evertz SRF Series User manual

SRF Series RF Splitters and Combiners
Revision 0.1
TABLE OF CONTENTS
1. OVERVIEW......................................................................................................................................... 1
1.1. BLOCK DIAGRAMS ....................................................................................................................... 2
1.2. TYPICAL APPLICATION DIAGRAM.................................................................................................. 3
2. INSTALLATION.................................................................................................................................. 3
3. SPECIFICATIONS.............................................................................................................................. 5
3.1. RF INPUT/OUTPUT................................................................................................................... 5
3.2. PHYSICAL................................................................................................................................. 5
Figures
Figure 1: Front View of SRF3-64-1x2 chassis .................................................................................................... 1
Figure 2: Rear View of SRF3-64-1x2 chassis ..................................................................................................... 1
Figure 3: 1x2 Splitter / 2x1 Combiner................................................................................................................. 2
Figure 4: 1x4 Splitter / 4x1 Combiner.................................................................................................................. 2
Figure 5: 128x128 L band matrix using XRF6 64x64 routers and SRF3-64-1x2 modules................................. 3
Figure 6: Front Panel of SRF3-64-1x2 chassis................................................................................................... 4
Figure 7: Rear Panel of SRF3-64-1x2 chassis ................................................................................................... 4

SRF Series Splitters and Combiners
Revision 0.1
REVISION HISTORY
REVISION DESCRIPTION DATE
0.0 Preliminary Version Jun 06
0.1 Updated to SRF specs Jul7 07
Information contained in this manual is believed to be accurate and reliable. However, Evertz assumes no responsibility for the use thereof nor for
the rights of third parties, which may be effected in any way by the use thereof. Any representations in this document concerning performance of
Evertz products are for informational use only and are not warranties of future performance, either express or implied. The only warranty offered by
Evertz in relation to this product is the Evertz standard limited warranty, stated in the sales contract or order confirmation form.
Although every attempt has been made to accurately describe the features, installation and operation of this product in this manual, no warranty is
granted nor liability assumed in relation to any errors or omissions unless specifically undertaken in the Evertz sales contract or order confirmation.
Information contained in this manual is periodically updated and changes will be incorporated into subsequent editions. If you encounter an error,
please notify Evertz Customer Service department. Evertz reserves the right, without notice or liability, to make changes in equipment design or
specifications.

SRF Series Splitters and Combiners
Revision 0.1 SRF-1
1. OVERVIEW
The SRF series radio frequency ( RF ) passive splitters and combiners provide an economical method of
splitting or combining a number of RF signals in ratios of 1:2 or 1:4. They provide low insertion loss, high
return loss, flat frequency response and high isolation between channels. They can be used for signal
distribution in a RF facility, or used to expand the matrix size of Evertz Microsystems XRF1 ( 16x16 ) and
XRF6 ( 64x64 ) RF routers.
Figure 1: Front View of SRF3-64-1x2 chassis
Figure 2: Rear View of SRF3-64-1x2 chassis
The SRF products feature RF coax connectors on both sides of the chassis for mounting on either the
front or back of the rack for ease of installation and troubleshooting. They also feature an input monitoring
port for troubleshooting and diagnostics in the RF plant.
The SRF1 series is housed in a 1RU frame and the SRF3 series are housed in a 3RU frame. RF
specifications are dependent on the split / combine ratio. The list below includes all possible options of
the SRF splitter / combiners.
SRF1 SERIES:
SRF1-16-1x2 16-channel 1x2 splitter / 2x1 combiner
SRF1-8-1x4 8-channel 1x4 splitter / 4x1 combiner
SRF3 SERIES:
SRF3-64-1x2 64-channel 1x2 splitter / 2x1 combiner
SRF3-32-1x4 32-channel 1x4 splitter / 4x1 combiner

SRF Series Splitters and Combiners
SRF-2 Revision 0.1
1.1. BLOCK DIAGRAMS
COMMON
PORTA
PORTB
MON I T OR
-20dB
passive
tap
Figure 3: 1x2 Splitter / 2x1 Combiner
COMMON
PORTA
PORTB
-20dB
passive
tap PORTC
PORTD
MON I T O R
Figure 4: 1x4 Splitter / 4x1 Combiner

