EWM TIGSPEED OSCILLATION DRIVE 45 COLDWIRE User manual

Operating instructions
EN
Wire feed unit
tigSpeed continuous drive 45 coldwire
099-000237-EW501
Observe additional system documents!
25.04.2019

General instructions
WARNING
Read the operating instructions!
The operating instructions provide an introduction to the safe use of the products.
•Read and observe the operating instructions for all system components, especially the sa-
fety instructions and warning notices!
•Observe the accident prevention regulations and any regional regulations!
•The operating instructions must be kept at the location where the machine is operated.
•Safety and warning labels on the machine indicate any possible risks.
Keep these labels clean and legible at all times.
•The machine has been constructed to state-of-the-art standards in line with any applicable
regulations and industrial standards. Only trained personnel may operate, service and re-
pair the machine.
•Technical changes due to further development in machine technology may lead to a dif-
fering welding behaviour.
In the event of queries on installation, commissioning, operation or special conditions at the
installation site, or on usage, please contact your sales partner or our customer service
department on [phone].
A list of authorised sales partners can be found at www.ewm-group.com/en/specialist-dealers.
Liability relating to the operation of this equipment is restricted solely to the function of the equipment. No
other form of liability, regardless of type, shall be accepted. This exclusion of liability shall be deemed ac-
cepted by the user on commissioning the equipment.
The manufacturer is unable to monitor whether or not these instructions or the conditions and methods
are observed during installation, operation, usage and maintenance of the equipment.
An incorrectly performed installation can result in material damage and injure persons as a result. For this
reason, we do not accept any responsibility or liability for losses, damages or costs arising from incorrect
installation, improper operation or incorrect usage and maintenance or any actions connected to this in
any way.
© EWM AG
Dr. Günter-Henle-Strasse 8
56271 Mündersbach Germany
Tel.: [phone], Fax: -244
Email: [email protected]
www.ewm-group.com
The copyright to this document remains the property of the manufacturer.
Copying, including extracts, only permitted with written approval.
The content of this document has been prepared and reviewed with all reasonable care. The information
provided is subject to change; errors excepted.

Contents
Notes on the use of these operating instructions
099-000237-EW501
25.04.2019
3
1 Contents
1Contents..................................................................................................................................................3
2For your safety.......................................................................................................................................6
2.1 Notes on the use of these operating instructions ..........................................................................6
2.2 Explanation of icons.......................................................................................................................7
2.3 Part of the complete documentation..............................................................................................8
2.4 Safety instructions..........................................................................................................................9
2.5 Transport and installation ............................................................................................................13
3Intended use.........................................................................................................................................14
3.1 Use and operation solely with the following machines................................................................14
3.2 Applications..................................................................................................................................14
3.3 Documents which also apply.......................................................................................................15
3.3.1 Warranty.......................................................................................................................15
3.3.2 Declaration of Conformity.............................................................................................15
3.3.3 Service documents (spare parts and circuit diagrams)................................................15
3.3.4 Calibration/Validation ...................................................................................................15
4Machine description –quick overview ..............................................................................................16
4.1 Front view ....................................................................................................................................16
4.2 Rear view.....................................................................................................................................18
4.3Machine control –Operating elements........................................................................................20
4.3.1 Machine control –Concealed operating elements.......................................................22
4.3.2 Operating elements in the machine..............................................................................23
4.4 Connection plan...........................................................................................................................24
4.4.1 Legend..........................................................................................................................25
5Design and function.............................................................................................................................26
5.1 Transport and installation ............................................................................................................26
5.1.1 Protective flap, welding machine control......................................................................26
5.1.2 Ambient conditions.......................................................................................................27
5.1.2.1 In operation...................................................................................................27
5.1.2.2 Transport and storage...................................................................................27
5.1.3 Machine cooling............................................................................................................27
5.1.4 Workpiece lead, general...............................................................................................27
5.1.5 Notes on the installation of welding current leads........................................................28
5.1.6 Stray welding currents..................................................................................................29
5.1.7 Mains connection..........................................................................................................30
5.1.7.1 Mains configuration.......................................................................................30
5.1.8 Welding torch cooling system.......................................................................................30
5.1.8.1 Permitted torch coolant.................................................................................31
5.1.8.2 Maximal hose package length ......................................................................31
5.1.9 Intermediate hose package connection .......................................................................32
5.1.9.1 Intermediate hose package strain relief........................................................33
5.1.9.2 Locking the strain relief.................................................................................34
5.1.9.3 Control cable pin configuration .....................................................................34
5.1.10 Welding torch connection.............................................................................................35
5.1.10.1 Control cable pin configuration .....................................................................36
5.1.11 Wire feed......................................................................................................................37
5.1.11.1 Inserting the wire spool.................................................................................37
5.1.11.2 Changing the wire feed rollers......................................................................38
5.1.11.3 Inching the wire electrode.............................................................................38
5.1.11.4 Spool brake setting .......................................................................................39
5.1.12 Shielding gas supply (shielding gas cylinder for welding machine).............................40
5.1.12.1 Connecting the shielding gas supply ............................................................40
5.1.13 Shielding gas volume settings......................................................................................41
5.1.13.1 Gas test.........................................................................................................42
5.1.13.2 Purge hose package.....................................................................................42
5.1.14 Configuring the welding machine for mechanical arc fusion welding...........................42
5.1.15 Selection and adjustment.............................................................................................43
5.1.15.1 superPuls......................................................................................................44
5.1.16 Operating modes (functional sequences) ....................................................................45

