evertz 8150 User manual

Model 8150
Digital Afterburner
Instruction Manual
© Copyright 1998
EVERTZ MICROSYSTEMS LTD.
5288 John Lucas Drive, Burlington, Ontario, Canada, L7L 5Z9
Phone: [phone] Fax: [phone]
BBS: 905-335-9131
Internet: Tech Support: [email protected]
Sales: [email protected]
Web Page: http://www.evertz.com
Revision 1.0,July 1998
The material contained in this manual consists of information that is the property of Evertz Microsystems and is
intended solely for the use of purchasers of the 8150 Digital Afterburner. Evertz Microsystems expressly prohibits
the use of this manual for any purpose other than the operation of the 8150.
All rights reserved. No part of this publication may be reproduced without the express written permission of Evertz
Microsystems Ltd. Copies of this guide can be ordered from your Evertz products dealer or from Evertz
Microsystems.

INFORMATION TO USERS IN EUROPE
NOTE
CISPR 22 CLASS A DIGITAL DEVICE OR PERIPHERAL
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to the European Union EMC directive. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation
of this equipment in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own expense.
INFORMATION TO USERS IN THE U.S.A.
NOTE
FCC CLASS A DIGITAL DEVICE OR PERIPHERAL
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
WARNING
Changes or Modifications not expressly approved by Evertz Microsystems Ltd. could
void the user’s authority to operate the equipment.
Use of unshielded plugs or cables may cause radiation interference. Properly shielded
interface cables with the shield connected to the chassis ground of the device must be
used.

Model 8150 Digital Afterburner Manual
REVISION HISTORY
REVISION DESCRIPTION DATE
1.0 Original issue July 98

Model 8150 Digital Afterburner Manual
This page left intentionally blank

Model 8150 Digital Afterburner Manual
TABLE OF CONTENTS i
TABLE OF CONTENTS
1. OVERVIEW.................................................................................................................................. 1-1
1.1. HOW TO USE THIS MANUAL .................................................................................................... 1-2
1.2. DEFINITIONS .............................................................................................................................. 1-2
2. INSTALLATION........................................................................................................................... 2-1
2.1. REAR PANEL.............................................................................................................................. 2-1
2.1.1. Digital Video Connections ............................................................................................. 2-1
2.1.2. Analog Monitor Connections (8150-MON option) ......................................................... 2-1
2.1.3. Power Connections ....................................................................................................... 2-1
2.1.4. Remote Control Connections ........................................................................................ 2-2
2.2. MOUNTING ................................................................................................................................. 2-2
2.3. POWER REQUIREMENTS .........................................................................................................2-2
2.3.1. Selecting the Correct Mains Voltage............................................................................. 2-2
2.3.2. Changing the Fuse........................................................................................................2-3
2.4. CONNECTING THE DIGITAL VIDEO ......................................................................................... 2-3
2.4.1. Video Input .................................................................................................................... 2-3
2.4.2. Video Output ................................................................................................................. 2-4
2.5. TYPICAL APPLICATION ............................................................................................................ 2-4
3. HOW TO OPERATE THE DIGITAL AFTERBURNER ................................................................ 3-1
3.1. AN OVERVIEW OF KEY AND DISPLAY FUNCTIONS.............................................................. 3-1
3.1.1. Overview of the Pushbuttons ........................................................................................ 3-1
3.1.2. Overview of the Shifted Key Functions ......................................................................... 3-2
3.1.3. Status Indicators ........................................................................................................... 3-3
3.2. FRONT PANEL DISPLAY FUNCTIONS ..................................................................................... 3-3
3.2.1. Front Panel Drop Frame Indicators (NTSC Only) ......................................................... 3-4
3.3. AN OVERVIEW OF THE FRONT PANEL PROGRAMMING MENU .......................................... 3-4
3.3.1. Engineering Setup Menu............................................................................................... 3-6
3.4. ASSIGNING THE OVERALL FUNCTIONS OF THE READERS................................................ 3-7
3.5. SETTING UP THE INDIVIDUAL READERS ............................................................................... 3-8
3.5.1. Selecting the Format of the Time and User Bit Data..................................................... 3-8
3.5.2. Setting The VITC Reader Line Range .......................................................................... 3-9
3.5.3. Selecting the VITC CRC ............................................................................................... 3-9
3.5.4. Controlling the ‘Look ahead’ Compensation ............................................................... 3-10

