Eurotherm 7000 Series User manual

Single phase
solid state
contactors
User Manual
7
100S
7100S
ENG
• DATA MANAGEMENT • CONTROLS • PROCESS AUTOMATION•

i
7100S
SMART CONTROLLERS
SINGLE-PHASE INDUSTRIAL SOLID STATE
CONTACTORS
7000 series
User
Manual
© Copyright Eurotherm Limited 2003
All rights reserved. All reproduction or transmission in any form whatsoever and using any procedure
(electronic or mechanical, including photocopying and recording) without written permission from
Eurotherm is strictly prohibited.
Ref.: HA176386ENG - Issue 2.0 - 09/2003

7100S User Manual
ii

7100S User Manual iii
Contents
CONTENTS
Page
European directives and applicable standards . . . . . . . . . . .iv
Commissioning flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . .vi
Chapter 1 Solid state contactor identification . . . . . . . . .1-1
Chapter 2 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-1
Chapter 3 Operation (Firing, Alarms) . . . . . . . . . . . . . . .3-1
Chapter 4 Commissioning and Maintenance . . . . . . . . .4-1
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5.1
Eurotherm business group addresses . . . . . . . . . . . . . . . . .6-1
PURPOSE OF MANUAL
This manual (Issue 2.0) describes the Basic Version and all options for 7100S series
solid state contactors with current ratings of up to 250 A.
General information about the digital communication option is presented in the
technical specifications (section 1).
The operation of 7100S units with this option and the operation of the digital
communication are described in the ‘7000 Series. Digital Communication’ manual
(part number HA176664ENG available later).

7100S User Manual
iv
Applicable standards
EUROPEAN DIRECTIVES AND APPLICABLE STANDARDS
COMPLIANCE WITH PRODUCT STANDARD
7100S products comply with the terms of product standard EN 60947-4-3
‘Contactors and motor-starters - AC semiconductor controllers and contactors for non-
motor loads’. The number of this standard is indicated on the front panel label.
CE LABELLING
7100S products, installed and used in accordance with their user manual, bear CE labelling
to indicate compliance with the essential requirements of:
• the European Low Voltage Directive 73/23 EEC dated 19 February 1973
amended by 93/68 EEC dated 22 July 1993
• the Electromagnetic Compatibility Directive 89/336/EEC dated 3 March 1969
amended by 92/31/EEC dated 28 April 1992 and 93/68/EEC dated 22 July 1993.
SAFETY
The units have IP20 protection rating as defined by standard IEC 60529.
External wiring must comply with standards IEC 60364-4-43 and IEC 60943.
Copper cables and conductors rated to a temperature of 75°C (167°F) must be used.
ELECTROMAGNETIC COMPATIBILITY EMC) TEST STANDARDS
7100S products installed and used in accordance with the user manual, are designed for an
industrial environment and must not be used in the home.
IMMUNITY
The EMC immunity test standards required by product standard EN 60947-4-3 are given in
table 1.
Table 1 EMC immunity standards compliance
Test type Minimum levels EMC test standard
Electrostatic discharge 4 kV on contact; 8 kV in air EN 61000-4-2
Radiated, radio frequency 10 V/m 80 MHz ≤f≤1 GHz;
electromagnetic field 80% modulation 1 kHz sinusoidal EN 61000-4-3
Electrical fast transient / burst 2 kV / 5 kHz EN 61000-4-4
Electrical surge 4 kV line to earth;
2 kV line to line EN 61000-4-5
Conducted disturbances 140 dBµV; 150 kHz ≤f≤80 MHz EN 61000-4-6
Voltage dips, short interruptions
and voltage variation 5 s interruptions EN 61000-4-11

