ETENON Fitness PTT0220 User manual

Roman Chair
OWNER S MANUAL'

Cautions
In order to avoid human injuries and property damages,before the use of this series
equipment please read the following important notices
1 Before use of the equipment please read this Owner’s Manual carefully The
equipment should be assembled and used strictly following the relevant instructions
in this manual and can not change any of its components or disassemble it freely
2. It should be ensured that all users have been fully aware of the safety warnings and
precautions before they exercise on the equipment
3 Too loose fitting clothing can not be worn, and sports shoes should be put on while
exercising
4. The equipment should be carefully examined before training If there is damage
please do not use it and do not try to repair it by yourself Please contact your
supplier in time It is necessary to inform after-sales service personnel as soon as
possible to get the machine repaired
5. The equipment should be placed indoors and make sure that the ground is flat and
there are enough space around the equipment for user to exercise on the machine
freely.
6. Child and pet are not allowed to be too close to the equipment while it is in using
7. If exerciser feels dizzy or physical pain while training he or she should stop
exercising immediately and consult a doctor
8. The equipment should be used in a well defined place and under well managed and
monitored way of the equipment owner
,.
. .
,.
.
.-
.
.,
.
.
.
,,
.
.
.
2

Before using the equipment please consult your physician and fitness expert and
must be sure to read all the specifications in this owner s manual Manufacturer will
not be held responsible for any personal injury and property loss resulted from the
incorrect use of the products
,
’.
.
3

Fitting Instructions
1 When strip off the wrappage around the surface of equipment should be careful do
not hurt the machine with knife scratches on the surface
2 When moving this equipment a sufficient number of personnel should be used to
prevent the equipment from collision or to avoid the injuries caused by personnel
shortage
3 Prior to installation of the equipment make sure that all the parts are complete no
missing hardware
4 When install the equipment should have two or more persons working together to
ensure the accurate location of parts assembly
5 When install the equipment should pay attention to the assembly instructions to
prevent component fitting to a wrong place or some components being omitted
6 The suitable installation tools should be used to avoid the equipment damages or
human injuries caused by the use of inappropriate tools in the installation process
7. If need to move equipment the movement must be after the completion of
installation The equipment can not be moved when the installation process hasn’t
finished or locking nut hasn’t been tightened up.
8. Attention should be paid to the sequence of fastening locking nut when the overall
installation of the equipment is not finished should not tighten up the nut that is
being installed After the whole machine is properly fitted together the locking nuts
can be tightened up one by one.
10. After the completion of installation start the initial trial of the equipment with gentle
force Make certain that the equipment is without any abnormity before normally use
the machine If something unusual is found with the equipment that it is necessary
. ,,
.
.,
,
.
., ,
.
.,
.
.
.
.
.
,
.
,
,
.,
,
.
.,
4

to check the equipment carefully identify the problems and reinstall it
Ten years Main Frames
One year Bushings Pivot bearings guide rods Weight plate cams swivel welding
parts Pull-pin components
Half year: Finish rubber grips belt cables
Three Months upholstery
,.
*:
* : , , , ,,
,
* , ,, .
*:
Warranty
5

Assembly step 1
6
Steps No. Description Specifications Qty
1main frame 1
2left support frame 1
3right support frame 1
4foot pedal frame 1
18 Hex Socket Head Cap screw M10*80 2
19 Hex Socket Head Cap screw M12*80 3
26 flat washer Φ20*Φ10.5*2 4
27 flat washer Φ24*Φ13*2.5 6
30 nut M10 2
31 nut M12 3
1
18
26
30

Assembly step 2
7
Steps No. Description Specifications Qty
5 cushion frame 1
20 Hex Socket Head Cap screw M10*90 2
26 flat washer Φ20*Φ10.5*2 4
30 nut M10 2
2

Assembly step 3
8
Steps No. Description Specifications Qty
12 end cover 2
17 Hexagon Socket Button Head Screw M8*30 4
22 Inner Haxagon Sunk Head Bolt M8*25 2
25 flat washer Φ16*Φ8.4*1.6 4
28 spring washer M8 4
33 leg pad 2
44 Back pad 2
3

Exploded View
12

Exploded List
13
No. Description Specifications Qty
1 main frame 1
2 left support frame 1
3 right support frame 1
4 foot pedal frame 1
5 cushion frame 1
6 adjusting tube 1
7
8 half sliding cover 1
9
10 limiting screw 1
11 half sliding cover 1
12 end cover 2
13
14
15 through-hole handle cover 2
16 ground mattress 4
17 Hexagon Socket Button Head Screw M8*30 4
18 Hex Socket Head Cap screw M10*80 2
19 Hex Socket Head Cap screw M12*80 3
20 Hex Socket Head Cap screw M10*90 2
21
22 Inner Haxagon Sunk Head Bolt M8*25 2
23
24 reed nut M6*Φ27.2*15 2
25 flat washer Φ16*Φ8.4*1.6 4
26 flat washer Φ20*Φ10.5*2 10
27 flat washer Φ24*Φ13*2.5 6
28 spring washer M8 4
29 spring washer M10 1
30 nut M10 6
31 nut M12 3
32 stopper 4
33 leg pad 2
34 foot pedal 1
35 Inner Haxagon Sunk Head Bolt M10*25 2
36 aluminum end cover 2
37 aluminum ring 2
38 aluminum baffle ring 2
39 plastic cup 2
40 hexagon socket set screws with cone end M5*5 4
41 Hex Socket Head Cap screw M6*25 2
42 spring washer M6 2
43 round knob 1
44 Back pad 2

Maintenance Attentions
Daily Maintenance
Further Maintenance
(Basic Maintenance)
1 Clean the seat pad back pad and cushion with warm water and soft cloth in order
to avoid the sweat erosion to these component
2. Clean the frame with warm water and soft cloth.
3. Cleaning chrome plated parts wipe them with alcohol moistened soft cloth
1. Check whether bolts on basic frame become loose springs have damaged and
the tightness of drive cable
2. Check if there is rust or paint loss on main frame and basic rack clean out rust by
sand paper, and then cover it with same color paint from the same supplier
3. Clean and lubricate every bearing, and keep equipment work smoothly
4. Check whether the rubber gasket is broken.
5. Check bolts and fixing parts Wipe them with alcohol and anticorrosive oil
.,
.
:.
,
.
,,
.
.
..
14