ETENON Fitness PTT0224 User manual

Roman Chair
OWNER S MANUAL'

Cautions
In order to avoid human injuries and property damages,before the use of this series
equipment please read the following important notices
1 Before use of the equipment please read this Owner’s Manual carefully The
equipment should be assembled and used strictly following the relevant instructions
in this manual and can not change any of its components or disassemble it freely
2. It should be ensured that all users have been fully aware of the safety warnings and
precautions before they exercise on the equipment
3 Too loose fitting clothing can not be worn, and sports shoes should be put on while
exercising
4. The equipment should be carefully examined before training If there is damage
please do not use it and do not try to repair it by yourself Please contact your
supplier in time It is necessary to inform after-sales service personnel as soon as
possible to get the machine repaired
5. The equipment should be placed indoors and make sure that the ground is flat and
there are enough space around the equipment for user to exercise on the machine
freely.
6. Child and pet are not allowed to be too close to the equipment while it is in using
7. If exerciser feels dizzy or physical pain while training he or she should stop
exercising immediately and consult a doctor
8. The equipment should be used in a well defined place and under well managed and
monitored way of the equipment owner
,.
. .
,.
.
.-
.
.,
.
.
.
,,
.
.
.
2

Before using the equipment please consult your physician and fitness expert and
must be sure to read all the specifications in this owner s manual Manufacturer will
not be held responsible for any personal injury and property loss resulted from the
incorrect use of the products
,
’.
.
3

Fitting Instructions
1 When strip off the wrappage around the surface of equipment should be careful do
not hurt the machine with knife scratches on the surface
2 When moving this equipment a sufficient number of personnel should be used to
prevent the equipment from collision or to avoid the injuries caused by personnel
shortage
3 Prior to installation of the equipment make sure that all the parts are complete no
missing hardware
4 When install the equipment should have two or more persons working together to
ensure the accurate location of parts assembly
5 When install the equipment should pay attention to the assembly instructions to
prevent component fitting to a wrong place or some components being omitted
6 The suitable installation tools should be used to avoid the equipment damages or
human injuries caused by the use of inappropriate tools in the installation process
7. If need to move equipment the movement must be after the completion of
installation The equipment can not be moved when the installation process hasn’t
finished or locking nut hasn’t been tightened up.
8. Attention should be paid to the sequence of fastening locking nut when the overall
installation of the equipment is not finished should not tighten up the nut that is
being installed After the whole machine is properly fitted together the locking nuts
can be tightened up one by one.
10. After the completion of installation start the initial trial of the equipment with gentle
force Make certain that the equipment is without any abnormity before normally use
the machine If something unusual is found with the equipment that it is necessary
. ,,
.
.,
,
.
., ,
.
.,
.
.
.
.
.
,
.
,
,
.,
,
.
.,
4

to check the equipment carefully identify the problems and reinstall it
Ten years Main Frames
One year Bushings Pivot bearings guide rods Weight plate cams swivel welding
parts Pull-pin components
Half year: Finish rubber grips belt cables
Three Months upholstery
,.
*:
* : , , , ,,
,
* , ,, .
*:
Warranty
5

Assembly step 1
6
Steps No. Description Specifications Qty
1 Intermediate support frame 1
2 Right support frame 1
3 Left support frame 1
44 Hex socket head cap screw M12*140 2
47 Plain washer Φ24*Φ13*2.5 4
52 Nylon insert lock nut M12 2
1

Assembly step 2
7
Steps No. Description Specifications Qty
2 Right support frame 1
3 Left support frame 1
6 Mainframe 1
7 Leg pad fixing frame φ25*124 1
33 Circlips for shaft d0=25 2
2

Assembly step 3
8
53
Steps No. Description Specifications Qty
6 Mainframe 1
12 Foot frame 1
42 Hex socket head cap screw M10*80 2
46 Plain washer Φ20*Φ10.5*2 4
51 Nylon insert lock nut M10 2
53 Foot plate 1
3

Assembly step 4
9
Steps No. Description Specifications Qty
6 Mainframe 1
8 Arc adjusting plate 1
25 Limiting rubber φ20*17*M8 2
39 Hexagon socket button head screw M8* 20 2
41 Hex socket head cap screw M10*30 2
45 Plain washer Φ16*Φ8.4*1.6 2
46 Plain washer Φ20*Φ10.5*2 4
48 Spring washer M8 2
51 Nylon insert lock nut M10 2
4

Assembly step 5
10
Steps No. Description Specifications Qty
2 Right support frame 1
6 Mainframe 1
19 Gas spring φ22*330（55KG）1
45 Plain washer Φ16*Φ8.4*1.6 2
50 Nylon insert lock nut M8 2
5