7100S User Manual v
Applicable standards
EMC FILTER conducted emissions)
For facilities required to comply with the levels stipulated under the generic standard for
conducted emissions, EN 61000-6-4, Eurotherm Automation can provide optional internal
filters (code FILT) on units up to 100 A.
EMC GUIDE
To help you deal with installation-dependent electromagnetic interference effects,
Eurotherm provides an ‘Electromagnetic compatibility’ installation guide
(ref. HA025464) which sets out best current practice regarding EMC.
DECLARATION OF CONFORMITY
A CE declaration of conformity is available on request.
EMISSIONS
The EMC emissions test standards required by product standard EN 60947-4-3 are given in
table 2.
Table 2 EMC emissions standards compliance
Emission type Firing mode EMC test standard
Radiated, radio frequency All firing CISPR 11 Class A
modes
Conducted, radio frequency ‘Burst mode’ and ‘Single-cycle’ CISPR 11 Class A
Group 2
‘Phase angle’
(Product compliant if external
series filter fitted)

7100S User Manual
vi
Quick commissioning
Alarmes signalées Alarmes signalées
Check characteristics of unit
and installation
Power wiring
Power up
Check supply presence
et DLF alarm: option
(if conditions met)
Normal operation
Product code
and specifications
correspond
Pages 1-7
to 1-13
upply protection,
protective earth (PE terminal)
Alarms signalled
Pages 4-2, 4-3
GRF, DLF, T°LEDs Pages 3-5 to 3-7
ON and HEAT LEDs
Apply input signal
Check firing
Page 2-12
CHK/SET push button Pages 3-9, 3-10,
4-3
Power terminals
upply: 1/L1, 3/L2 (1/L1 for ≥ 250A)
Load: 2/T1, 4/T2 (2/T1 for ≤ 250A)
Pages 2-7 to 2-9,
4-3
Input signal wiring Page 2-10
DC logic signal:
LDC terminal block
AC logic signal:
HAC terminal block
4-20 mA analogue signal:
ATP terminal block
Digital signal (MOP option) :
COM terminal block
Auxiliary supply Pages 2-9, 4-3
Fan:
FAN terminal block (rating ≥ 250 A )
24 Vdc or 24 Vac
(for RTR or MOP option) :
Aux2 terminal block
Green ON LED
Green HEAT LED and
load current present
Maintenance
Pages 2-10, 3-4
Pages 2-8, 2-9,
4-3
COMMISSIONING FLOWCHART

7100S User Manual 1-1
Identification
Chapter 1
SOLID STATE CONTACTOR IDENTIFICATION
Contents Page
General presentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2
Basic version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2
Versions with options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-3
Technical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-7
Coding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-12
Example code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-14
Identification label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-14

Identification
7100S User Manual
1-2
Chapter 1 IDENTIFICATION
GENERAL PRESENTATION
7100S series solid state contactors are used to control the electrical power of single phase
industrial loads. The load controlled may comprise low temperature coefficient resistive
loads or short wave infrared (SWIR) elements.
Current ratings vary from 16 A to 630 A (see coding), at voltages of 100 V to 690 V.
7100S series power thyristor units (rating of up to 100 A) comprise two channels, one
controlled by thyristors and one direct internal channel.
7100S units rated 125 A and above only comprise a single controlled channel.
Figure 1-1 General view of 7100S, Basic version (here with DC logic input, 16 rating)
EUROTHERM
7100
S
16 A / 230 V
ε
2/T2
1/L1
HEAT
ON
PE
3/L2
4/T2
Internal wiring
diagram
Supply present
Protective earth
terminal
Input logic signal
terminal block
Thyristor firing
request (logic)
Power terminals
(supply side)
Power terminals
(load side)
Input logic signal
terminal labelling
Nominal current (rating)
and nominal voltage
User
label
EN 60947-4-3
LDC
0VL LD
11 12
Product standard
BASIC VERSION (without options

Figure 1-2 General view of 7100S with DLF option (here with 100 A rating and DC logic input)
7100S User Manual 1-3
Identification
EUROTHERM
ε
7100
S
100 A / 500 V
PE
3/L2
4/T2
GRF
DLF
ON
HEAT
CHK
SET
Internal
wiring diagram
Protective earth
terminal
Input logic signal
terminal block
Power terminals
(supply side)
Input logic
signal labelling
GRF or DLF option:
larm relay contact
terminal block
Supply present
Firing request
(logic)
Serious alarms
Partial load
failure alarm DLF option
CHK/SET
push button:
DLF alarm
setting / diagnosis
Alarms option:
larm relay
contact terminal
labelling
Rating (nominal current)
and nominal voltage
Power terminals
(load side)
User label
larm
options
EN 60947-4-3
1/L1
2/T1
Product standard
ALR
1a 1b
73 74
LDC
0VL LD
1112
VERSIONS WITH OPTIONS
The figures below show general views of 7100S units (100 and 250 A versions) with Alarms,
Retransmission or Communication options and with various input types.
The diagrams indicate the power and command terminals, terminal block labels, indicators
and settings push button.
Options (alarms
Figure 1-2 shows a general view of the 7100S with GRF (serious alarms) and DLF
(Diagnostic Load Failure alarm) options.