Contents
Notes on the use of these operating instructions
4
099-000237-EW501
25.04.2019
5.1.16.1 Explanation of symbols .................................................................................45
5.1.16.2 Non-latched Manual......................................................................................46
5.1.16.3 Latched manual.............................................................................................47
5.1.16.4 Non-latched automatic ..................................................................................48
5.1.16.5 Latched automatic.........................................................................................49
5.1.16.6 Tack welding .................................................................................................50
5.2 Menus and sub-menus on the machine control...........................................................................51
5.2.1 Direct menus (direct access to parameters).................................................................51
5.2.2 Expert menu .................................................................................................................51
5.3 Access control..............................................................................................................................51
5.4 Welding torch holder....................................................................................................................52
6Maintenance, care and disposal.........................................................................................................53
6.1 General.........................................................................................................................................53
6.1.1 Cleaning........................................................................................................................53
6.1.2 Dirt filter.........................................................................................................................53
6.2 Maintenance work, intervals ........................................................................................................54
6.2.1 Daily maintenance tasks...............................................................................................54
6.2.2 Monthly maintenance tasks..........................................................................................54
6.2.3 Annual test (inspection and testing during operation)..................................................54
6.3 Disposing of equipment................................................................................................................55
7Rectifying faults....................................................................................................................................56
7.1 Checklist for rectifying faults........................................................................................................56
7.2 Error messages............................................................................................................................57
7.3 Resetting welding parameters to the factory settings..................................................................58
7.4 Vent coolant circuit.......................................................................................................................59
8Technical data.......................................................................................................................................60
8.1 tigSpeed continuous drive 45 coldwire ........................................................................................60
9Accessories ..........................................................................................................................................61
9.1 Options.........................................................................................................................................61
9.2 General accessories ....................................................................................................................61
10 Replaceable parts.................................................................................................................................62
10.1 Wire feed rollers...........................................................................................................................62
10.1.1 Wire feed rollers for steel wire......................................................................................62
10.1.1.1 Conversion kit................................................................................................62
10.1.2 Wire feed rollers for aluminium wire.............................................................................62
10.1.2.1 Conversion kit................................................................................................62
10.1.3 Wire feed rollers for cored wire.....................................................................................62
10.1.3.1 Conversion kit................................................................................................62
11 Appendix...............................................................................................................................................63
11.1 Setting instructions.......................................................................................................................63
11.1.1 Continuous TIG cold wire welding................................................................................64
11.1.2 superPuls TIG cold wire welding..................................................................................65
11.1.3 Continuous TIG cold wire welding................................................................................65
11.1.4 superPuls TIG cold wire welding..................................................................................66
11.2 Searching for a dealer..................................................................................................................67

Contents
Notes on the use of these operating instructions
099-000237-EW501
25.04.2019
5