Model 8150 Digital Afterburner Manual
TABLE OF CONTENTS ii
3.5.5. Selecting the Film Related Modes .............................................................................. 3-10
3.6. OPERATING THE 8150 IN 3 LINE VITC MODE....................................................................... 3-12
3.6.1. Setting The VITC Reader Line Range - 3 Line VITC Mode ........................................ 3-13
3.6.2. Controlling the ‘Look ahead’ Compensation - 3 Line VITC Mode ............................... 3-13
3.7. PROGRAMMING THE ENGINEERING SETUP FUNCTIONS.................................................. 3-14
3.7.1. Selecting the Video Type ............................................................................................ 3-14
3.7.2. Adjusting the Front Panel Display Brightness ............................................................. 3-14
3.7.3. Displaying the 8150 Software version......................................................................... 3-14
3.7.4. Selecting the Character Size....................................................................................... 3-14
3.7.5. Selecting the Character Style...................................................................................... 3-15
3.7.6. Selecting whether the Frames, Fields and Symbols will be displayed on the VCG .... 3-15
3.7.7. Testing the Data Memory............................................................................................ 3-16
3.7.8. Resetting the 8150 to Factory Defaults....................................................................... 3-16
3.8. CHARACTER GENERATOR FUNCTIONS .............................................................................. 3-16
3.8.1. Selecting and Positioning the Individual Character Inserter Windows ........................ 3-17
3.8.2. Positioning the Overall Character Display................................................................... 3-17
3.8.3. Making Fine Adjustments To The Character Generator Raster Position .................... 3-17
3.8.4. VCG Drop Frame Indicators (NTSC Only) .................................................................. 3-17
3.8.5. VCG Field Identification .............................................................................................. 3-18
3.9. STORING & RECALLING USER CONFIGURATIONS ............................................................ 3-18
3.9.1. Storing User Configurations ........................................................................................ 3-18
3.9.2. Recalling User Configurations..................................................................................... 3-18
4. TECHNICAL DESCRIPTION....................................................................................................... 4-1
4.1. OVERVIEW.................................................................................................................................. 4-1
4.2. JUMPERS AND SWITCHES.......................................................................................................4-1
4.2.1. DIP Switch Functions .................................................................................................... 4-1
4.2.2. Jumper Functions - Main Board .................................................................................... 4-1
4.3. CIRCUIT DESCRIPTION............................................................................................................. 4-2
4.3.1. Microcontroller (8025-36) .............................................................................................. 4-2
4.3.2. Front Panel Display and Pushbuttons (5220-31) .......................................................... 4-3
4.3.3. Serial Digital Video Input (8025-33) .............................................................................. 4-4
4.3.4. Serial Digital Video Output (8025-34) ........................................................................... 4-5
4.3.5. VITC Reader/Character Generator Logic (8037-31, 8037-32, 8037-33)....................... 4-5
4.3.6. Keyer LCA (8025-32, 8025-35, 8025-37)...................................................................... 4-6
4.3.7. Analog Monitor Output - optional (8029-31, 8029-32)................................................... 4-7