Identification
7100S User Manual
1-4
Figure 1-3 General view of 7100S, 250 rating (here with DLF, DC logic input, 230V fan power supply)
1/L1
2/T1
EUROTHERM
ε
7100
S
250 A / 500 V
PE
GRF
DLF
ON
HEAT
CHK
SET
EN 60947-4-3
1/L1
2/T1
LDC
0VL LD
11 12
ALR
1a 1b
73 74
T°
FAN
230 N
16 17 18
EXT
L2
21 22
MSF
3a 3b
75 76
Internal wiring diagram
(internal fuse for
125 to 250 ratings)
Control
terminal block
Controlled phase terminal
(supply side)
Control terminal
labelling
Signalling LEDs
(alarms and operation)
Internal fuse
compartment
Protective earth
terminal
Not
used
DLF option:
CHK/SET
push button:
DLF alarm
setting / diagnosis
Fuse blown
contact
(code MSFU)
Controlled phase
terminal
(load side)
Not
used Fan
Fan power supply
(250 only)
Over-temperature alarm
(250 only)
2 attachment screws
for internal fuse
compartment
Figure 1-3 shows a general view of a fan-cooled 7100S unit with alarms.

7100S User Manual 1-5
Identification
Figure 1-4 General view of 7100S with Retransmission option (here with 100 A rating, analogue input)
EUROTHERM
ε
7100
S
100 A / 500 V
GRF
DLF
ON
HEAT
CHK
SET
PE
3/L2
4/T2
2/T1
1/L1
EN 60947-4-3
Aux2
24V0VS
1920
RTR
0V1DC1
4142
ALR
1a 1b
7374
ATP
0VARI
1112
Internal
wiring diagram
Protective earth
terminal
nalogue
input signal
terminal block
Power terminals
(supply side)
nalogue
input signal
terminal labelling
larm relay
contact
terminal block
Supply
present
Firing request
(burst mode)
Serious alarms
Partial load
failure
alarm
DLF option:
CHK/SET
push button:
DLF alarm
setting / diagnosis
Rating (nominal current)
and nominal voltage
Power terminals
(load side)
User labelling
Retransmission
power supply terminal
labelling
Version with Analogue Retransmission Option
The Retransmission option (only available with the DLF option) provides an analogue signal
which follows the rms load current.
Figure 1-4 shows a general view of a 7100S unit with DLF and Retransmission options (here
with analogue ATP input signal and Burst mode firing).

Identification
7100S User Manual
1-6
Figure 1-5 General view of 7100S with DLF and communication options (here with 100 A rating)
EUROTHERM
ε
7100
S
100 A / 500 V
GRF
DLF
ON
HEAT
CHK
SET
PE
3/L2
4/T2
2/T1
1/L1
EN 60947-4-3
COM
B A
9192
ALR
1a1b
7374
Protective earth
terminal
Power terminals
(supply side)
Power terminals
(load side)
Digital
communication
option:
Transmission LEDs
and configuration
microswitches
DLF option:
CHK/SET
push button
Internal
wiring diagram
larm relay
contact
terminal block
Supply
present
Firing request
(burst mode)
Serious alarms
Partial load
failure
alarm
Communication
option:
Supply and ground
terminal labelling
RS485 digital bus
terminal block
Digital
Communication bus
terminal labelling
Communication option:
Supply and ground
terminals
ON/
Dxch
Rx
Tx
ON
1 2 3 4 5 6 7 8
Aux2
GND24V0VS
151920
Version with digital communication option
Digital communication (RS485 bus) provides 7100S solid state contactors with digital control
and retransmission of various values and operating parameters (the DLF option is required
to transmit the load current).
The operation of the digital communication option is described in the manual ’7000 Series.
Digital Communication’ (part number HA176664ENG available later).
Figure 1-5 shows the general view of a 7100S unit with the digital communication option.

