Euro Video EV-D1660 User manual

Digital VideoRecorder
User Manual
EV-D1660
Please read this instructions thoroughly before operation and re tain it
for future reference.
November 2004 V 1.2
www.eurovideo - cctv.com
www.eurovideo - cctv.com

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert
the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that
may be of sufficient magnitude to c onstitute a risk of electric shock to persons.
The exclamation point within an equ ilateral triangle is intended to alert the user to the presence
of important operating and maintena nce - (servicing) instructions in the literature accompanying
the appliance.
All the safety and operating instructions should be read before operation. The improper operation may cause
permanent damage.
Please use the provided adaptor (Other adaptor is not suitable for this machine).
Please lift and place this equipment gently.
Do not expose this equipment to open sunlight.
Do not use this equipment near water or in contact with water.
Do not spill liquid of any kind on the equipment.
Please power down the unit before unplugging.
Do not switch the Power On & Off within short period of time ( within 3 seconds).
Do not attempt to service this equipment by yourself.
Installation should be made by qualified service personnel.
WARNING
1
www.eurovideo - cctv.com

2
What do you get
What do you get
?
?
FEATURES ---------------------------------------------------------------- ------------------------
PACKAGE INCLUDING ---------------------------------------------------------------- --------
Before Operation
Before Operation
INSTALLATION GUIDE ---------------------------------------------------------------- --------
FRONT PANEL ---------------------------------------------------------------- -------------------
BACK PANEL ---------------------------------------------------------------- ---------------------
Basic Operation
Basic Operation
START THIS UNIT ---------------------------------------------------------------- ----------------
OPERATION ---------------------------------------------------------------- ------------------------
Detailed Menu Setup
Detailed Menu Setup
ACCESS MENU ---------------------------------------------------------------- ------------------
MAIN MENU ---------------------------------------------------------------- -----------------------
MENU OPTIONS ---------------------------------------------------------------- -----------------
MOTION DETECTION ---------------------------------------------------------------- ----------
Advanced Operation
Advanced Operation
OPERATION OPTIONS ---------------------------------------------------------------- --------
KEY LOCK ---------------------------------------------------------------- ------------------------
RS - 232 PROTOCOL ---------------------------------------------------------------- ------------
Trouble Shooting ---------------------------------------------------------------- ------------------
Specifications ---------------------------------------------------------------- ----------------------
APPENDIX #1 INSTALLING THE HDD ----------------------------------------------------
APPENDIX #2 PIN CONFIGURATIONS ---------------------------------------------------
APPENDIX #3 RACK MOUNT - ---------------------------------------------------------------
APPENDIX #4 RECORDING SPEED -------------------------------------------------------
TABLE OF CONTENTS
3
3
4
5
7
8
8
10
10
11
15
17
18
18
19
19
20
22
24
25
www.eurovideo - cctv.com

FEATURES
DVR Features
Wavelet Compression Format replaces Time - Lapse VCR + Multiplexer
4 Audio inputs / 2 Audio outputs
On Screen Display and RTC (Real time clock) Function
Support from 4 channel to 7/9/10/13/16 channels video inputs
Picture - In - Picture (PIP) is available in live and DVR playback modes
Motion detection function and 4 Level video quality adjustable on each channel
Alarm Input & Output Function
Video loss detected on each channel can record 160 events
Power - loss memory function
Support 2 Removable HDDs , IDE Type
Quick Multiple Search by date/time, alarm, full list
Security password protection
RS - 232, RS - 485 communication protocol
3
What do you get ?
Digital Video Recorder with HDD cartridge)
User Manual
2 Keys for Cartridge
Power Adapter and Cord
NOTE : Please check the package to make sure that you receive th e complete accessories which includes the
components shown above.
Accessories pack
PACKAGE INCLUDING
www.eurovideo - cctv.com