Model 8150 Digital Afterburner Manual
TABLE OF CONTENTS iii
Figures
Figure 2-1: 8150 Rear Panel........................................................................................................ 2-1
Figure 2-2: Typical Application of 8150 for Character Generation............................................... 2-4
Figure 3-1: Front Panel Layout .................................................................................................... 3-1
Figure 3-2: Overview of the 8150 Programming Menu System ................................................... 3-5
Figure 3-3 Overview of the 8150 Engineering Menu ................................................................... 3-7
Figure 4-1: DIP Switch Functions ................................................................................................4-1
Figure 4-2: Block Diagram ........................................................................................................... 4-3
Tables
Table 4-1: Keyboard Scan Codes................................................................................................ 4-4
Drawings .................................................................................................................................... Drawing #
Parallel Video I/O Schematic ............................................................................................. 8025-31F
Serial / Parallel Mux and I/O Schematic ............................................................................ 8025-32F
Serial Video Input Schematic............................................................................................. 8025-33F
Serial Video Output Schematic .......................................................................................... 8025-34F
Digital Video LCA Schematic ............................................................................................. 8025-35F
Microprocessor and EPROM Schematic ........................................................................... 8025-36F
Monitor submodule Header, Tri Oscillator and Control Inputs Schematic ........................ 8025-37F
Power Supply DIP Switch and Display Header Schematic................................................ 8025-38F
Clock Buffer and Phase Restorer Schematic..................................................................... 8025-39F
Main Board Component Layout ....................................................................................... 8025-83F1
Video Encoder ...................................................................................................................8029-30B
Digital I/O & Submodule Headers ......................................................................................8029-31B
Optional CC D’Code Circuit ...............................................................................................8029-32B
8029 Top Component Layout ............................................................................................8029-80B
8029 Bottom Component Layout .......................................................................................8029-81B
VITC Reader / Character Generator Submodule Memory & Serial I/O Circuits.................8037-31B
VITC Reader / Character Generator Submodule LTC Input Circuitry................................8037-32B
VITC Reader / Character Generator Submodule VITC/Char Output Circuitry...................8037-33B
VITC Reader / Character Generator Submodule LCA Circuit............................................8037-34B
VITC Reader / Character Generator Submodule
Optional Colour Frame & Ref Video Circuit ...........................................................8037-35B
VITC Reader / Character Generator Submodule Sub-Module Header..............................8037-36B
VITC Reader / Character Generator Submodule Component Layout ...............................8037-82B
5220 Display Board Schematic..........................................................................................5220-31C
5220 Display Board Component Layout ............................................................................5220-89C
8102 Power Supply Schematic ..........................................................................................8102-31A
8102 Power Supply Component Layout ............................................................................8102-80A

Model 8150 Digital Afterburner Manual
TABLE OF CONTENTS iv
This page left intentionally blank

Model 8150 Digital Afterburner Manual
1. OVERVIEW.................................................................................................................................. 1-1
1.1. HOW TO USE THIS MANUAL .................................................................................................... 1-2
1.2. DEFINITIONS .............................................................................................................................. 1-2

Model 8150 Digital Afterburner Manual
This page left intentionally blank

Model 8150 Digital Afterburner Manual
OVERVIEW Page 1-1
1. OVERVIEW
The 8150 Digital Afterburner is a multi-purpose Digital VITC Reader and
character inserter that extracts the vertical interval timecode directly from
the digital bitstream. A 16 digit alphanumeric display can be quickly
delegated to show the required data. The Digital Afterburner contains
three separate VITC readers that can be operated independently of each
other. The Digital Afterburner can be configured in one of two basic
operating modes:
•Triple VITC reader - reads VITC from three sets of lines on the
same video simultaneously - each reader controlled separately
•Three Line VITC reader - reads 3 line VITC standard generated
by 4025 Film Footage Encoder - the 3 readers have common
controls. Most reader settings are automatically detected from
the 3 line VITC
The Digital Afterburner is designed to work as a companion to the Evertz
4015 and 4025 Film Footage Encoders. Film edge numbers (KeyKode)
which have been encoded into the user bits can be recovered and
displayed in standard film format notations as are used by the Film Footage
Encoder. In NTSC 24 frame per second transfers, the 3/2 pulldown
information is recovered from the encoded user bits and displayed in
standard A, B, C, D film frame type convention, when the incoming code is
at play speed. The Digital Afterburner reads edge numbers encoded using
the proprietary 2 line Evertz and the industry standard 3 line VITC encoding
schemes and can display pulldown information from the VITC in all speeds.
This permits unambiguous identification of the film frame pulldown when
the VTR is parked on any frame.
The model 8150 VITC reader's line range can be easily programmed from
the front panel, thus permitting recovery of specific VITC data where
multiple sets have been recorded.
Features:
• Standard unit is equipped for component digital video.
• Serial digital video input provides automatic cable equalization on cable
lengths up to 200 meters of low loss coax such as Belden 8281
• Serial digital video output provides two separate outputs
• Passes embedded audio and other ancillary data signals
• Rack mountable
• 8 or 10 bit resolution
• 16 digit Alpha-numeric display, with 16 pushbuttons
• High resolution character inserter provides up to six independently
positionable windows to show time and user bits simultaneously.
• Three character sizes and the choice of white or black characters with
or without contrasting background mask are selected from the front
panel.