7100S User Manual 1-7
Identification
TECHNICAL SPECIFICATIONS
USE In accordance with product standard EN 60947-4-3:
Devices for continuous duty:
1. Semiconductor contactor variant 5:
Logic input signal:
• DC (LDC input) or
• AC (HAC input).
2. Thyristor unit variant 4:
4-20 mA analogue input signal (ATP input)
or digital communication option.
Configuration as product code.
POWER
Nominal current 16 A to 250 A (at 45°C) depending on product code
(see coding).
Nominal voltage 100 V to 500 V (+10% and -15%) available depending on
product code.
Frequency Use from 47 to 63 Hz (automatic matching)
Dissipated power typical 1.3 W per amp (2 W max., fuses included)
Cooling Natural convection (ratings up to 200 A) or
Fan (ratings over 250 A); consumption 10 VA
(115 V or 230 V external power supply).
LOAD
Categories of use The categories of use applicable for each unit are indicated
on the identification label.
• AC-51 Non-inductive or low inductance loads, furnace
resistances (resistive load with low temperature
coefficient).
•
AC-55b Switching of incandescent lamps, short wave
infrared elements (SWIR).
FIRING MODES
Thyristor switching At thyristor voltage zero crossing.
‘Logic’ mode DC signal applied to LDC input
AC signal applied to HAC input
‘Burst’ mode Supply voltage modulated by analogue signal applied to
ATP input
(Analogue to Time Proportional).
Firing base time: approx. 15 cycles
With ‘Digital Communication’ option
(available later) firing base time:
• 1 half-cycle (‘Advanced single-cycle’ mode)
• 1 cycle (‘Single-cycle’ mode)
• 16 or 64 cycles (‘Burst mode’).

Identification
7100S User Manual
1-8
CONTROL
Power supply Self-powered electronics.
‘Logic’ firing:
•DC signal Conducting from 4.5 Vdc to 32 Vdc max, current ≥9 mA.
(LDC input) Off < 1.5 V or < 0.1 mA.
Typical response time ≤10 ms.
• AC signal
Conducting from 85 to 253 Vac max. Impedance ≈7 kΩat 50 Hz.
(HAC input) Off < 10 Vac.
Typical response time ≤60 ms.
If an RC snubber contact protection circuit or control
optotriac is used, the maximum capacitor value is 22 nF
for 240 Vac
‘Burst mode’ firing:
• Analogue signal 4 - 20 mA (10 Vdc max).
(ATP input) Modulation depending on analogue signal.
Firing base time: 0.3 s.
• Digital signals Digital communication option
(COM input) (available later);
Modbus® protocol.
CONTROL
Control type ATP input only:
Open loop, no compensation of supply voltage variations.
Digital communication option:
Supply voltage compensation operates for variations of
up to ±20% of nominal voltage, using V2control
Linearity and Stability
Better than ±2% of full scale on sinusoidal supply.
SIGNALLING
All versions
Supply present Green ‘ON’ LED.
Thyristor firing request Green ‘HEAT’ LED.
Alarm option Red LED (serious alarms) GRF and / or
Orange LED (DLF alarm).
Alarm relay contact.
Communication option
Front panel LEDs Green LED (power supply and exchange status) and
two Orange LEDs (Receive and Transmit data).
Communication bus Read and write operating parameters
(load current available with DLF option).
Retransmission of all types of alarm.