4
1. Connect cameras and monitor with the DVR.
2. Shown below is one example for connecting the DVR to your exi sting Observation System.
3. Install HDDs (The compatible HDD Brands are listed in the following table.)
Please refer to page.20 Appendix #1 for installation instruction s.
The HDDs must be installed before turning on the DVR.
INSTALLATION GUIDE Before Operation
Manufacturer Model Capacity Rotation
HITACHI Deskstar 180 GXP (120 GB) 120GB 7200 rpm
HITACHI Deskstar 7K250, HDS722516VLAT20
160GB
7200rpm
HITACHI Deskstar 7K250, HDS722525VLAT80 250GB 7200rpm
IBM Deskstar 120GXP (80GB) 80GB 7200 rpm
IBM Deskstar 120GXP (120GB) 120GB 7200 rpm
Maxtor DiamondMax 536DX(60GB) 4W060H4 60GB 5400rpm
Maxtor DiamondMax Plus 9 80GB 7200 rpm
Maxtor DiamondMax Plus 9, Model#6Y120L 120GB 7200 rpm
Maxtor DiamondMax Plus 9, Model#6Y160L0 160GB 7200rpm
Seagate Barracuda ATA IV, ST380021A 80GB 7200rpm
Seagate Barracuda ATA V, ST3120023A 120GB 7200 rpm
Seagate Barracuda 7200.7 Plus, ST3160023A 160GB 7200 rpm
Western Digital Caviar WD1200BB-00CAA1 120GB 7200rpm
Western Digital Caviar WD2000BB-00DWA0 200GB 7200rpm
COMPATIBLE HARD DISK BRANDS
www.eurovideo - cctv.com

5
FRONT PANEL
1. REMOVABLE HDD CARTRIDGE
Please refer to page.20 Appendix #1.
2. MENU
Press MENU to enter main menu.
3. ENTER
Press ENTER for confirmation.
4. ZOOM
Press ZOOM to enlarge the picture display.
5.
Press PIP button for Picture in Picture screen.
6. SLOW
To slow down speed of play mode.
7. SELECT
Press the Select to select appointed camera (1~16) to display on full screen mode.
8.
4 channels disp0lay mode
www.eurovideo - cctv.com

6
9.
7, 9, 10, 13 channels display mode
10.
16 channels display mode
11. LED LIGHT
The LED Light is ON under following condition.
HDD : HDD is activated
HDD Full : HDD is full
ALARM : If you want to turn off the ALARM LED light, please refe r to page.14 and set the
Camera / ALARM item as OFF. (all of the cameras should be set as OFF.)
TIMER : When Timer is set as Enabled
PLAY : On Play mode
REC : On Recording mode
12. CAMERA (1 - 16)
Press the Camera Select (1 - 16) to select specified camera.
13. REC
Press REC to start recording.
14. REW / LEFT
REW : Under DVR play mode, it can play video backward at different spe eds. (Press REW again to adjust
speed as 1, 2, 4, 8, 16, 32 times)
Left : Under setup mode, it works as Left button.
15. PLAY
Press PLAY to play recorded video.
16. STOP / DOWN
STOP : Under DVR Record / Play mode, it can stop the moment acti on.
DOWN : Under setup mode, it works as Down button.
17. PAUSE / UP
Pause : Under DVR play mode, it can pause the action.
UP : Under setup mode, it works as Up button.
18. FF / Right
FF : It can play video forward at high speed, and press FF again to adjust speed from 1, 2, 4, 8, 16, 32 times.
Right : Under setup mode, it can work as Right button.
19. POWER
Press Power to turn ON / OFF the DVR.
www.eurovideo - cctv.com

7
1. P0WER
Please use the provided adaptor to connect power cord (Other adaptor is not suitable for this machine) .
2. EXTERNAL I/O
Controlled remotely by an external device or control system.
Alarm input, external I / O explanation.
3. 75 / HI
When using Loop function, please switch to HI. If you don t use Loop function or disconnect the video
input, please set it as 75 .
4. VIDEO INPUT (1 - 16)
Connect to video source, such as camera.
5. LOOP (1 - 16)
Connect video signal between Input port and Loop port to ma ke a loop.
6. AUDIO IN (1 - 4)
Connect to audio source, such as microphone.
IPS should be set to 25A (for NTSC) or 18A (for PAL)
4 audio inputs, but only can select 1 during recording.
7. AUDIO OUT (R/L)
Connect to monitor or speaker.
IPS should be set to 25A (for NTSC) or 18A (for PAL )
wi th 2 mono audio outputs from the same source.
8. MONITOR
Connect to Main monitor
9. CALL
Connect to CALL monitor. Show the Switch Display. When alarm tri gger happens, the call monitor will show
the triggered channel for a period of time.
BACK PANEL
LOOP
EXTERNAL I/O POWER
INPUT
WARNING : TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
IN
CALL
AUDIO
MONITOR
OUT
AUDIO
www.eurovideo - cctv.com