Model 8150 Digital Afterburner Manual
OVERVIEW Page 1-2
1.1. HOW TO USE THIS MANUAL
This manual is organized into 4 chapters: Overview, Installation, Operation
and Technical Description.
Items of special note are indicated with a double box like this.
1.2. DEFINITIONS
AES: (Audio Engineering Society): A professional organization
that recommends standards for the audio industries.
AES/EBU: Informal name for a digital audio standard established jointly by
the Audio Engineering Society and the European Broadcasting
Union organizations.
ANALOG: An adjective describing any signal that varies continuously as
opposed to a digital signal that contains discrete levels
representing digits 0 and 1.
A-TO D CONVERTER (ANALOG-TO-DIGITAL): A circuit that uses
digital sampling to convert an analog signal into a digital
representation of that signal.
BIT: A binary representation of 0 or 1. One of the quantized levels of
a pixel.
BIT PARALLEL: Byte-wise transmission of digital video down a multi-
conductor cable where each pair of wires carries a single bit.
This standard is covered under SMPTE 125M, EBU 3267-E and
CCIR 656.
BIT SERIAL: Bit-wise transmission of digital video down a single
conductor such as coaxial cable. May also be sent through
fiber optics. This standard is covered under SMPTE 259M and
CCIR 656.
BIT STREAM:A continuous series of bits transmitted on a line.
BNC: Abbreviation of "baby N connector". A cable connector used
extensively in television systems.
BYTE: A complete set of quantized levels containing all the bits. Bytes
consisting of 8 to 10 bits per sample are typical in digital video
systems.
"

Model 8150 Digital Afterburner Manual
OVERVIEW Page 1-3
CABLE EQUALIZATION: The process of altering the frequency
response of a video amplifier to compensate for high frequency
losses in coaxial cable.
CCIR (International Radio Consultative Committee) An international
standards committee. (This organization is now known as ITU.)
CCIR-601: (This document now known as ITU-R601). An international
standard for component digital television from which was
derived SMPTE 125M and EBU 3246-E standards. CCIR-601
defines the sampling systems, matrix values and filter
characteristics for both Y, B-Y, R-Y and RGB component digital
television signals.
CCIR-656 (This document now known as ITU-R656). The physical parallel
and serial interconnect scheme for CCIR-601. CCIR-656
defines the parallel connector pinouts as well as the blanking,
sync and multiplexing schemes used in both parallel and serial
interfaces. It reflects definitions found in EBU Tech 3267 (for
625 line systems) and SMPTE 125M (parallel 525 line systems)
and SMPTE 259M (serial 525 line systems).
CLIFF EFFECT (also referred to as the ‘digital cliff’) This is a
phenomenon found in digital video systems that describes the
sudden deterioration of picture quality when due to excessive bit
errors, often caused by excessive cable lengths. The digital
signal will be perfect even though one of its signal parameters is
approaching or passing the specified limits. At a given moment
however, the parameter will reach a point where the data can no
longer be interpreted correctly, and the picture will be totally
unrecognizable.
COMPONENT ANALOG: The non-encoded output of a camera, video
tape recorder, etc., consisting of the three primary colour
signals: red, green, and blue (RGB) that together convey all
necessary picture information. In some component video
formats these three components have been translated into a
luminance signal and two colour difference signals, for example
Y, B-Y, R-Y.
COMPONENT DIGITAL: A digital representation of a component
analog signal set, most often Y, B-Y, R-Y. The encoding
parameters are specified by CCIR-601. CCIR-656 and SMPTE
125M specify the parallel interface.
COMPOSITE ANALOG: An encoded video signal such as NTSC or
PAL video, that includes horizontal and vertical synchronizing
information.