7100S User Manual 1-9
Identification
ALARMS (Options
GRF option
Serious alarms Total load failure (TLF) and thyristor short circuit (THSC)
detection.
Signalling When a serious alarm is detected:
• the red ‘GRF’ LED is lit
• the alarm relay contact is activated.
DLF option
Diagnostic alarm Partial load failure detection and diagnosis.
Important: For SWIR
elements the DLF option applies:
• if the elements are powered at nominal voltage and
• in ‘Single-cycle’ mode only (available with digital
communication option or with Eurotherm REMIO/TPO or
i7000 synchronised interfaces).
Signalling
If a partial load failure (PLF fault) is detected:
• the orange ‘DLF’ LED is lit
• the alarm relay contact is activated.
Settings The front panel push button is used for:
• monitoring and diagnosis
• adjusting and resetting the alarm.
Sensitivity Detects the failure of at least one heating element for six
identical elements connected in parallel
(one element in four for SWIR elements).
Extension The DLF option includes Serious alarm monitoring
(GRF option included).
Over-temperature alarm
Operation For all fan-cooled units (≥250 A), the unit stops firing if the
temperature threshold is exceeded regardless of the options
fitted.
Signalling Red ‘T°’ LED and Alarm relay contact
(if one of the alarm options is selected).
Alarm relay Fitted if one of the alarm options is selected.
The relay contact (0.25 A/230 Vac or 30 Vdc) is either open on
alarm or closed on alarm depending on the product code.
RETRANSMISSION or COMMUNICATION (exclusive options
RETRANSMISSION
Availability Isolated analogue retransmission is available with the DLF
option but without the digital communication option.
Retransmitted value Analogue image of rms load current.
The rms current is calculated:
• over the modulation period (in burst mode with ATP input)
• over a fixed duration of 1.6 s (Logic mode, LDC or HAC input).
Output signal Selected on ordering:
• 4-20 mA current, Vmax = 12.5 V on 500 Ωresistor
• 0-10 V voltage, Imax = 24 mA on 500 Ωresistor.
Power supply 24 Vac (±20%), 47 to 63 Hz or 24 Vdc (±20%) non-polarised.
Typical consumption 1.5 VA
Protection: external 2 A fuse.

Identification
7100S User Manual
1-10
DIGITAL COMMUNICATION
Availability The digital communication option is exclusive with:
• the Retransmission option or
• control using the logic or analogue input signal.
Protocol Modbus® RTU.
Compliance Communication complies with the specifications given in
‘GOULD MODICON Protocol Reference Guide PI-MBUS-300 rev J’.
Power supply 24 Vac (±20%), 47 to 63 Hz or
24 Vdc (±20%) non-polarised.
Typical consumption 1.5 VA
Protection: external 2 A fuse.
External wiring should comply with standard IEC 60364.
Transmission Standard RS485, 2 wires.
Speed: 9600 or 19200 baud.
Selected by switch on front panel. The speed is factory set to
correspond to the selected product code.
Termination The communication bus must have termination resistors fitted
at each end:
• one line impedance matching resistor.
• two RS485 bus polarisation resistors.
Address Adjustable between 1 and 127 using front panel switches
only. The physical address is factory configured to 32 by default.
Diagnostic • Green LED on front panel indicates power presence, waiting
for frames, communication established.
• Two orange LEDs show the status of the communication bus
(transmission or reception).
Control Supply voltage compensation operates for variations up to ±20%
of nominal voltage, using V2 control
Parameters and
operating mode Read and write by digital communication
(see Digital communication manual, part No. HA176664ENG).
Firing base time
Configurable over communication link:
• 1 half-cycle (‘Advanced single-cycle’ mode)
• 1 cycle (‘Single-cycle’ mode)
• 16 or 64 cycles (‘Burst mode’).
The default base time is factory configured to 16 cycles.

