ETENON Fitness PC2001 User manual

OWNER S MANUAL’
CAUTION
Please read all instructions in this manual before
use the equipment and keep the manual well.
CHEST PRESS

1

2

Equipment Schematic
3
right arm frame
left arm frame
back pad
Door Frame
set pad
main stand frame

4

5

Assembly step 1
6
Step No. Description Specifications Qty
1 Door Frame 1
20 Inner Hexagon Socket Head Bolt M10*35 4
24 Spring washer M10 4
27 Flat washer Φ20*Φ10.5*2 4
40 main stand frame 1
41 ground connection frame 1
47 cable 2 1
72 pulley φ114*25.8 1
83 socket cap screw M10*25 1
84 socket cap screw M10*35 3
85 socket cap screw M10*50 1
89 spring washer M10 4
92 flat washer Φ20*Φ10.5*2 6
94 nut M10 1
1

Assembly step 2
7
E
Step No. Description Specifications Qty
42 left arm frame 1
43 right arm frame 1
46 cable 1 1
47 cable 2 1
49 bumping post 1 1
50 bumping post 2 2
51 Single hole square plate 3
65 end cover φ59.5*φ11*14 2
66 decorative ring φ59.5*6 2
67 pulley cover 125*125*22*3 3
70 wide pulley φ116*47 2
72 pulley φ114*25.8 1
82 Cap socket screw M10*25 2
84 socket cap screw M10*35 2
85 socket cap screw M10*50 1
86 socket cap screw M10*70 2
89 spring washer M10 6
92 flat washer Φ20*Φ10.5*2 1
94 nut M10 1
2
The slotting is facing down.
(The installation of all pulley
covers are same.)

Assembly step 3
8
Step No. Description Specifications Qty
44 seat adjustment rack 1
56 stop screw M10*18*φ8 1
73 Semi-sliding sleeve group 2
81 socket cap screw M8*30 6
88 spring washer M8 6
89 spring washer M10 1
91 flat washer Φ16*Φ8.4*1.6 6
95 set pad 1
96 back pad 1
3

Assembly step 4
9
Step No. Description Specifications Qty
4 Guide rod 2
5 Guide rod fixed plate 1
9 Rubber bumper φ64*φ32*φ20*35 2
10 Rubber bumper φ38*φ21*10 2
12 Rod end cover 4
13 Pulley sets φ89*32 2
14 Selector pin 1
19 Inner Hexagon Socket Head Bolt M8*20 2
21 Inner Hexagon Socket Head Bolt M10*55 2
23 Spring washer M8 2
26 Flat washer Φ16*Φ8.4*1.6 2
27 Flat washer Φ20*Φ10.5*2 4
28 Nylon nut M10 2
62 10lb top weight assembly 1
63 10lb weight stack assembly 9
4

Assembly step 5
10
Step No. Description Specifications Qty
2 Upper shield 1
3 Shield fixed plate 4
6 Fixed bushing 12
7 Front shield 1
8 Back shield 1
15 cross recessed countersunk head screw M5*10 8
16 Countersunk head hexagon socket screw M6*16 12
18 Inner Hexagon Socket Head Bolt M6*16 2
22 Spring washer M6 2
25 Flat washer Φ12*Φ6.4*1.6 2
5

11
CABLE ROUTING DIAGRAM
Cable
limiting post
Correct Wrong
Cable
limiting post

Exploded View
12

13
Exploded List
No. Description Specifications Qty
1 Doorframe 1
2 Upper shield 1
3 Shield fixed plate 4
4 Guide rod 2
5 Guide rod fixed plate 1
6 Fixed bushing 12
7 Front shield 1
8 Back shield 1
9 Rubber bumper φ64*φ32*φ20*35 2
10 Rubber bumper φ38*φ21*10 2
11 Floor cushion 2
12 Rod end cover 4
13 Pulley sets φ89*32 2
14 Selector pin 1
15 cross recessed countersunk head screw M5*10 8
16 Countersunk head hexagon socket screw M6*16 12
17 Inner Hexagon Mushroom Head Bolt M8*25 4
18 Inner Hexagon Socket Head Bolt M6*16 2
19 Inner Hexagon Socket Head Bolt M8*20 2
20 Inner Hexagon Socket Head Bolt M10*35 4
21 Inner Hexagon Socket Head Bolt M10*55 2
22 Spring washer M6 2
23 Spring washer M8 2
24 Spring washer M10 4
25 Flat washer Φ12*Φ6.4*1.6 2
26 Flat washer Φ16*Φ8.4*1.6 6
27 Flat washer Φ20*Φ10.5*2 8
28 Nylon nut M10 2
29 Rivet nut with small countersunk head M8*18 4
30
31
32
33
34
35
36
37
38
39
40
41
42