SRF Series Splitters and Combiners
Revision 0.1 SRF-3
1.2. TYPICAL APPLICATION DIAGRAM
Figure 1 illustrates the use of four SRF3-64-1x2 modules to achieve a 128x128 router using four XRF6 L
band routers. On the input side, the SRF functions as a splitter and as a combiner on the output side,
allowing non-blocking routing of any input to all outputs.
SCRF3-64-1x2
LbandInputs1-64 64
64
64
64
Outputs1-64
X6R F- PS
FRAME
STATUS
PSU
STATUS
ON O FF
PO WERSUPPLY
XRF6-FC
XRF6-I16LB
XRF6-
O16LB64x64
XRF6-I16LB XRF6-I16LB XRF6-I16LB
XRF6-
O16LB64x64
XRF6-
O16LB64x64
XRF6-
O16LB64x64
XRF6-FC
X6RF-PS
FRAME
STATUS
PSU
STATUS
ON OFF
POWER SUPPL Y
Power
Supply A
Power
SupplyB
Frame
Con trollerB
Frame
Co nt r o ll er A
S LOT 1 S LO T 2 SLOT 3 SL OT4SLOT5 S LOT 6 SLO T 7 S L OT 8
INPUTS
1-16
INPUTS
17-32
INPU TS
33-48
INPUTS
49 -64
OUTPU TS
17- 3 2
OUTPUTS
1- 16
OUTPUTS
33-48
OUTPUTS
49-64
X6R F- P S
FRAME
STATUS
PSU
STATUS
ON OFF
PO WER S UPP LY
XRF6-FC
XRF6-I16LB
XRF6-
O16LB64x64
XRF6-I16LB XRF6-I16LB XRF6 -I16LB
XRF6-
O16LB64x64
XRF6-
O16LB64x64
XRF6-
O16 LB64x64
XRF6-FC
X6RF-PS
FRAME
STATUS
PSU
STATUS
ON OFF
POWE R SUPPLY
Power
SupplyA
Power
SupplyB
Frame
ControllerB
Frame
Controlle r A
SLOT1 SLOT2SLOT3SLOT4SLOT5SLOT6SLOT 7 SLOT8
INPUTS
1-16
INPUTS
17- 32
INPUTS
33- 4 8
INPUTS
49-64
OUTPUTS
17- 32
OUTPUTS
1- 16
OUTPUTS
33- 48
OUTPUTS
49-64
XRF664x64Lbandrouter
X6R F- P S
FRAME
STATUS
PSU
STATUS
ON OFF
PO WER S UPP LY
XRF6-FC
XRF6-I16LB
XRF6 -
O16LB64x64
XRF6-I16LB XRF6-I16LB XRF6-I16LB
XRF6-
O16LB64x64
XRF6-
O16LB64x64
XRF6-
O16LB64x64
XRF6-FC
X6RF-PS
FRAME
STATUS
PSU
STATUS
ON OFF
POWE R SUPPLY
Power
SupplyA
Power
SupplyB
Frame
ControllerB
Frame
Controlle r A
SLOT1 SLOT2SLOT3SLOT4SLOT5SLOT6SLOT 7 SLOT8
INPUTS
1-16
INPUTS
17- 32
INPUTS
33- 4 8
INPUTS
49-64
OUTPUTS
17- 32
OUTPUTS
1- 16
OUTPUTS
33- 48
OUTPUTS
49-64
X6R F- P S
FRAME
STATUS
PSU
STATUS
ON OFF
PO WER S UPP LY
XRF6-FC
XRF6-I16LB
XRF6-
O16LB64x64
XRF6-I16LB XRF6-I16LB XRF6-I16LB
XRF6-
O16LB64x64
XRF6-
O16LB64x64
XRF6-
O16LB6 4 x64
XRF6-FC
X6RF-PS
FRAME
STATUS
PSU
STATUS
ON OFF
POWE R SUPPLY
Power
SupplyA
Power
SupplyB
Frame
ControllerB
Frame
Controlle r A
SLOT1 SLOT2SLOT3SLOT4SLOT5SLOT6SLOT 7 SLOT8
INPUTS
1-16
INPUTS
17- 32
INPUTS
33- 4 8
INPUTS
49-64
OUTPUTS
17- 32
OUTPUTS
1- 16
OUTPUTS
33- 48
OUTPUTS
49-64
SCRF3-64-1x2
LbandInputs65-128
64
64
SCRF3-64-1x2
SCRF3-64-1x2
64
64
Outputs65-128
Figure 5: 128x128 L band matrix using XRF6 64x64 routers and SRF3-64-1x2 modules.
2. INSTALLATION
The SRF splitters and combiners have RF coaxial connectors on the front and back side of the chassis.
The input ( common ) and monitoring ports are on the front of the panel. Output connectors are located on
the rear side of the chassis.
The monitoring port can be used for diagnostics and monitoring. This port is a –20dB tap of the common
port. Terminate this port with a 75 Ohm load when not connected.
Please note all unused outputs on a channel ( including monitoring outputs ) must be
terminated with a 75 Ohm load if they are not connected. Please contact Evertz
Microsystems for recommended termination suppliers.
"

SRF Series Splitters and Combiners
SRF-4 Revision 0.1
Figure 6: Front Panel of SRF3-64-1x2 chassis
Figure 7: Rear Panel of SRF3-64-1x2 chassis

SRF Series Splitters and Combiners
Revision 0.1 SRF-5
3. SPECIFICATIONS
3.1. RF INPUT/OUTPUT
Inputs: 16 ( SRF1-16-1x2 )
8 ( SRF1-8-1x4 )
64 ( SRF3-64-1x2 )
32 ( SRF3-32-1x4 )
Outputs: 32 ( SRF1-16-1x2 )
32 ( SRF1-8-1x4 )
128 ( SRF3-64-1x2 )
128 ( SRF3-32-1x4 )
Connectors: BNC per IEC 60169-8 Amendment 2 ( F type optional )
Frequency Range: 40MHz to 3000MHz
Insertion Loss: 4.2dB ± 0.5dB ( 1 x 2 )
7.5dB ± 0.75dB ( 1 x 4 )
Return Loss (inputs and outputs): > 15 dB (250MHz-3000MHz)
Isolation: > 17 dB ( Output to Output on same channel - 550MHz to 3000MHz)
> 60 dB ( Channel to any other Channel )
Monitoring Output: -20dB relative to common port
Note: SRF passes LNB power and DiSEqC signals.
3.2. PHYSICAL
SRF1: 1.75" ( 44.5mm ) H x 19" ( 483mm ) W x 5.5" ( 140mm ) D
SRF3: 5.25" ( 133mm ) H x 19" ( 483mm ) W x 5.5" ( 140mm ) D

SRF Series Splitters and Combiners
Revision 0.1 SRF-1
This page left intentionally blank