7100S User Manual 1-11
Identification
PROTECTION
Co-ordination type
for short circuits Type 1 (quick-acting fuses).
Electrical protection IP20 without adding additional protection.
Thyristors Varistors and RC snubbers.
Quick-acting fuses
(except for Short wave infrared elements):
• rating ≤100 A: external
• rating ≥125 A: internal.
With MSFU code (selection corresponds to code):
• for external fuses, the fuse blown contact is wired directly
on the fuse;
• for internal fuses, the contact (open after fuse blows) is
accessible on the ‘MSF’ terminal block
Replacement fuses: see section 4.
ENVIRONMENT
Use 0 to 45°C at nominal current,
at maximum altitude of 1000 m.
Storage -10°C to +70°C.
Isolation voltage Assigned isolation voltage Vi= 500 Vrms
Pollution Degree 2 acceptable (defined by IEC 60664).
Humidity RH 5% to 95%, non-condensing, non-streaming.
Over-voltage Over-voltage category II (as defined by IEC 60664)
V
imp
= 4 kV.
Mounting
Mounting • rating ≤100 A:
attachment plate(s) fixed to unit:
- on symmetrical EN50022 DIN rail or
- bulkhead mounting.
• rating ≥125 A: bulkhead mounting only.
DIMENSIONS AND WEIGHT
Rating Height Width (mm Depth (mm Mass (kg
(A (mm Basic Options Basic Options Basic Options
16 156 35 52.5 110 135 0.42 0.56
25 156 35 52.5 140 165 0.56 0.7
40 156 52.5 52.5 140 165 0.8 0.9
63 156 70 70 160 185 1.3 1.45
80-100 226 96 96 164 189 1.7 1.85
125-200 424 144 144 285 285 5.1 5.6
250 424 144 144 285 285 5.6 6.0
Eurotherm’s policy of continuous product improvement and development means that the specifications in this document may
be modified without prior notice.

Identification
7100S User Manual
1-12
6. Input Code
Communication option (without
logic or analogue input) NONE
No communication.
Logic firing:
DC logic signal LDC
4.5 Vdc to 32 Vdc
AC logic signal
85 Vac to 253 Vac HAC
‘Burst mode’ firing:
Analogue DC signal
4 mA to 20 mA ATP
CODING
7100S Current / Voltage / Filter / Fan / Fuse / Input / Manual / Selected /
options
1. Nominal current Code
16 amps 16A
25 amps 25A
40 amps 40A
63 amps 63A
80 amps 80A
100 amps 100A
125 amps 125A
160 amps 160A
200 amps 200A
250 amps 250A
315 amps 315A*
400 amps 400A*
500 amps 500A*
630 amps 630A*
2. Nominal voltage Code
127 volts 127V
230 volts 230V
277 volts 277V
500 volts 500V
690 volts 690V*
4. Fan Code
16A to 200A:
no fan XXXX
≥250A: fan
• 115 V supply 115V
• 230 V supply 230V
3. Internal EMC filter Code
16A to 40A:
with filter only FILT
63A to 100A:
• with filter FILT
• no filter NONE
≥125A:
no filter only NONE
5. High speed fuse Code
Thyristor protection fuse
• without microswitch FUSE
• with microswitch MSFU
(≤100 A: external fuse
≥125 A: internal fuse)
No fuse or control of
short wave infrared elements NONE
7. Manual language Code
French FRA
English UK ENG
German GER*
English USA USA*
Spanish SPA*
Italian ITA*
8. Selected options Code
No options
End of code NONE
Selection of options YES
Ratings and Basic selection

9. Alarm option Code
Serious Alarms:
Thyristor short-circuit,
Total Load failure,
(over-temperature for ≥250 A) GRF
Partial load failure
and Serious alarms DLF
No alarms NONE
7100S User Manual 1-13
Identification
11. Alarm relay contact Code
GRF or DLF option:
Alarm relay contact
• Closed on alarm NC
• Open on alarm NO
Without alarm option XX
10. Load type Code
For DLF option:
• Resistive load with
low temperature coefficient LTCL
• Short wave infrared elements SWIR
Without DLF option XXXX
12. Communication or
retransmission option * Code
Digital communication
Modbus® protocol MOP
Analogue retransmission
(DLF option required) RTR
No communication
or retransmission NONE
13. Transmission speed * Code
or retransmitted signal
Code MOP.
Transmission speed:
9.6 kbaud 9K6
19.2 kbaud 19K2
Codes RTR and DLF.
Analogue rms current
retransmission output:
current 4-20 mA 4mA20
voltage 0-10V 0V10
Code NONE.
No communication
or retransmission XXXX
14. Certification option Code
Without certificate of
‘Compliance with Order’ NONE
With certificate of
‘Compliance with Order’ CFMC
* Available later
Alarm option Communication or Retransmission Option Certificate
Type / Load / Contact / Protocol or / Speed or retransmitted / option
Retransmission signal
Options (Options selected: YES)