Connect the AC Power Cord with Power Adapter and plug into an el ectrical outlet. The Red LED indicator light will be
ON and the DVR is in Standby mode.
1.
Press the Power button. The POWER LED will turn from red to oran ge, and other red LED indicators will turn ON. It
takes approximately 5 to 15 seconds to boot the system with the message : HDD Detecting . Once connected, the
POWER LED will change to green color, and the Alarm LED will be ON.
2.
8
Before using the DVR, please have the HDDs installed ready. (refer to Appendix #1 for installation or remo val of HDDs ).
START THIS UNIT
Basic Operation
OPERATION
3. Before operating the DVR, please set up the system time first. ( for setting system time, please refer to page.11).
NOTE : When HDD not found message shows up, please refer to appendix # 1. As the HDD is l ikely not
installed correctly.
2002 JAN 01 01:02:03
M 032GB 080GB
RECORDING
TheDVRoffersavarietyof recordingmodes, suchasrecordcontinuously, at scheduledtime, andbyevents. Youcanset
up recording speed and resolution. You can set these options by selecting MENU / RECORD before recording, please refer
to page.14. Under the recording status, if power is off accidentally, recorded video will still store in the HDDs . DVR will
return to original recording situation after power returns again .
On the screen, you will find the date, time, HDD recording type, the amount of available GB left in the HDDs memory and
the letter M represents the method of recording that is occurring.
(OW : HDD Overwrite)
NOTE : 1. When the HDDs are full under O/W Recording mode, previous recorded
files may be overwritten without further warni ng notices.
2. XXGB at the left side means the left space in the Master HDD and at the right side means
the left space in the Slave HDD.
3. If the HDDs capacity is only 5 GB left, it will buzz for 3 seconds; so as i n 4GB, 3GB, 2GB and
1GB. If the O/W Recording mode(NOTE 1) is on, it won t have the warning buzzer.
There are 4 recording modes in which Recording can occur : Alarm , Timer and Manual Record.
1. ALARM RECORD
DVR is triggered by an alarm input. Indicated by the letter A and show diagram on the triggered channel.
2. TIMER RECORD
Recording is scheduled by a Timer. Indicated by the letter T.
3. MANUAL RECORD
Recording is initiated by manually pressing the REC button. Indicated by the letter M.
4. MOTION TRIGGER RECORD
Recording is triggered by motion detection. Indicated by the let ter D and show diagram on the triggered channel.
www.eurovideo - cctv.com

PLAY
Press PLAY button, the DVR will show the last recording.
1. FAST FORWARD (F.F. ) & FAST REWIND (F.R.)
You can increase the speeds of Fast Forward and Rewind on t he DVR.
In the Play mode, p ress once to get 2X speed forward and press twice to get 4X speed, and the maximum
speed can reach 32X.
Press once to get 1X speed rewind and press twice to get 2X speed, and the maximum speed can reach
32X.
2. SLOW FORWARD (S.F.) & SLOW REWIND (S.R.)
You can also slow down the speeds of Forward and Rewind on the DVR.
In the Play mode, p ress the SLOW button and you will enter Slow mode.
Press once to get 1/2X speed forward and press twice to get 1/4X spee d, and the slowest speed can reach
1/32X.
Press once to get 1/2X speed rewind and press twice to get 1/4X speed , and the slowest speed can reach
1/32X.
3. PAUSE
It will let you pause the current image displayed on the sc reen.
4. STOP
Press STOP under any circumstance, it will return DVR to live monitoring m ode.
5. IMAGE JOG DIAL
It will allow you to manually view video frame - by - frame, one image at a time.
While in PLAY mode, press PAUSE , it will pause the screen.
Press button to advance the frozen screen one image forward.
Press button to move back one image.
CAMERA SELECT (1 -- 16)
Press Camera Select (1 - 16) to select appointed camera to display on full screen mode.
9
www.eurovideo - cctv.com