Model 8150 Digital Afterburner Manual
OVERVIEW Page 1-4
COMPOSITE DIGITAL: A digitally encoded video signal, such as
NTSC or PAL video that includes horizontal and vertical
synchronizing information.
D1: A component digital video recording format that uses data
conforming to the CCIR-601 standard. Records on 19 mm
magnetic tape. (Often used incorrectly to refer to component
digital video.)
D2: A composite digital video recording format that uses data
conforming to SMPTE 244M. Records on 19 mm magnetic
tape. (Often used incorrectly to refer to composite digital video.)
D3: A composite digital video recording format that uses data
conforming to SMPTE 244M. Records on 1/2" magnetic tape.
EBU (European Broadcasting Union): An organization of European
broadcasters that among other activities provides technical
recommendations for the 625/50 line television systems.
EBU TECH 3267-E: The EBU recommendation for the parallel interface
of 625 line digital video signal. This is a revision of the earlier
EBU Tech 3246-E standard that was in turn derived from CCIR-
601.
EDH Error Detection and Handling (EDH) is defined in SMPTE
RP-165 as a method of determining when bit errors have
occurred along the digital video path. According to RP-165, two
error detection checkwords are used, one for active picture
samples, and the other on a full field of samples. Three sets of
flags are used to convey information regarding detected errors,
to facilitate identification of faulty equipment or cabling. One set
of flags is associated with each checkword, and the third is used
to evaluate ancillary data integrity. The checkwords and flags
are combined into a special error-detection data packet that is
included as ancillary data in the serial digital signal.
EMBEDDED AUDIO: Digital audio is multiplexed onto a serial digital video
data stream.
ITU: The United Nations regulatory body governing all forms of
communications. ITU-R (previously CCIR) regulates the radio
frequency spectrum, while ITU-T (previously CCITT) deals with
the telecommunications standards.
ITU-R601: See CCIR601
PIXEL: The smallest distinguishable and resolvable area in a video
image. A single point on the screen. In digital video, a single
sample of the picture. Derived from the words picture element.

Model 8150 Digital Afterburner Manual
OVERVIEW Page 1-5
RESOLUTION: The number of bits (four, eight, ten, etc.) determines
the resolution of the signal. Eight bits is the minimum resolution
for broadcast television signals.
4 bits = a resolution of 1 in 16.
8 bits = a resolution of 1 in 256.
10 bits = a resolution of 1 in 1024.
SERIAL DIGITAL: Digital information that is transmitted in serial form.
Often used informally to refer to serial digital television signals.
SMPTE (Society of Motion Picture and Television Engineers): A
professional organization that recommends standards for the
film and television industries.
SMPTE 125M: The SMPTE standard for bit parallel digital interface
for component video signals. SMPTE 125M defines the
parameters required to generate and distribute component
video signals on a parallel interface.
SMPTE 244M: The SMPTE standard for bit parallel digital interface
for composite video signals. SMPTE 244M defines the
parameters required to generate and distribute composite video
signals on a parallel interface.
SMPTE 259M: The SMPTE standard for 525 line serial digital
component and composite interfaces.
TRS: Timing reference signals used in composite digital systems.
(It is four words long).
TRS-ID: Abbreviation for "Timing Reference Signal Identification". A
reference signal used to maintain timing in composite digital
systems. (It is four words long.)
4:2:2 A commonly used term for a component digital video format.
The details of the format are specified in the CCIR-601
standard. The numerals 4:2:2 denote the ratio of the sampling
frequencies of the luminance channel to the two colour
difference channels. For every four luminance samples, there
are two samples of each colour difference channel.
4Fsc Four times subcarrier sampling rate uses in composite digital
systems. In NTSC this is 14.3 MHz. In PAL this is 17.7 MHz.

Model 8150 Digital Afterburner Manual
OVERVIEW Page 1-6
This page left intentionally blank

Model 8150 Digital Afterburner Manual
INSTALLATION Page 2-1
2. INSTALLATION
2.1. REAR PANEL
MONITOR
V
IDEOIN
.25 A
.125 A
230V:
115V:
FUSE
VIDEO
PARALLEL
SERIAL
REMOTE CONTROL
model 8150
DIGITAL AFTERBURNER MADE IN CANADA
EVERTZ MICROSYSTEMS LTD
SDI
VIDEO OUT
SDI
Figure 2-1: 8150 Rear Panel
The following sections describe the purpose of the rear panel connectors of
the 8150. Sections 2.1.1 to 2.1.2 describe the specific signals that should
be connected to the 8150.
2.1.1. Digital Video Connections
VIDEO IN SDI: A BNC connector for input of 10 bit serial digital
video signals compatible with the SMPTE 259M standard.
VIDEO OUT SDI: Two BNC connectors for output of 10 bit serial digital
video signals compatible with the SMPTE 259M standard. This
video will be the video input with characters inserted onto it.
2.1.2. Analog Monitor Connections (8150-MON option)
The analog composite monitor output is optional and may not be fitted on
your unit.
MONITOR VIDEO: A BNC output of the optional composite analog
encoder.
2.1.3. Power Connections
LINE: The 8150 may be set for either 115v/60 Hz or 230v/50 Hz AC
operation. The voltage selector switch is accessible on the rear
panel. The line voltage connector contains an integral slow
blow fuse (and a spare one).

