EWM TIG 17 G User manual

EWM
HIGHTEC WELDING GmbH
Dr. Günter-Henle-Straße 8 • D-56271 Mündersbach
Fon [phone] • Fax [phone]
www.ewm.de • [e-mail]
GB
Operating instructions
TIG welding torch
TIG 17 G
TIG 26 G
TIG 150 G
TIG 200 G
N. B. These operating instructions must be read before commissioning.
Failure to do so may be dangerous.
Machines may only be operated by personnel who are familiar with the appropriate safety
regulations.
The machines bear the conformity mark and thus comply with the
• EC Low Voltage Directive (2006/95/ EG)
• EC EMC Directive (2004/108/ EG)
©The content of the operating instructions does not constitute grounds for any claims on the part
of the buyer.
The copyright to these operating instructions remains with the manufacturer.
Reprinting, including extracts, only with written approval.
© 2008 Subject to alteration. Item No.:099-011623-EWM01 Revised: 21.10.2008

Contents
Notes on the use of these operating instructions
2 Item No.:099-011623-EWM01
1Contents
1Contents..................................................................................................................................................2
2Safety instructions.................................................................................................................................3
2.1 Notes on the use of these operating instructions...........................................................................3
2.2 General...........................................................................................................................................4
2.3 Transport and installation...............................................................................................................5
2.3.1 Scope of delivery............................................................................................................5
2.4 Ambient conditions.........................................................................................................................6
2.4.1 In operation.....................................................................................................................6
2.4.2 Transport and storage ....................................................................................................6
2.5 Proper usage..................................................................................................................................6
3Technical data.........................................................................................................................................7
4Machine description...............................................................................................................................8
4.1 TIG 17, TIG 26, TIG 150, TIG 200.................................................................................................8
4.2 Connection variants .......................................................................................................................9
5Commissioning.......................................................................................................................................9
5.1 General...........................................................................................................................................9
5.2 Area of application – proper usage................................................................................................9
5.3 Equipping the torch......................................................................................................................10
5.3.1 TIG 17, 26.....................................................................................................................10
5.3.2 TIG 150, 200.................................................................................................................11
6Functional characteristics...................................................................................................................12
6.1 General.........................................................................................................................................12
6.2 TIG torch ......................................................................................................................................12
6.3 TIG Up/Down torch ......................................................................................................................13
6.4 TIG Retox torch............................................................................................................................14
7Maintenance and testing .....................................................................................................................15
7.1 Daily maintenance tasks..............................................................................................................15
7.2 Monthly maintenance tasks..........................................................................................................15
7.3 Repair Work .................................................................................................................................15
7.4 Disposing of equipment................................................................................................................15
8Operating problems, causes and remedies.......................................................................................16
8.1 Customer checklist.......................................................................................................................16
9Warranty................................................................................................................................................17
10 Replaceable parts.................................................................................................................................18
10.1 TIG 17 ..........................................................................................................................................18
10.2 TIG 26 ..........................................................................................................................................19
10.3 TIG 150 ........................................................................................................................................20
10.4 TIG 200 ........................................................................................................................................21
11 Appendix A............................................................................................................................................22
11.1 Declaration of Conformity.............................................................................................................22

Safety instructions
Notes on the use of these operating instructions
Item No.:099-011623-EWM01 3
2Safety instructions
2.1 Notes on the use of these operating instructions
These operating instructions are arranged into chapters.
For ease of navigation, there are also occasional symbols for especially important text passages on the
edge of the pages in addition to sub-headings.
Technical features which users must observe.
The safety instructions are categorised as follows according to importance:
CAUTION
Working and operating procedures which must be followed precisely to avoid damaging
or destroying the product.
• The safety information includes the "CAUTION" keyword in its heading without a general
warning symbol.
• The hazard is explained using a symbol at the edge of the page.
CAUTION
Working or operating procedures which must be closely observed to prevent possible
minor personal injury.
• The safety information includes the "CAUTION" keyword in its heading with a general
warning symbol.
• The risk is explained using a symbol on the edge of the page.
CAUTION
Working or operating procedures which must be closely observed to prevent serious
personal injury.
• The safety information includes the "WARNING" keyword in its heading with a general
warning symbol.
• The risk is also explained using a symbol on the edge of the page.
DANGER
Working or operating procedures which must be closely observed to prevent serious
personal injury.
• The safety information includes the "DANGER" keyword in its heading with a general
warning symbol.
• The risk is also explained using a symbol on the edge of the page.
Instructions and lists detailing step-by-step actions in given situations can be recognised by bullet points,
e.g.:
• Insert the welding current lead socket into the relevant socket and lock.
Symbol Description
Press
Do not press
Turn
Switch