14
Exploded View

Exploded List
15
No. Description Specifications Qty
40 main stand frame 1
41 ground connection frame 1
42 left arm frame 1
43 right arm frame 1
44 seat adjustment rack 1
45 back cushion adjustment rack 1
46 cable 1 1
47 cable 2 1
48 Two hole connecting plate 2
49 bumping post 1 1
50 bumping post 2 2
51 Single hole square plate 3
52 aluminum end cover Φ6.5*Φ38*13 2
53 alumium ring Φ23*Φ26*Φ32*14.5 2
54 alumium ring Φ26*Φ35*13 2
55 spring nut M6*Φ20.8*10 2
56 stop screw M10*18*φ8 2
57 adjustment handle 2
58 fixed axis 2
59 torsion spring 2
60 12 hole selection axis 1
61 elastic cylindrical pin φ10*45 1
62 10lb top weight assembly 1
63 10lb weight stack assembly 11
64 plastic ring Φ26*Φ30*4.5 2
65 end cover φ59.5*φ11*14 2
66 decorative ring φ59.5*6 2
67 pulley cover 125*125*22*3 7
68 rubber handle gloves φ31.5*φ24*178 2
69 floor mat 2
70 wide pulley φ116*47 2
71 crash pad 2
72 pulley φ114*25.8 4
73 Semi-sliding sleeve group 4
74 elliptical pipe plug 2
75 Step rolling bearing 4
76 Rod end joint bearing 2
77 split washer d0=6 4
78 Set screw for inner hexagon end M5*5 4
79 socket cap screw M6*25 4
80 Socket head cap screw M8*25 4
81 socket cap screw M8*30 6

Exploded List
16
No. Description Specifications Qty
82 Cap socket screw M10*25 2
83 socket cap screw M10*25 1
84 socket cap screw M10*35 5
85 socket cap screw M10*50 4
86 socket cap screw M10*70 2
87 spring washer M6 2
88 spring washer M8 6
89 spring washer M10 12
90 flat washer Φ12*Φ6.4*1.6 2
91 flat washer Φ16*Φ8.4*1.6 10
92 flat washer Φ20*Φ10.5*2 9
93 Rivet nut with small countersunk head M8*18 4
94 nut M10 4
95 set pad 1
96 back pad 1
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123

17

Weight stack label instructions
1 Wipe front surface of weight stack
2 Peel off back sheet adhesive side from label and make sure
that the label remains attached to the application tape
3 Aline the center hole of label with the weight stack
4 Line up the first label to hole on top plate
5 Make sure label is straight and slowly press into place
6 Gently remove application tape and rub each label firmly against
the weight stack
7 Allow labels to stand for 24 hours to allow adhesive to cure fully
..
. ()
.
..
..
..
.
.
..
center hole

bsl
80
bsl
110
bsl
100
bsl
90
bsl
50
bsl
40
bsl
30
bsl
20
lbs
10
bsl
70
bsl
60
gk
36 3.
gk
gk
gk
40 8.
gk
22 7.
Kg
18 1.
gk
13 6.
gk
9 1.
kg
4 5.
gk
31 8.
gk
27 2.
45 4.
bsl
120
gk
49 9.
54 4.
bsl
80
bsl
110
bsl
100
bsl
90
bsl
50
bsl
40
bsl
30
bsl
20
lbs
10
bsl
70
bsl
60
gk
36 3.
gk
gk
gk
40 8.
gk
22 7.
Kg
18 1.
gk
13 6.
gk
9 1.
kg
4 5.
gk
31 8.
gk
27 2.
45 4.
bsl
120
gk
49 9.
54 4.