For your safety
Notes on the use of these operating instructions
6
099-000237-EW501
25.04.2019
2 For your safety
2.1 Notes on the use of these operating instructions
DANGER
Working or operating procedures which must be closely observed to prevent imminent
serious and even fatal injuries.
•Safety notes include the "DANGER" keyword in the heading with a general warning symbol.
•The hazard is also highlighted using a symbol on the edge of the page.
WARNING
Working or operating procedures which must be closely observed to prevent serious
and even fatal injuries.
•Safety notes include the "WARNING" keyword in the heading with a general warning sym-
bol.
•The hazard is also highlighted using a symbol in the page margin.
CAUTION
Working or operating procedures which must be closely observed to prevent possible
minor personal injury.
•The safety information includes the "CAUTION" keyword in its heading with a general warn-
ing symbol.
•The risk is explained using a symbol on the edge of the page.
Technical aspects which the user must observe to avoid material or equipment damage.
Instructions and lists detailing step-by-step actions for given situations can be recognised via bullet
points, e.g.:
•Insert the welding current lead socket into the relevant socket and lock.

For your safety
Explanation of icons
099-000237-EW501
25.04.2019
7
2.2 Explanation of icons
Symbol
Description
Symbol
Description
Indicates technical aspects which the
user must observe.
Activate and release / Tap / Tip
Switch off machine
Release
Switch on machine
Press and hold
Switch
Incorrect / Invalid
Turn
Correct / Valid
Numerical value –adjustable
Input
Signal light lights up in green
Navigation
Signal light flashes green
Output
Signal light lights up in red
Time representation (e.g.: wait 4 s /
actuate)
Signal light flashes red
Interruption in the menu display (other
setting options possible)
Tool not required/do not use
Tool required/use

For your safety
Part of the complete documentation
8
099-000237-EW501
25.04.2019
2.3 Part of the complete documentation
These operating instructions are part of the complete documentation and valid only in
combination with all other parts of these instructions! Read and observe the operating
instructions for all system components, especially the safety instructions!
The illustration shows a general example of a welding system.
Figure 2-1
Item
Operating instructions
A.1
Wire feeder
A.2
Power source
A.3
Remote control
A.4
Control
A.5
Welding torch
A
Complete documentation

For your safety
Safety instructions
099-000237-EW501
25.04.2019
9
2.4 Safety instructions
WARNING
Risk of accidents due to non-compliance with the safety instructions!
Non-compliance with the safety instructions can be fatal!
•Carefully read the safety instructions in this manual!
•Observe the accident prevention regulations and any regional regulations!
•Inform persons in the working area that they must comply with the regulations!
Risk of injury from electrical voltage!
Voltages can cause potentially fatal electric shocks and burns on contact. Even low vol-
tages can cause a shock and lead to accidents.
•Never touch live components such as welding current sockets or stick, tungsten or wire
electrodes!
•Always place torches and electrode holders on an insulated surface!
•Wear the full personal protective equipment (depending on the application)!
•The machine may only be opened by qualified personnel!
•The device must not be used to defrost pipes!
Hazard when interconnecting multiple power sources!
If a number of power sources are to be connected in parallel or in series, only a techni-
cal specialist may interconnect the sources as per standard IEC 60974-9:2010: Installa-
tion and use and German Accident Prevention Regulation BVG D1 (formerly VBG 15) or
country-specific regulations.
Before commencing arc welding, a test must verify that the equipment cannot exceed
the maximum permitted open circuit voltage.
•Only qualified personnel may connect the machine.
•When taking individual power sources out of operation, all mains and welding current leads
must be safely disconnected from the welding system as a whole. (Hazard due to reverse
polarity voltage!)
•Do not interconnect welding machines with pole reversing switch (PWS series) or machines
for AC welding since a minor error in operation can cause the welding voltages to be com-
bined, which is not permitted.
Risk of injury due to improper clothing!
During arc welding, radiation, heat and voltage are sources of risk that cannot be
avoided. The user has to be equipped with the complete personal protective equipment
at all times. The protective equipment has to include:
•Respiratory protection against hazardous substances and mixtures (fumes and vapours);
otherwise implement suitable measures such as extraction facilities.
•Welding helmet with proper protection against ionizing radiation (IR and UV radiation) and
heat.
•Dry welding clothing (shoes, gloves and body protection) to protect against warm environ-
ments with conditions comparable to ambient temperatures of 100 °C or higher and arcing
and work on live components.
•Hearing protection against harming noise.
Risk of injury due to radiation or heat!
Arc radiation can lead to skin and eye injuries.
Contact with hot workpieces and sparks can lead to burns.
•Use hand shield or welding helmet with the appropriate safety level (depends on the appli-
cation).
•Wear dry protective clothing (e.g. hand shield, gloves, etc.) in accordance with
the applicable regulations of your country.
•Persons who are not directly involved should be protected with a welding curtain or suitable
safety screen against radiation and the risk of blinding!