The Menu allows you to configure your DVR settings. Please follo w below
steps to access the Menu :
Press the Menu button. The password screen will appear:
Password: 0000
The default Password is 0000. Simply press the Enter button to a ccess the Menu.
To key - in the Password, press the Right and Left buttons to move between numbers, and use the Up
and Down buttons to input the number.
Press the ENTER button once the correct Password is entered. The MENU options screen will appear.
Note: If you get a message Password Error , you have entered an incorrect password.
There are 6 options available in the Main Menu:
SEARCH -------- Find recorded list
TIMER ---------- Scheduling Record
RECORD ------- Record Mode Setup
CAMERA ------- Camera Channel Setup
SYSTEM -------- System Setup
EVENT ---------- Event List
10
Outlined below are the buttons used for Menu setting :
Up and Down : Scroll up and down or change values when an option is selected and is blinking
Left and Right : Scroll sideways within a menu option that has been selected
ENTER : Selects a submenu / an option under a submenu for browsing / mo dification
MENU : Completes modification of a menu option; exits a menu
ACCESS MENU
MAIN MENU
Detailed Menu Setup
NOTE :
(MENU)
SEARCH
TIMER
RECORD
CAMERA
SYSTEM
EVENT
www.eurovideo - cctv.com

MENU OPTIONS
SYSTEM
11
1. AUDIO INPUT
To choose one of 4 channels to record. ( only can select 1 during operation for recording )
2. INT AUDIBLE ALARM
To set the INTERNAL AUDIBLE ALARM. It will be trigged by ev ent occurrence when
the setting is ON.
5. ALARM DURATION
Set the reaction time which was determined by how long the
alarm mode responded to a buzzer. Default setting is 10 sec .
Options are 10 SEC, 15 SEC, 20 SEC, 30 SEC, 1MIN, 2MIN,
3 MIN, 5 MIN, 10 MIN, 15 MIN, 30 MIN, ALWAYS.
6. DWELL TIME
DWELL TIME is the time period that each channel sequentiall y
shown on call monitor.
7. MESSAGE LATCH
To select whether the DVR messages will disappear after 10
sec or remain on screen. NO is the default setting which th e
messages will go away after 10 sec.
NOTE : Video loss, Alarm and Motion messages will be shown
the same as Alarm Duration time.
8. TITLE DISPLAY
To set the title shown on monitor or not.
9. TIME DISPLAY
To set the time format on the DVR.
10. TIME
To set the correct time on the DVR.
3. EXT AUDIBLE ALARM
To set the EXTERNAL AUDIBLE ALARM. It will be trigged by ev ent occurrence when
the setting is ON.
(MENU)
SEARCH
TIMER
RECORD
CAMERA
SYSTEM
EVENT
4. MOTION AUDIBLE ALARM
To set the MOTION AUDIBLE ALARM. It will be trigged by
motion detection occurrence when the setting is ON.
( SYSTEM)
AUDIO INPUT : 1
INT AUDIBLE ALARM : ON
EXT AUDIBLE ALARM : ON
MOTION AUDIBLE ALARM : ON
ALARM DURATION : 10 SEC
DWELL TIME : 02 SEC
MESSAGE LATCH : NO
TITLE DISPLAY :ON
TIME DISPLAY : Y/M/D
2003 - JAN - 02(THU) 17:37:09
NEW PASSWORD : XXXX
CLEAR HDD : MASTER
SYSTEM RESET : NO
REMOTE MODE : RS - 232
BAUD RATE : 9600
REMOTE ID : 000
www.eurovideo - cctv.com