Safety instructions
General
4 Item No.:099-011623-EWM01
2.2 General
CAUTION
Obligations of the operator!
In the European Economic Area (EEA), the relevant national version of the basic
guidelines must be followed and observed!
• National version of the basic guidelines (89/391/EEC) as well as the relevant individual
guidelines.
• In particular the Directive (89/655/EEC) on the minimum regulations for safety and health
protection when staff members are using equipment during work.
• The accident prevention regulations of the relevant country (e.g. in Germany, BGV D 1).
• Check at regular intervals that users are working in a safety-conscious way!
We can only guarantee the perfect functioning of our products when used with system
components and options from our own range of products!
Trained personnel!
Commissioning is reserved for persons who have the relevant expertise of working with
arc welding machines.
CAUTION
Noise exposure!
Noise exceeding 70 dBA can cause permanent hearing damage!
• Wear suitable ear protection!
• Persons located within the working area must wear suitable ear protection!
CAUTION
Risk of accidents if these safety instructions are not observed!
Non-observance of these safety instructions is potentially fatal!
• Carefully read the safety information in this manual!
• Observe the accident prevention regulations in your country.
• Inform persons in the working area that they must observe the regulations!
Fire hazard!
Flames may arise as a result of the high temperatures, stray sparks, glowing-hot parts
and hot slag produced during the welding process.
Stray welding currents can also result in flames forming!
• Check for fire hazards in the working area!
• Do not carry any easily flammable objects such as matches or lighters.
• Keep appropriate fire extinguishing equipment to hand in the working area!
• Thoroughly remove any residue of flammable substances from the workpiece before starting
welding.
• Only continue work on welded workpieces once they have cooled down.
Do not allow to come into contact with flammable material!
• Connect welding leads correctly!
Risk of injury due to radiation or heat!
Arc radiation results in injury to skin and eyes.
Contact with hot workpieces and sparks results in burns.
• Wear dry protective clothing (e.g. welding shield, gloves, etc.) according to the relevant
regulations in the country in question!
• Protect persons not involved in the work against arc beams and the risk of glare using safety
curtains!

Safety instructions
Transport and installation
Item No.:099-011623-EWM01 5
DANGER
Electric shock!
Welding machines use high voltages which can result in potentially fatal electric shocks
and burns on contact. Even low voltages can cause you to get a shock and lead to
accidents.
• Do not touch any live parts in or on the machine!
• Connection cables and leads must be free of faults!
• Switching off alone is not sufficient! Wait for 2 minutes until the capacitors have discharged.
• Place welding torch and stick electrode holder on an insulated surface!
• The unit should only be opened by specialist staff after the mains plug has been unplugged!
• Only wear dry protective clothing!
Electromagnetic fields!
The power source may cause electrical or electromagnetic fields to be produced which
could affect the correct functioning of electronic equipment such as IT, CAD devices,
telecommunication lines, power cables, signal lines and pacemakers.
• Observe the maintenance instructions! (see Maintenance and Testing chapter)
• Unwind welding lines completely!
• Shield devices or equipment sensitive to radiation accordingly!
• The correct functioning of pacemakers may be affected (obtain advice from a health
professional if necessary).
Validity of this document!
This document describes an accessory and is only valid in combination with the
operating instructions for the power source being used (welding machine)!
• Read the operating instructions, in particular the safety instructions for the power source
(welding machine)!
Proper usage!
The machine has been manufactured according to the latest developments in technology and
current regulations and standards. It is to be operated only for the use for which it was designed
(see chapter Commissioning/Area of application). If the machine is not used properly, danger may
be caused to persons, animals and material objects due to this machine.
• The machine must only be used in line with proper usage and by trained or expert staff!
• No improper or conversion work is not permitted!
2.3 Transport and installation
CAUTION
Damage due to supply lines not being disconnected!
During transport, supply lines which have not been disconnected (mains supply leads,
control leads, etc.) may cause hazards such as connected equipment tipping over and
injuring persons!
• Disconnect supply lines!
2.3.1 Scope of delivery
The delivery is checked and packaged carefully before dispatch, however it is not possible to exclude the
possibility of damage during transit.
Receiving inspection
• Check that the delivery is complete using the delivery note!
In the event of damage to the packaging
• Check the delivery for damage (visual inspection)!
In the event of complaints
If the delivery has been damaged during transport:
• Please contact the last haulier immediately!
• Keep the packaging (for possible checking by the haulier or for the return shipment).
Packaging for returns