Model 8150 Digital Afterburner Manual
INSTALLATION Page 2-2
2.1.4. Remote Control Connections
SERIAL: A 9-pin female 'D' connector for RS232/422 communications to a
computer (Future Use)
Pin Description
1 Ground
2 RS-422 Transmit A(-)
3 RS-422 Receive B(+)
4 Receive Common
5 RS-232 Transmit
6 Transmit Common
7 RS-422 Transmit B(+)
8 RS-232 Receive and RS-422 Receive A(-)
9 Ground
PARALLEL: A 9 pin female 'D' connector for connection to 'closure to
ground' remote control signals. Each input has an internal 47 K
ohm pull-up to +5 volts. (Future Use)
2.2. MOUNTING
The 8150 Digital VITC Reader is equipped with rack mounting angles and
fits into a standard 19 inch by 1 3/4 inch (483 mm x 45 mm) rack space.
The mounting angles may be removed if rack mounting is not desired.
2.3. POWER REQUIREMENTS
2.3.1. Selecting the Correct Mains Voltage
Power requirements are 115 or 230 volts AC at 50 or 60 Hz, switch
selectable on the rear panel. Power should be applied by connecting a 3-
wire grounding type power supply cord to the power entry module on the
rear panel. The power cord should be minimum 18 AWG wire size; type
SST marked VW-1, maximum 2.5 m in length.
Before connecting the line power, be sure to select the proper line voltage.
Also, check that the line fuse is rated for the correct value marked on the
rear panel.
The power entry module combines a standard IEC 320 power inlet
connector, voltage selector switch, two 5 x 20 mm fuse holders (one active,
one spare) and an EMI line filter.
!

Model 8150 Digital Afterburner Manual
INSTALLATION Page 2-3
To change the mains voltage setting, open the cover of the power entry
module using a small screwdriver. Remove the drum selector switch, and
re-insert it so that the desired voltage is visible through the opening on the
mains connector cover. Check that the correct fuse is in use as shown in
section below.
2.3.2. Changing the Fuse
The fuse holder is located inside the power entry module. To change the
fuse, open the cover of the power entry module using a small screwdriver.
The fuse holder on the bottom contains the active fuse. The one at the top
contains a spare fuse. Pull the bottom fuse holder out and place a fuse of
the correct value in it. Use slo blo (time delay) 5 x 20 mm fuses rated for
250 Volts with the following current ratings:
For 115 Volt operation 250 mA
For 230 Volt operation 125 mA
Make sure that the arrow is pointing down when you replace the fuse
holder. Close the door on the power entry module and connect the mains
voltage.
Never replace with a fuse of greater value.
2.4. CONNECTING THE DIGITAL VIDEO
2.4.1. Video Input
The 8150 requires that a digital video source be connected to the VIDEO
IN SDI video input. The 8150 may be configured to accept either 525 or
625 line digital video in the component (4:2:2) format. The VIDEO TYPE
parameter on the front panel menu must be set correctly to match the video
input. (See section 3.7.1 for information on changing the video type
setting).
The 4:2:2 and 4 Fsc LED's indicate which input is active. The VIDEO LED
indicates that there is video present. When it is blinking it indicates that
there is no video present.
2.4.2. Video Output
The VIDEO OUT SDI outputs contain the input video with character data
keyed in by the keyer. Connect one of these outputs to any input on your
system that accepts 8 or 10 bit SERIAL digital video. Two identical VIDEO
OUT SDI digital video outputs are provided.
!

Model 8150 Digital Afterburner Manual
INSTALLATION Page 2-4
2.5. TYPICAL APPLICATION
MONITOR
VIDEO IN
.25 A
.125 A
230V:
115V:
FUSE
VIDEO
PARALLEL
SERIAL
REMOTE CONTROL
model 8150
SERIAL DIGITAL
VIDEO + CHARACTERS SERIAL DIGITAL
VIDEO SOURCE
12:45:30:00
DIGITAL VIDEO MONITOR
DIGITAL AFTERBURNER MADE IN CANADA
EVERTZ MICROSYSTEMS LTD
SDI
VIDEO OUT
SDI
Figure 2-2: Typical Application of 8150 for Character Generation