11. NEW PASSWORD : XXXX (Default password : 0000)
To set the new password.
12. CLEAR HDD
Delete all the contents of your HDD. When you choose YES on this option, you will be prompted with the
question shown : Press to clear HDD or press to confirm not to clear HDD.
13. SYSTEM RESET
Reset all system settings to book to factory default sett ings.
14. REMOTE MODE
Set the remote mode for connection with computer via RS - 232 or RS - 485. (Please refer to page.18 for RS - 232
Remote Protocol)
15. BAUD RATE
Set the remote protocol transmitting baud rate. Available Baud Rate are 115200, 57600, 19200, 9600, 4800,
3600, 2400 and 1200.
16. REMOTE PROTOCOL ID SETUP
To control different DVR by setting RS232 remote protocol . ID number can be set from 000 to 255.
12
ALL DATA IN HDD
WILL BE CLEARED
ARE YOU SURE?
( : NO : YES )
SEARCH
Press ENTER to confirm SEARCH setup, and the screen will show following opt ions.
(MENU)
SEARCH
TIMER
RECORD
CAMERA
SYSTEM
EVENT
1. LAST RECORD
Play the last recorded piece of video.
2. FULL LIST
Show a listing of all recorded video on the HDD which sorted by time.
D : Motion Record
M : Manual Record time
A : Alarm Record time
T : Timer Record time
M- HDD : Storage in Master HDD
S- HDD : Storage in Slave HDD
3. ALARM LIST
Show a listing of all recorded video triggered by an Alarm.
NOTE : If there are no Alarm in the record, the screen will
display EMPTY .
4. MOTION LIST
Show a listing of all motion detection triggered.
5. TIME SEARCH
Find video recorded on a specific date that is entered.
M 2002 - JAN - 01 01:02:03 M - HDD
M 2002 - JAN - 01 01:02:03 M - HDD
A 2002 - JAN - 01 01:02:03 M - HDD
T 2002 - JAN - 01 01:02:03 M - HDD
D 2002 - JAN - 01 01:02:03 S - HDD
M 2002 - JAN - 01 01:02:03 S - HDD
: PAGE UP : PAGE DOWN
LAST RECORD
FULL LIST
ALARM LIST
MOTION LIST
TIME SEARCH
www.eurovideo - cctv.com

13
TIMER
1. DAY
Select the day, or days of the week (Mon Fri / Sat - Sun / Daily) that you wish to schedule
the DVR to automatically record.
NOTE : 1.Special Date could be changed by Enter , Up and Down buttons.
2. If you have selected the specific date and recording timer set f rom that specific day to a new day,
then the Recording Timer Schedule will be set as whole week. For specific date of Recording Timer
Schedule, it is not recommended to set End Ti me over 23:59. For Example:If you set Timer Schedule
Day as Sunday, and START from 11:30, but End on 00:20, then Recording Timer Schedule is set as
from every Sunday's 11:30 to next Sunday's 00 :20. If you only want to set Recording Timer Schedule
from every Sunday 11:30 to Monday 00:20, then you should set Recording Timer Schedule as Sunday
from 11:30 to 23:59, and Monday from 00:00 to 00:20.
2. START
Select the starting time for the recording.
3. END
Select the finishing time for the recording.
4. QUALITY
Select the image quality for the recording. There are four Quality settings :
BEST, HIGH, NORMAL and BASIC.
5. IPS
Stand for Images Per Second and it could let you see Record submenu
for more details.
NTSC 25A 15 8421
PAL 18A 12 6321
NOTE : A means Record with Audio .
6. TIMER ENABLE
Enables / disables Timer recording function
(MENU)
SEARCH
TIMER
RECORD
CAMERA
SYSTEM
EVENT
( TIMER)
DAY START END QUALITY IPS
DAILY 00:00 00:00 BEST 25A
DAILY 00:00 00:00 BEST 25A
DAILY 00:00 00:00 BEST 25A
DAILY 00:00 00:00 BEST 25A
DAILY 00:00 00:00 BEST 25A
DAILY 00:00 00:00 BEST 25A
DAILY 00:00 00:00 BEST 25A
DAILY 00:00 00:00 BEST 25A
TIMER ENABLE : NO
www.eurovideo - cctv.com

