（gray）2
35 End ring Φ25*14（yellow）1
36 End cover Φ25*21（yellow）1
37 Rubber mat 4
38 Plain washer Φ24*Φ13*2.5 8
39 Spring washer M12 8
40 Hex socket head cap screw M12*30 8
41 Plain washer Φ20*Φ10.5*2 33
42 Hex socket head cap screw M10*50 7

Exploded List
No. Description Specifications Qty
43 Nylon insert lock nut M10 12
44 Hex socket head cap screw M10*75 1
45 Spring washer M10 11
46 Hex socket head cap screw M10*30 11
47 Hex socket head cap screw M10*25 2
48 Countersunk hex socket screws M10*70 4
49 Countersunk hex socket screws M6*25 3
50 Slotted set screws with cone point M4*5 3
51 Circlips for shaft Φ25 4
52 Plain washer Φ16*Φ8.4*1.6 10
53 Spring washer M8 10
54 Hex socket head cap screw M8*20 8
55 Hex socket head cap screw M8*25 4
56 Hex socket head cap screw M5*50 1
57 Nylon insert lock nut M5 1
58 14holes shaft 1
59 Doorframe 1
60 Upper shield 1
61 Shield fixation column 2
62 Rubber mat 4
63 Hexagon socket button head screw M8*16 8
64 Pulley catch 1
65 Guild rod stator 1
66 Big washer Φ24*Φ8.4*2 2
67 Rod end cover 4
68 Rubber bumper 2
69 Selector pin 1
70 Cage nut M8 2
71 Rubber bumper Φ38*Φ22*8 2
72 Shield fixation plate 2
73 Cross recess pan head self-tapping screw ST4.2*13 4
74 Stopple Φ10*8.5 1
75 Guide rod 2
76 Spring pin 10*45 1
77 Hex socket head cap screw M6*16 6
78 Plain washer Φ12*Φ6.4*1.6 6
79 Front shield 1
80 Guide sleeve 2
81
82
83
84
19

( )Basic Maintenance
1. Clean the seat pad b ck pad and cushion with ater and soft cloth order, a warm w in
to avoid s ethe w at erosion t s componento the e .
2. Clean the frame with warm water and soft cloth.
3. Cleaning chrome at parts wipe them hol moistened o t c thpl ed : with alco s f lo .
( ainte )Basic M nance
1. Check t m ssion cab k the ght ss and s on of erans i le. Chec ti ne abra i the cabl
( sur e, , di s on).disrepair of the fac bend stortion and o (Apply to sing stat withle ion
cable)
2.
Check guide and wipe it with s er cloth and alcohol and l c itrod, oft dust , ubri ate
by
anticorrosive oil but please don, ’t let e c s ve a c ulated on rodx es i oil c um .
(Apply to
single s at tion with cable)
3.
Check w t stack to any damagedeigh know if there is steel plate which caused by
too much force or friction on rod.
(Apply to sing tat with cablele s ion )
4.
Check pulley on whether its groove surface is clean and whether it runs
smoothly.
(Apply t ion witho single stat cable)
5.
Check bol ng p ts W m with alcohol and anticorrosive oilts and fixi ar . ipe the .
1.
Check w olts on ba c frame e l ose springshether b si becom o , have damaged and
the
tightness of drive cable.
2.
Check if there is rust or paint loss on main frame and basic rack clean out rust, ,
by
sand paper nd then cover i t same color paint from he s e supplier, a t wi h t am .
3.
Clean and c te e p elubri a ev ry bearing, and kee quipment ork smoothlyw .
4.
Check w t oil cylinder suffers oil leakagehether he .
20