Safety instructions
Ambient conditions
6 Item No.:099-011623-EWM01
If possible, please use the original packaging and the original packaging material. If you have any queries
on packaging and protection during transport, please contact your supplier.
2.4 Ambient conditions
CAUTION
Equipment damage due to dirt accumulation!
Unusually high quantities of dust, acid, corrosive gases or substances may damage the
equipment.
• Avoid high volumes of smoke, vapour, oil vapour and grinding dust!
• Avoid ambient air containing salt (sea air)!
2.4.1 In operation
Temperature range of the ambient air:
• -10 °C to +40 °C
Relative air humidity:
• Up to 50% at 40 °C
• Up to 90% at 20 °C
2.4.2 Transport and storage
Storage in an enclosed space, temperature range of the ambient air:
• -25 °C to +55 °C
Relative air humidity
• Up to 90% at 20 °C
2.5 Proper usage
Proper usage!
The machine has been manufactured according to the latest developments in technology and
current regulations and standards. It is to be operated only for the use for which it was designed
(see chapter Commissioning/Area of application). If the machine is not used properly, danger may
be caused to persons, animals and material objects due to this machine.
• The machine must only be used in line with proper usage and by trained or expert staff!
• No improper or conversion work is not permitted!

Technical data
Proper usage
Item No.:099-011623-EWM01 7
3Technical data
Type TIG 17 TIG 26 TIG 150 TIG 200
Poling of the electrode with
DC normally negative
Operation type hand-controlled
Duty cycle 35 %
Voltage measurement 113 V peak value
Max. arc ignition and
stabilisation voltage 12kV
Switching voltage key
button 0.02–42 V
Switching current key
button 0.01–100 mA
Switching output key
button max. 1 W (ohmic load)
Voltage type DC direct voltage or AC alternating voltage
Electrode types standard Tungsten electrodes
Ambient temperature -10 °C to +40 °C
Protection classification of
the machine-side
connections (EN 60529)
IP3X IP2X IP3X IP3X
Shielding gas Shielding gas DIN EN 439
Gas flow 10 to 20 l/min
Maximum welding current
(DC/AC) 140 A/100 A 180 A/130 A 150 A/105 A
with gas
nozzle, long
200 A/140 A
Tube package 4, 8 or 12 m
Tungsten electrodes 0.5–2.4 mm 0.5–4.0 mm 1.0–2.4 mm 1.6–3.2 mm
Connection Welding torch central connection
Constructed to standard DIN EN 60974-7

Machine description
TIG 17, TIG 26, TIG 150, TIG 200
8 Item No.:099-011623-EWM01
4Machine description
The TIG torches are available in different model versions. The up/down and Retox versions add extra
operating elements to the torches (see Function specification chapter).
4.1 TIG 17, TIG 26, TIG 150, TIG 200
4
3
2
1
4
3
2
1
TIG 17, TIG 26, TIG 150, TIG 200 TIG 26 Up/Down, TIG 150 Up/Down, TIG 200
Up/Down
4
3
2
1
TIG 150 Retox, TIG 200 Retox
Figure 4-1
Item Symbol Description 0
1 Gas nozzle
2 Grip plate
3 Torch cap
4 Operating elements

Commissioning
Connection variants
Item No.:099-011623-EWM01 9
4.2 Connection variants
3
2
1
4
2
Figure 4-2
Item Symbol Description 0
1 Welding torch decentral connection
2 Control lead cable plug
3 Gas connection
4 Welding torch central connection
5Commissioning
5.1 General
CAUTION
Risk of burns on the welding current connection!
If the welding current connections are not locked, connections and leads heat up and can
cause burns, if touched!
• Check the welding current connections every day and lock by turning in clockwise direction, if
necessary.
CAUTION
Hazards due to electrical current!
This equipment works using high electrical currents!
• Observe the safety instructions "For your safety" on the opening pages!
• Only connect connection or welding leads (e.g. electrode holders, welding torches, workpiece
lead, interfaces) when the equipment is switched off.
5.2 Area of application – proper usage
The welding machines are only suitable for:
• TIG welding
.