14
(MENU)
SEARCH
TIMER
RECORD
CAMERA
SYSTEM
EVENT
(MENU)
SEARCH
TIMER
RECORD
CAMERA
SYSTEM
EVENT
RECORD
1. HDD OVERWRITE
Select YES to overwrite previous recording video in HDD.
NOTE : When the HDD is full under O/W Recording mode, previ ous recorded files
may be overwritten without further warning not ices.
2. RECORD IPS
Select the images per second of recording. The options are
as following :
NTSC 25A 15 8421
PAL 18A 12 6321
NOTE : A means Record with Audio .
3. RECORD QUALITY
There are four quality settings : BEST, HIGH, NORMAL and BA SIC.
NOTE : The relationship of Record time, IPS and record qual ity, please refer to page.25 Recording Speed.
4. ALARM REC IPS
Select the images per second of recording during an Alarm. The options are as following :
NTSC 25A 15 8421
PAL 18A 12 6321
NOTE : A means Record with Audio .
5. ALARM REC QUALITY
There are four quality settings during an Alarm : BEST, HIG H, NORMAL and BASIC.
NOTE : The relationship of Record time, IPS and record qual ity, please refer to page.25 Recording Speed.
6. MOTION TRIGGER RECORD
When you set up the MOTION DETECTION function (Please refer to P age.14 for MOTION DETECTION SETUP),
1. Select ON to set up the motion trigger record: It can automatically switc h from stand - by mode to Record Mode. The
motion detection will change the scanning sequence and shows and D on the monitor.
NOTE: The trigger recording time will depend on ALARM DURATION mode s etting (Please refer to page.11 for ALARM DURATION) and it will
record from the last trigger time. For example , when the alarm duration setting is 1 min, the time recording t ime is from 9:00:00 to 9:01:00.
If the motion detection trigged again at 9:0 0:40, the trigged recording time will from 9:00:00 to 9:00:40 an d 9:00:40 to 9:01:40. The total
recording time is 00:01:40.
2. Select OFF : The screen shows , the motion detection will change the s canning sequence while in record mode and shows
M on the monitor.
3. ( Brightness) / (Contrast) / (Color)
Have a video adjustment (Brightness / Contrast / Color) of each channel. The level is from 0 to 9.
4. ALARM
Select LOW / OFF / HIGH for alarm polarity. The default val ue is LOW.
5. RECORD
Set up which channel you want to record during alarm trigge r. The DVR record methods are as below :
EVENT : when alarm input is triggered, DVR will record alarming chan nel more frequently.
For example : when CH01 is triggered, the r ecord method will become 1 -2-1-3-1-4 .
NORMAL : when alarm input is triggered, DVR will record normally as se t up.
OFF : when alarm input is triggered, DVR will not record.
( RECORD)
HDD OVERWRITE: NO
RECORD IPS: 25A
RECORD QUALITY : NORMAL
ALARM REC IPS: 25A
ALARM REC QUALITY : HIGH
MOTION TRIGGER RECORD: ON
CAMERA
1. TITLE
Assign a title to each camera input. Initially each title i s the camera s number.
2. DWELL
Select ON to set up the channel auto switching on the call monitor.
www.eurovideo - cctv.com

15
MOTION DETECTION
MOTION DETECTION SETUP
1. Press MENU to enter the menu set up, then Down to CAMERA setup.
2. Press ENTER twice to enter the Motion Detection Setup.
3. Each screen displays the current camera picture overlaid with the motion targets (as Figure 1).
You can push the button Left or Right , Up or Down to adjust motion detection in ON or OFF.
4. The targets on each motion setup can be turned to ON or OFF i ndividually. To set up targets, using the
front panel buttons:
Press ENTER to confirm the channel
Press ENTER to enter motion mode
Up -- moves the target cursor up one row at a time.
Down -- moves the target cursor down one row at a time.
Left -- moves the target cursor left one column at a time.
Right -- moves the target cursor right one column at a time.
Press ENTER to turn the target cursor ON and press ENTER again to turn the target cursor OFF. (Figure 1 - 1)
Zoom turns all targets in the current row ON or OFF. (Figure 1 - 2)
PIP turns all targets on the screen ON or OFF. (Figure 1 - 3)
5. Press SLOW button to setup the Sensitivity list up to 255 and REC button to setup the Sensitivity list down to 000.
The default value is set on 32.
NOTE : Sensitivity value is related to motion and brightness cha nge. Low value (as 001) means higher sensitivity
on motion and brightness change. High value (as 255 ) means lower sensitivity on motion and brightness
change. User can choose the suitable sensitivity va lue in different locations.
NOTE : When motion trigger record setting is ON, it can automatically s witch from stand - by mode to record mode.The motion
detection will change the scanning sequence and sho ws on the monitor. There will be an action as following:
For example : If the motion is detected on Camera #1, its record ing & scanning sequence will be more frequently. The
sequence will be as 1st, 2nd, 1st, 3rd, 1st, 16th. And channel 1 will show on the screen. If 2nd camera and 3rd camera
both motion detection are activated, they will be scanning as 1s t, 2nd, 3rd, 2nd, 2nd, 3rd, 3rd, 2nd, 3rd, 4th, 2nd, 3rd and
vice versa. And CH2 & CH3 will show for a period of time wh ich is same as Alarm Duration time.
www.eurovideo - cctv.com