Assembly step 6
11
Steps No. Description Specifications Qty
6 Mainframe 1
9 Adjusting tube 1
18 Limiting screw M10*25*φ8 1
49 Spring washer M10 1
6

Assembly step 7
12
Steps No. Description Specifications Qty
5 Cushion frame 1
9 Adjusting tube 1
43 Hex socket head cap screw M10*90 2
46 Plain washer Φ20*Φ10.5*2 4
51 Nylon insert lock nut M10 2
7

Assembly step 8
Steps No. Description Specifications Qty
5 Cushion frame 1
13 Back pad 2
40 Hexagon socket button head screw M8* 30 4
45 Plain washer Φ16*Φ8.4*1.6 4
48 Spring washer M8 4
8
13
40

Assembly step 9
Steps No. Description Specifications Qty
4 Pedal frame 1
6 Mainframe 1
26 End cap Φ50*Φ9*15 1
38 Countersunk hex socket screws M8*25 1
39 Hexagon socket button head screw M8*20 1
45 Plain washer Φ16*Φ8.4*1.6 1
48 Spring washer M8 1
9
14

Assembly step 10
Steps No. Description Specifications Qty
12 Foot frame 1
14 Leg pad 4
26 End cap Φ50*Φ9*15 4
38 Countersunk hex socket screws M8*25 4
10
15

Exploded View
16

Exploded List
17
No. Description Specifications Qty
1 Intermediate support frame 1
2 Right support frame 1
3 Left support frame 1
4 Pedal frame 1
5 Cushion frame 1
6 Mainframe 1
7 Leg pad fixing frame φ25*124 1
8 Arc adjusting plate 1
9 Adjusting tube 1
10 Adjusting column 1
11 Semi-sliding sleeve 1
12 Foot frame 1
13 Back pad 2
14 Leg pad 4
15 Steps rolling bearing φ52*φ25*18 2
16 Spring Φ1.4*Φ12.5*30 1
17 Nut R-C-7001-02 1
18 Limiting screw M10*25*φ8 1
19 Gas spring φ22*330（55KG）1
20 Pop pin knob 1
21 Handle grip Φ37.5*Φ31*175 2
22
23
24 Semi-sliding sleeve 1
25 Limiting rubber φ20*17*M8 2
26 End cap Φ50*Φ9*15 4
27 Rubber mat 2
28 pedal cover 2
29 Elliptical tube stopper 2
30 Affixed to shackle 2
31 Rotary knob 1
32 reed nut M6*27.2*15 2
33 Circlips for shaft d0=25 2
34 Countersunk riveted nut M8*16.5 4
35
36
37 Countersunk hex socket screws M6*10 4
38 Countersunk hex socket screws M8*25 8
39 Hexagon socket button head screw M8*20 3
40 Hexagon socket button head screw M8*30 4
41 Hex socket head cap screw M10*30 2
42 Hex socket head cap screw M10*80 2

Exploded List
18
No. Description Specifications Qty
43 Hex socket head cap screw M10*90 2
44 Hex socket head cap screw M12*140 2
45 Plain washer Φ16*Φ8.4*1.6 9
46 Plain washer Φ20*Φ10.5*2 14
47 Plain washer Φ24*Φ13*2.5 4
48 Spring washer M8 7
49 Spring washer M10 1
50 Nylon insert lock nut M8 2
51 Nylon insert lock nut M10 8
52 Nylon insert lock nut M12 2
53 Foot plate 1
54 Countersunk hex socket screws M10*25 2
55 Aluminum end cover Φ45*Φ6.5*14 2
56 Aluminum ring Φ39*Φ30*14.5 2
57 Aluminum ring Φ42*Φ33*13 2
58 Plastic ring Φ37*Φ33*4.5 2
59 Hex socket head cap screw M5*5 4
60 Hex socket head cap screw M6*25 2
61 Spring washer M6 2
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84

Maintenance Attentions
Daily Maintenance
Further Maintenance
(Basic Maintenance)
1 Clean the seat pad back pad and cushion with warm water and soft cloth in order
to avoid the sweat erosion to these component
2. Clean the frame with warm water and soft cloth.
3. Cleaning chrome plated parts wipe them with alcohol moistened soft cloth
1. Check whether bolts on basic frame become loose springs have damaged and
the tightness of drive cable
2. Check if there is rust or paint loss on main frame and basic rack clean out rust by
sand paper, and then cover it with same color paint from the same supplier
3. Clean and lubricate every bearing, and keep equipment work smoothly
4. Check whether the rubber gasket is broken.
5. Check bolts and fixing parts Wipe them with alcohol and anticorrosive oil
.,
.
:.
,
.
,,
.
.
..
19