Commissioning
Equipping the torch
10 Item No.:099-011623-EWM01
5.3 Equipping the torch
5.3.1 TIG 17, 26
Equipping the torch using the example of the TIG 17 torch. Procedure is similar for other models
as appropriate.
AB
C
4
33
3
2
1
1
1
5
5
6
Figure 5-1
Item Symbol Description 0
1Gas nozzle
2 Collet casing
3 Torch body
4Collet
5 Electrode
6 Torch cap

Commissioning
Equipping the torch
Item No.:099-011623-EWM01 11
5.3.2 TIG 150, 200
Torches TIG 150 and TIG 200 can be fitted either with an electrode holder or gas diffuser. The
design of a gas diffuser means that it generates a laminar gas flow which is suitable for open air
welding in particular.
AB
C
6
6
7
4
4
3
2
1
1
1
5
Figure 5-2
Item Symbol Description 0
1 Torch body
2 Insulation
3 Gas diffuser
4 Electrode holder
5 Electrode
6 Gas nozzle
7 Torch cap

Functional characteristics
General
12 Item No.:099-011623-EWM01
6Functional characteristics
6.1 General
TIG welding torches are connected to the power source via the tube package. The following run via the
tube package:
• the welding current lead,
• the shielding gas supply and
• the control lead.
With liquid-cooled TIG welding torches, the lines for the
• coolant supply and
• coolant return
also run through the tube package.
The welding filler is generally added by hand in the form of rods during TIG welding. In fully automated
machines, the welding filler is fed in as wire via a separate feed unit.
6.2 TIG torch
TIG torches are equipped with a rocker switch. The rocker switch can be used to
• switch the main current on and off, and
• reduce the current to a secondary current during welding.
1
Figure 6-1
Item Symbol Description 0
1
Rocker

Functional characteristics
TIG Up/Down torch
Item No.:099-011623-EWM01 13
6.3 TIG Up/Down torch
TIG up/down torches are equipped with two rocker switches. The rocker switches can be used to
• switch the main current on and off,
• reduce to a secondary current by tapping,
• increase the welding current infinitely during the welding process (UP function) or
• infinitely reduce the current (DOWN function).
2
1
Figure 6-2
Item Symbol Description 0
1
Rocker switch
2
Rocker switch

Functional characteristics
TIG Retox torch
14 Item No.:099-011623-EWM01
6.4 TIG Retox torch
RETOX torches have two rocker switches in addition to a display. The assignment of the individual
operating elements with functions may differ from the welding machine being used.
In most cases,
• the left rocker switch can be used to switch the welding current on and off,
• the right rocker switch can be used to reduce the welding current infinitely (DOWN function) or
• increase it (UP function).
In addition to these functions, RETOX torches can also be used to call up JOBs made available by the
welding machine.
Depending on the function set on the welding machine, the display on a RETOX torch shows the
• welding current set or
• the JOB number selected.
3
2
1
Figure 6-3
Item Symbol Description 0
1
Rocker switch
2
Rocker switch
3 Display
More detailed information can be found in the relevant operating instructions for the power
source.