16
Figure 1 MOTION DETECTION SETUP
12 3 4 5 6 7 8 9
10 11 12 13 14 15
--
-- -- -- -- -- -- -- -- -- -- -- -- -- --
032
12 3 4 5 6 7 8 9
10 11 12 13 14 15
--
-- -- -- -- -- -- -- -- -- -- -- -- -- --
Figure 1 - 1 MOTION DETECTION SETUP 1~15
032
12 3 4 5 6 7 8 9
10 11 12 13 14 15
--
-- -- -- -- -- -- -- -- -- -- -- -- -- --
Figure 1 - 2 MOTION DETECTION SETUP -- LINE
032
Figure 1 - 3 MOTION DETECTION SETUP -- ALL
12 3 4 5 6 7 8 9
10 11 12 13 14 15
--
-- -- -- -- -- -- -- -- -- -- -- -- -- --
032
EVENT
There are only 16 recorded events will be shown on a single page and please press or to change the
pages or press + to CLEAR the EVENT record.
(MENU)
SEARCH
TIMER
RECORD
CAMERA
SYSTEM
EVENT
M HDD WARNING 2002 - JAN - 01 03:00:00
M HDD LOSS 2002 - JAN - 01 03:00:00
M HDD ERROR 2002 - JAN - 01 03:00:00
S HDD WARNING 2002 - JAN - 01 03:00:00
HDD FULL 2002 - JAN - 01 03:00:00
SYSTEM ERROR 2002 - JAN - 01 03:00:00
---- 02 VLOSS 2002 - JAN - 01 03:00:00
---- 03 ALARM 2002 - JAN - 01 03:00:00
: PAGE UP : PAGE DOWN + : CLEAR
M- HDD WARNING: Master HDD might be failed.
M- HDD LOSS: Master HDD does not exist. Now user can use the other HDD.
M- HDD ERROR: Master HDD might be error
S- HDD WARNING: Slave HDD might be failed
S- HDD LOSS: Slave HDD does not exist. Now user can use the other HDD.
S- HDD ERROR: Slave HDD might be error
HDD FULL: HDD is full
SYSTEM ERROR: System might be failed
---- 02 VLOSS: Channel: 2 Video loss
---- 03 ALARM: Channel: 3 External I/O Alarm have triggered
POWER RESTORE : Power restore
www.eurovideo - cctv.com

SELECT
This device allows user to get the ideal view size.
Press , , button to make different vie w size.
Press Select then Left or Right button to locate the desired position.
Press Camera Select (1 - 16) to select the appointed camera.
Press Menu to exit.
PICTURE IN PICTURE (PIP)
Press PIP button to enter PIP display screen. The PIP fo rmat displays a full screen background picture
with a 1 / 16 size screen insert .
Press button to move the insert screen.
Press Select button to confirm the camera selection.
Press Left or Right to choose background or insert screen.
Press camera select (1 - 16) to select appointed camera into screen.
Press Menu to exit.
ZOOM
Press ZOOM button to enlarge the display of main picture. It dis plays zoomed picture on main picture and a
small window inserted. The inserted window contains a movable 1/ 4 view size of the appointed camera.
Press the appointed Camera Select (1 - 16) .
Press Zoom button to select zoom mode.
Press the Zoom button again to move the zoom pointer.
Press Menu to exit.
VIDEO LOSS
Screen will display if the video input is not connected properly.
17
OPERATION OPTIONS
Advanced Operation
www.eurovideo - cctv.com