For your safety
Safety instructions
10
099-000237-EW501
25.04.2019
WARNING
Explosion risk!
Apparently harmless substances in closed containers may generate excessive pressure
when heated.
•Move containers with inflammable or explosive liquids away from the working area!
•Never heat explosive liquids, dusts or gases by welding or cutting!
Fire hazard!
Due to the high temperatures, sparks, glowing parts and hot slag that occur during
welding, there is a risk of flames.
•Be watchful of potential sources of fire in the working area!
•Do not carry any easily inflammable objects, e.g. matches or lighters.
•Ensure suitable fire extinguishers are available in the working area!
•Thoroughly remove any residue of flammable materials from the workpiece prior to starting
to weld.
•Only further process workpieces after they have cooled down. Do not allow them to contact
any flammable materials!
CAUTION
Smoke and gases!
Smoke and gases can lead to breathing difficulties and poisoning. In addition, solvent
vapour (chlorinated hydrocarbon) may be converted into poisonous phosgene due to
the ultraviolet radiation of the arc!
•Ensure that there is sufficient fresh air!
•Keep solvent vapour away from the arc beam field!
•Wear suitable breathing apparatus if appropriate!
Noise exposure!
Noise exceeding 70 dBA can cause permanent hearing damage!
•Wear suitable ear protection!
•Persons located within the working area must wear suitable ear protection!

For your safety
Safety instructions
099-000237-EW501
25.04.2019
11
CAUTION
According to IEC 60974-10, welding machines are divided into two classes of
electromagnetic compatibility (the EMC class can be found in the Technical da-
ta) > see 8 chapter:
Class A machines are not intended for use in residential areas where the power supply comes
from the low-voltage public mains network. When ensuring the electromagnetic compatibility of
class A machines, difficulties can arise in these areas due to interference not only in the supply
lines but also in the form of radiated interference.
Class B machines fulfil the EMC requirements in industrial as well as residential areas, inclu-
ding residential areas connected to the low-voltage public mains network.
Setting up and operating
When operating arc welding systems, in some cases, electro-magnetic interference can occur
although all of the welding machines comply with the emission limits specified in the standard.
The user is responsible for any interference caused by welding.
In order to evaluate any possible problems with electromagnetic compatibility in the
surrounding area, the user must consider the following: (see also EN 60974-10 Appendix A)
•Mains, control, signal and telecommunication lines
•Radios and televisions
•Computers and other control systems
•Safety equipment
•The health of neighbouring persons, especially if they have a pacemaker or wear a hearing
aid
•Calibration and measuring equipment
•The immunity to interference of other equipment in the surrounding area
•The time of day at which the welding work must be carried out
Recommendations for reducing interference emission
•Mains connection, e.g. additional mains filter or shielding with a metal tube
•Maintenance of the arc welding system
•Welding leads should be as short as possible and run closely together along the ground
•Potential equalization
•Earthing of the workpiece. In cases where it is not possible to earth the workpiece directly,
it should be connected by means of suitable capacitors.
•Shielding from other equipment in the surrounding area or the entire welding system
Electromagnetic fields!
The power source may cause electrical or electromagnetic fields to be produced which
could affect the correct functioning of electronic equipment such as IT or CNC devices,
telecommunication lines, power cables, signal lines and pacemakers.
•Observe the maintenance instructions > see 6.2 chapter!
•Unwind welding leads completely!
•Shield devices or equipment sensitive to radiation accordingly!
•The correct functioning of pacemakers may be affected (obtain advice from a doctor if nec-
essary).
Obligations of the operator!
The respective national directives and laws must be complied with when operating the
machine!
•Implementation of national legislation relating to framework directive 89/391/EEC on the
introduction of measures to encourage improvements in the safety and health of workers at
work and associated individual guidelines.
•In particular, directive 89/655/EEC concerning the minimum safety and health requirements
for the use of work equipment by workers at work.
•The regulations applicable to occupational safety and accident prevention in the country
concerned.
•Setting up and operating the machine as per IEC 60974.-9.
•Brief the user on safety-conscious work practices on a regular basis.
•Regularly inspect the machine as per IEC 60974.-4.