Maintenance and testing
Daily maintenance tasks
Item No.:099-011623-EWM01 15
7Maintenance and testing
CAUTION
The following work must always be carried out with the power source switched off.
7.1 Daily maintenance tasks
• Check torch, tube package and power connections for exterior damage and replace if available or
have repaired by specialist staff!
• Check that all gas and water connections are securely sealed.
• Check that the cooling equipment on the torch, and where applicable the power source cooling, is
functioning correctly.
• Check the coolant level. Top up deionised coolant if necessary.
• Check the replaceable parts in the torch, including the gas lens and gas nozzle seal.
• For torches with cold wire feed:
Check the cold wire supply nozzle and adjusting nut on the cold wire supply tube.
7.2 Monthly maintenance tasks
• Check for filter impurities in the coolant system.
If necessary, replace the filter insert; do not clean.
• Check the coolant container for sludge deposits and check the coolant for cloudiness.
Clean the coolant container if contaminated, and replace the coolant!
Observe the prescribed coolant quality on the cooling system!
• Check the electrical conductance of the coolant; replace the coolant if it is conductive.
• If the coolant is dirty, rinse through the torch alternately several times with fresh coolant using the
coolant return and supply.
• Disassemble, check and clean the plasma welding torch and the electrode clamping module.
Deposits in the torch can cause high frequency shocks and consequently cause damage to the torch.
• Check the O-rings in the clamping cap and in the collet casing, and in the gas and water nipples on
the torch.
Replace faulty O-rings. Grease new O-rings with silicone grease or Vaseline
7.3 Repair Work
CAUTION
Repairs may only be carried out by authorised specialist staff!
Do not remove the torch from the tube package!
Never clamp the torch body in a vice or similar, as this can cause the torch to be
irreparably destroyed!
If damage occurs to the torch or to the tube package which cannot be corrected as part of the
maintenance work, the entire torch must be returned to the manufacturer.
7.4 Disposing of equipment
This product has been manufactured from metallic materials and plastics. Almost all of the metal can be
re-used by separating it from the plastics. The identification of the plastics means that they can be sorted
and ultimately recycled.
The transport packaging has been reduced to the absolute essentials. The packaging materials have
been selected for maximum recyclability.

Operating problems, causes and remedies
Customer checklist
16 Item No.:099-011623-EWM01
8Operating problems, causes and remedies
All products are subject to rigorous production checks and final checks. If, despite this, something fails to
work at any time, please check the product using the following flowchart. If none of the fault rectification
procedures described leads to the correct functioning of the product, please inform your authorised
dealer.
8.1 Customer checklist
Error Cause Remedy
• Collet/gas nozzle not secured correctly.
• Power connections on torch side and
to workpiece are loose. • Check and tighten!
Torch gets too hot.
• Insufficient coolant flow. • Check cooling system!
• Control lead broken/faulty. • Check/repair!
No key function. • Flow monitor in circulation cooling unit
has been triggered. • Check coolant level and top up if necessary!
Arc between gas
nozzle and
workpiece.
• Spatter bridge between collet and gas
nozzle. • Clean inside of gas nozzle!
• Change the properties of the Tungsten
electrode which may occur with alloy
deposits due to contact with the
workpiece material or the filler material.
• Re-grind or replace the Tungsten
electrode.
Unstable arc.
• Incorrect welding parameters set. • Correct welding parameters!
• Significant spatter formation in the gas
nozzle. • Clean gas nozzle!
• Insufficient or missing gas cover. • Check gas cylinder contents and
pressure setting!
Pore formation.
• Draft is blowing away shielding gas. • Shield place of welding work using
safety walls!

Warranty
Customer checklist
Item No.:099-011623-EWM01 17
9Warranty
1-year warranty
Regardless of statutory warranty rightsand based on our General Terms and Conditions, EWM HIGHTEC
WELDING GmbH provides a 1-year warranty for its product starting from the date of purchase. Different
warranty periods apply to accessories and spare parts. Parts subject to wear are naturally exempt from
the warranty.
EWM guarantees the error-free condition of the products in terms of materials and processing. If the
product proves to be defective in terms of materials or processing within the warranty period, you have
the right to free repair or to replacement by an appropriate product, at our discretion. On receipt by EWM
the returned product becomes the property of EWM.
Condition
The prerequisite for providing the full warranty is operating the products in accordance with the EWM
operating instructions observing the relevant legal recommendations and guidelines. This is because only
machines that are maintained regularly function correctly in the long term.
Making a claim
When making a claim under the warranty, please contact only your authorised EWM sales partner.
Exclusion of warranty
The warranty does not apply to products that are damaged due to accidents, misuse, improper operation,
incorrect installation, use of force, disregard of the specifications and operating instructions, inadequate
maintenance (see chapter "Maintenance and Care"), exterior influences, acts of God or personal
misfortunes. Furthermore, it is not valid in the case of improper changes, repairs or modifications. In
addition, a claim for warranty does not exist in the case of partially or completely dismantled products and
interventions by persons who are not authorised by EWM, as well as in the case of normal wear.
Limitation
All claims regarding fulfilment or non-fulfilment on the part of EWM from this declaration in connection
with this product are limited as follows to the replacement of the actual damages. EWM's liability
stemming from this declaration in connection with this product is fundamentally limited to the amount that
the purchaser originally paid for the original purchase. This limitation does not apply to personal injuries
or damage to property caused by negligent behaviour on the part of EWM. In no way will EWM be
responsible for lost profits, indirect or subsequent damage. EWM is not liable for damages based on the
claims of third parties.
Place of jurisdiction
If the person making the claim is a business person, the sole place of jurisdiction for all disputes resulting
directly or indirectly from the contractual relationship shall be the headquarters or the branch office of the
supplier, at the discretion of the supplier. The purchaser gains ownership of the products supplied as
replacements within the framework of the warranty adjustment at the time of the exchange.