RS232 REMOTE PROTOCOL
18
KEY LOCK
For further security, you can Lock all buttons on your DVR. Locking disables the buttons and preve nts other people from
using the system.
Press ENTER and MENU at the same time to enable Key Lock.
Press ENTER and MENU at the same time and key in password (Defau lt : 0000), then press ENTER to disable Key Lock.
You can use the PC keyboard to simulate DVR keypad.
DATA: REMOTE PROTOCOL using 8 bit data 1 start bit 1stop bit
FUNCT ION CODE ASCII FUNCTION CODE ASCII
KEY_MENU 0x4D M KEY_CH1 0x31 1
KEY_SELECT 0x73 s KEY_CH2 0x32 2
KEY_ENTER 0x0D ENTER KEY_CH3 0x33 3
KEY_4CUT 0x61 a KEY_CH4 0x34 4
KEY_ZOOM 0x5A Z KEY_CH5 0x35 5
KEY_9CUT 0x62 b KEY_CH6 0x36 6
KEY_PIP 0x70 p KEY_CH7 0x37 7
KEY_16CUT 0x63 c KEY_CH8 0x38 8
KEY_SLOW 0x53 S KEY_CH9 0x39 9
KEY_REC 0x72 r KEY_CH10 0x41 A
KEY_LEFT 0x4C L KEY_CH11 0x42 B
KEY_UP 0x55 U KEY_CH12 0x43 C
KEY_PLAY 0x50 P KEY_CH13 0x44 D
KEY_DOWN 0x4E N KEY_CH14 0x45 E
KEY_RIGHT 0x52 R KEY_CH15 0x46 F
KEY_POWER 0x57 W KEY_CH16 0x47 G
KEY_KEY_LOCK 0x4B K
www.eurovideo - cctv.com

TROUBLE SHOOTING
19
When malfunction occurs with DVR, it may be not serious and can be corrected easily. The table below describes some
typical problems and their solutions. Please check them before c alling your DVR dealer.
PROBLEM SOLUTION
Please Insert HDD
Please use the Key to lock the HDD Cartridge
And press any key
Check power cord connections.
Confirm that there is power at the outlet.
Check if it is under Key Lock mode.
Press "
MENU"
& "
ENTER"
to exist Key Lock mode.
No recorded video Check if the HDD is installed properly.
Timer Record enable
does not working
Check if the Record Enable is set to YES
Check camera video cable and connections.
Check monitor video cable and connections.
Confirm that the camera has power.
Check camera lens setting.
No live video
HDD Not Found
No power
Not working when
press any button
SPECIFICATIONS
Video format NTSC/EIA or PAL/CCIR
Hard disk storage IDE type, UDMA 66, supported over 200GB HDD
Record mode Manual / Alarm / Timer / Motion
Camera Input Signal Composite video signal 1 Vp-p 75
BNC, 16 channels
Camera Loop Back Composite video signal 1 Vp-p 75
BNC, 16 channels
Main Monitor Output Composite video signal 1 Vp-p 75
BNC
Call Monitor Output Composite video signal 1 Vp-p 75
BNC
Audio input 4 audio inputs, (RCA) *
Audio output 2 audio outputs, (RCA) **
Motion Detect Area 15 * 12 targets per camera (NTSC) / 15 * 14 targets per camera (PAL)
Motion Detect Sensitivity 256 Levels
Video Loss Detection
Yes
Refresh Rate Up to 72 images/sec. for NTSC / 60 images/sec. for PAL
Recording Rate Up to 25 images/sec. for NTSC / 18 images/sec. for PAL
Dwell Time
Programmable (1~10 Sec)
Picture in Picture
Yes (Movable)
Key Lock
Yes
Picture Zoom
2*2 (Movable)
Camera Title
6 letters
Video Adjustable Color/ Contrast/ Brightness Adjustable
Alarm Input TTL input, Hi (5V), Low (GND)
Alarm Output COM,/N.O
Remote Control RS-232 or RS-485
Time Display Format YY/MM/DD, DD/MM/YY, MM/DD/YY, OFF
Power Source
AC100~240V + 10% switching adaptor
Power Consumption
<45W
Operation Temperature 10 ~ 40
RS-232C / RS-485 (bps)
115200 57600 19200 9600 4800 3600 2400 1200
Dimension (mm) 432(W) x 110(H) x 325(D)
Net Weight 5.7 kgs
Specifications are subject to change without notice.
4 audio inputs, but only can select 1 during operation for reco rding
wi th 2 mono audio outputs from the same source.
www.eurovideo - cctv.com