For your safety
Safety instructions
12
099-000237-EW501
25.04.2019
The manufacturer's warranty becomes void if non-genuine parts are used!
•Only use system components and options (power sources, welding torches, electrode hold-
ers, remote controls, spare parts and replacement parts, etc.) from our range of products!
•Only insert and lock accessory components into the relevant connection socket when the ma-
chine is switched off.
Requirements for connection to the public mains network
High-performance machines can influence the mains quality by taking current from the mains
network. For some types of machines, connection restrictions or requirements relating to the
maximum possible line impedance or the necessary minimum supply capacity at the interface
with the public network (Point of Common Coupling, PCC) can therefore apply. In this respect,
attention is also drawn to the machines' technical data. In this case, it is the responsibility of the
operator, where necessary in consultation with the mains network operator, to ensure that the
machine can be connected.

For your safety
Transport and installation
099-000237-EW501
25.04.2019
13
2.5 Transport and installation
WARNING
Risk of injury due to improper handling of shielding gas cylinders!
Improper handling and insufficient securing of shielding gas cylinders can cause seri-
ous injuries!
•Observe the instructions from the gas manufacturer and any relevant regulations concern-
ing the use of compressed air!
•Do not attach any element to the shielding gas cylinder valve!
•Prevent the shielding gas cylinder from heating up.
CAUTION
Risk of accidents due to supply lines!
During transport, attached supply lines (mains leads, control cables, etc.) can cause
risks, e.g. by causing connected machines to tip over and injure persons!
•Disconnect all supply lines before transport!
Risk of tipping!
There is a risk of the machine tipping over and injuring persons or being damaged itself
during movement and set up. Tilt resistance is guaranteed up to an angle of 10° (ac-
cording to IEC 60974-1).
•Set up and transport the machine on level, solid ground.
•Secure add-on parts using suitable equipment.
Risk of accidents due to incorrectly installed leads!
Incorrectly installed leads (mains, control and welding leads or intermediate hose pack-
ages ) can present a tripping hazard.
•Lay the supply lines flat on the floor (avoid loops).
•Avoid laying the leads on passage ways.
Risk of injury from heated coolant and its connections!
The coolant used and its connection or connection points can heat up significantly
during operation (water-cooled version). When opening the coolant circuit, escaping
coolant may cause scalding.
•Open the coolant circuit only when the power source or cooling unit is switched off!
•Wear proper protective equipment (protective gloves)!
•Seal open connections of the hose leads with suitable plugs.
The units are designed for operation in an upright position!
Operation in non-permissible positions can cause equipment damage.
•Only transport and operate in an upright position!
Accessory components and the power source itself can be damaged by incorrect connection!
•Only insert and lock accessory components into the relevant connection socket when the ma-
chine is switched off.
•Comprehensive descriptions can be found in the operating instructions for the relevant ac-
cessory components.
•Accessory components are detected automatically after the power source is switched on.
Protective dust caps protect the connection sockets and therefore the machine against dirt and
damage.
•The protective dust cap must be fitted if there is no accessory component being operated on
that connection.
•The cap must be replaced if faulty or if lost!