Replaceable parts
TIG 17
18 Item No.:099-011623-EWM01
10 Replaceable parts
10.1 TIG 17
Type Designation Item no.
TORCH CAP LONG Torch cap 094-001114-00000
TORCH CAP SHORT Torch cap 094-001120-00000
O-RING 9X1 O-ring 094-001313-00000
COLLET D0.5 L50.0 Collet 094-001308-00000
COLLET D1.0 L50.0 Collet 094-001309-00000
COLLET D1.2 L50.0 Collet 094-001310-00000
COLLET D1.6 L50.0 Collet 094-000931-00000
COLLET D2.0 L50.0 Collet 094-001311-00000
COLLET D2.4 L50.0 Collet 094-000932-00000
GASKET RING 17-18-26 Conical nipple 094-001306-00000
Insulation Insulator ring 094-001307-00000
Insulation Insulation, Teflon for large gas lens 094-001194-00000
COLLET BODY D0.5-1.2 Collet casing 094-001314-00000
COLLET BODY D1.6 Collet casing 094-000936-00000
COLLET BODY D2.0-2.4 Collet casing 094-000937-00000
COLLET BODY GASL D1.0 Collet casing 094-001324-00000
COLLET BODY GASL D1.6 Collet casing 094-001325-00000
COLLET BODY GASL D2.4 Collet casing 094-001192-00000
GASNOZZ4 D6.5 L47.0 Gas nozzle, ceramic 094-001316-00000
GASNOZZ5 D8.0 L47.0 Gas nozzle, ceramic 094-000926-00000
GASNOZZ6 D9.5 L47.0 Gas nozzle, ceramic 094-001317-00000
GASNOZZ7 D11.0 L47.0 Gas nozzle, ceramic 094-000927-00000
GASNOZZ8 D12.5 L47.0 Gas nozzle, ceramic 094-000929-00000
GASNOZZ10 D16.0 L47.0 Gas nozzle, ceramic 094-001318-00000
GASNOZZ12 D19.5 L47.0 Gas nozzle, ceramic 094-001319-00000
GASNOZZ4 GL D6.5 L42.0 Gas nozzle, ceramic 094-001320-00000
GASNOZZ5 GL D8.0 L42.0 Gas nozzle, ceramic 094-001321-00000
GASNOZZ6 GL D9.5 L42.0 Gas nozzle, ceramic 094-001322-00000
GASNOZZ7 GL D11.0 L42.0 Gas nozzle, ceramic 094-001195-00000
GASNOZZ8 GL D12.5 L42.0 Gas nozzle, ceramic 094-001196-00000

Replaceable parts
TIG 26
Item No.:099-011623-EWM01 19
10.2 TIG 26
Type Designation Item no.
TORCH CAP LONG Torch cap 094-001114-00000
TORCH CAP SHORT Torch cap 094-001120-00000
O-RING 9X1 O-ring 094-001313-00000
GASKET RING 17-18-26 Conical nipple 094-001306-00000
COLLET D0.5 L50.0 Collet 094-001308-00000
COLLET D1.0 L50.0 Collet 094-001309-00000
COLLET D1.2 L50.0 Collet 094-001310-00000
COLLET D1.6 L50.0 Collet 094-000931-00000
COLLET D2.0 L50.0 Collet 094-001311-00000
COLLET D2.4 L50.0 Collet 094-000932-00000
COLLET D3.2 L50.0 Collet 094-000935-00000
COLLET D4.0 L50.0 Collet 094-001312-00000
Insulation Insulator ring 094-001307-00000
Insulation Insulation, Teflon for large gas lens 094-001194-00000
COLLET BODY D0.5-1.2 Collet casing 094-001314-00000
COLLET BODY D1.6 Collet casing 094-000936-00000
COLLET BODY D2.0-2.4 Collet casing 094-000937-00000
COLLET BODY D3.2 Collet casing 094-000940-00000
COLLET BODY D4.0 Collet casing 094-001315-00000
COLLET BODY GASL D1.0 Collet casing 094-001324-00000
COLLET BODY GASL D1.6 Collet casing 094-001325-00000
COLLET BODY GASL D2.4 Collet casing 094-001192-00000
COLLET BODY GASL D3.2 Collet casing 094-001193-00000
COLLET BODY GASL D4.0 Collet casing 094-001326-00000
GASNOZZ4 D6.5 L47.0 Gas nozzle, ceramic 094-001316-00000
GASNOZZ5 D8.0 L47.0 Gas nozzle, ceramic 094-000926-00000
GASNOZZ6 D9.5 L47.0 Gas nozzle, ceramic 094-001317-00000
GASNOZZ7 D11.0 L47.0 Gas nozzle, ceramic 094-000927-00000
GASNOZZ8 D12.5 L47.0 Gas nozzle, ceramic 094-000929-00000
GASNOZZ10 D16.0 L47.0 Gas nozzle, ceramic 094-001318-00000
GASNOZZ12 D19.5 L47.0 Gas nozzle, ceramic 094-001319-00000
GASNOZZ4 GL D6.5 L42.0 Gas nozzle, ceramic 094-001320-00000
GASNOZZ5 GL D8.0 L42.0 Gas nozzle, ceramic 094-001321-00000
GASNOZZ6 GL D9.5 L42.0 Gas nozzle, ceramic 094-001322-00000
GASNOZZ7 GL D11.0 L42.0 Gas nozzle, ceramic 094-001195-00000
GASNOZZ8 GL D12.5 L42.0 Gas nozzle, ceramic 094-001196-00000
GASNOZZ12 GASL D19.5
L42.0 Gas nozzle, ceramic 094-001323-00000

Replaceable parts
TIG 150
20 Item No.:099-011623-EWM01
10.3 TIG 150
Type Designation Item no.
TIG 150/260W S Torch cap 094-011752-00000
TIG 150/260W M Torch cap 094-011753-00000
TIG 150/260W L Torch cap 094-011754-00000
WE-D1.6MM Gas lens 094-009658-00000
WE-D2.4MM Gas lens 094-009659-00000
WE-D3.2MM Gas lens 094-009660-00000
48MM NW12.5MM Gas nozzle, ceramic 094-009663-00000
48MM NW16.0MM Gas nozzle, ceramic 094-009664-00000
48MM NW19.5MM Gas nozzle, ceramic 094-009665-00000
TIG 150/260W S Torch cap 094-011752-00000
TIG 150/260W M Torch cap 094-011753-00000
TIG 150/260W L Torch cap 094-011754-00000
EH-D2.4MM TIG 150/260 W Electrode holder 094-011755-00000
D10, L26 , CERAMIC Gas nozzle, ceramic 094-011756-00000
36MM NW11.5MM TIG
150/260W Gas nozzle, ceramic 094-011757-00000
ISOLATION TIG 150/260W Adapter ring 094-011758-00000
TIG 150/260W Insulation for gas lens 094-011760-00000
TIG 150/260W Insulation 094-011979-00000
D11.5 L26 Ceramic gas nozzle 094-011980-00000
36MM NW10.0MM TIG
150/260W Ceramic gas nozzle 094-011982-00000
DIFF-D2.4MM Gas lens TIG 150/260W 094-011984-00000
EH-D1.6MM Electrode holder TIG 150/260 W 094-012406-00000
EH-D1.0MM Electrode holder, TIG, 150/260 W 094-012665-00000
EH-D2.0MM Electrode holder, TIG, 150/260 W 094-012666-00000
EH-D3.2MM Electrode holder, TIG, 150/260 W 094-012667-00000
DIFF-D1.0MM 150/260W Gas lens, TIG 094-012668-00000
DIFF-D1.6MM 150/260W Gas lens, TIG 094-012669-00000
DIFF-D2.0MM 150/260W Gas lens, TIG 094-012670-00000
DIFF-D3.2MM 150/260W Gas lens, TIG 094-012671-00000
36MM NW6.5MM 150/260W Ceramic gas nozzle, TIG 094-012673-00000
36MM NW8.0MM 150/260W Ceramic gas nozzle, TIG 094-012674-00000