Intended use
Use and operation solely with the following machines
14
099-000237-EW501
25.04.2019
3 Intended use
WARNING
Hazards due to improper usage!
The machine has been constructed to the state of the art and any regulations and
standards applicable for use in industry and trade. It may only be used for the welding
procedures indicated at the rating plate. Hazards may arise for persons, animals and
material objects if the equipment is not used correctly. No liability is accepted for any
damages arising from improper usage!
•The equipment must only be used in line with its designated purpose and by trained or
expert personnel!
•Do not improperly modify or convert the equipment!
3.1 Use and operation solely with the following machines
A suitable power source (system component) is required in order to operate the wire feed unit!
This machine can be combined with any TIG welding machine.
3.2 Applications
Wire feeder for integration in a welding system for TIG cold wire welding.

Intended use
Documents which also apply
099-000237-EW501
25.04.2019
15
3.3 Documents which also apply
3.3.1 Warranty
For more information refer to the "Warranty registration" brochure supplied and our information regarding
warranty, maintenance and testing at www.ewm-group.com!
3.3.2 Declaration of Conformity
The labelled product complies with the following EC directives in terms of its design and
construction:
•Low Voltage Directive (LVD)
•Electromagnetic Compatibility Directive (EMC)
•Restriction of Hazardous Substance (RoHS)
In case of unauthorised changes, improper repairs, non-compliance with specified deadlines for "Arc
Welding Equipment –Inspection and Testing during Operation," and/or prohibited modifications which
have not been explicitly authorised by the manufacturer, this declaration shall be voided. An original
document of the specific declaration of conformity is included with every product.
3.3.3 Service documents (spare parts and circuit diagrams)
WARNING
Do not carry out any unauthorised repairs or modifications!
To avoid injury and equipment damage, the unit must only be repaired or modified by
specialist, skilled persons!
The warranty becomes null and void in the event of unauthorised interference.
•Appoint only skilled persons for repair work (trained service personnel)!
Original copies of the circuit diagrams are enclosed with the unit.
Spare parts can be obtained from the relevant authorised dealer.
3.3.4 Calibration/Validation
We hereby confirm that this product was tested with calibrated measuring equipment according to the ap-
plicable standards IEC/EN 60974, ISO/EN 17662, EN 50504 and complies with the permissible tole-
rances. Recommended calibration interval: 12 months.

Machine description –quick overview
Front view
16
099-000237-EW501
25.04.2019
4 Machine description – quick overview
4.1 Front view
Figure 4-1

Machine description –quick overview
Front view
099-000237-EW501
25.04.2019
17
Item
Symbol
Description 0
1
Transport bar
2
Carrying handle
3
Protective cap
Cover for the wire feed mechanismand other operating elements.
Depending on the machine series, additional stickers with information on the replace-
ment parts and JOB lists will be located on the inside.
4
Wire spool inspection window
Check wire supply
5
Slide latch, lock for the protective cap
6
Machine feet
7
Torch holder
8
Protective cap > see 5.1.1 chapter
9
Key switch for protection against unauthorised use > see 5.3 chapter
1----------changes possible,G front drive-4x-EX
0----------changes not possible.
10
Machine control > see 4.3 chapter
11
Quick connect coupling (red)
coolant return
12
Quick connect coupling (blue)
coolant supply
13
Cooling air outlet
14
Quick connect coupling
Shielding gas
15
Connection socket (TIG)
Welding current, minus potential
16
Connection socket (12-pole)
Welding torch control lead
17
Wire electrode connection
Welding torch wire feed

Machine description –quick overview
Rear view
18
099-000237-EW501
25.04.2019
4.2 Rear view
Figure 4-2

Machine description –quick overview
Machine control –Operating elements
099-000237-EW501
25.04.2019
19
Item
Symbol
Description 0
1
Connector plug, 5-pole
Control lead
2
Machine fuse (6,3 A)
3
Main switch, machine on/off
4
Connector plug (TIG)
Welding current, minus potential
5
Connecting nipple G¼, shielding gas connection
6
Mains connection cable > see 5.1.7 chapter
7
Cooling air inlet
8
External wire feed inlet
Pre-cut casing inlet for external wire feed.
9
Quick connect coupling (red)
coolant return
10
Quick connect coupling (blue)
coolant supply

Machine description –quick overview
Machine control –Operating elements
20
099-000237-EW501
25.04.2019
4.3 Machine control –Operating elements
Unnamed operating elements have no function in this machine configuration!
Figure 4-3