Extech Instruments prc20 User manual

USER GUIDE
Thermocouple Calibrator
Model PRC20
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

2PRC20-EU-EN-V1.2 1/13
Introduction
Thank you for selecting the Extech Model PRC20. This device is shipped fully tested and calibrated
and, with proper use, will provide years of reliable service. Please visit the Extech Instruments
website (www.extech.com) to check for the latest version of this User Guide. Extech Instruments is
an ISO-9001 certified company.
Safety
International Safety Symbols
This symbol, adjacent to another symbol or terminal, indicates the user must refer to the
manual for further information.
This symbol, adjacent to a terminal, indicates that, under normal use, hazardous voltages
may be present
Double insulation
Safety Notes
Turn the unit OFF when the device is not in use.
Remove the batteries if the device is to be stored for longer than 60 days.
Never dispose of batteries in a fire. Batteries may explode or leak.
Never mix battery types. Always install new batteries of the same type.
Cautions
Improper use of this meter can cause damage, shock, injury or death. Read and understand
this user manual before operating the meter.
Inspect the condition of the thermocouples and the meter itself for any damage before
operating the meter. Repair or replace any damage before use.
If the equipment is used in a manner not specified by the manufacturer, the protection provided
by the equipment may be impaired.
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

3PRC20-EU-EN-V1.2 1/13
Meter Description
1. AC adaptor input jack
2. Display
3. Power ON/OFF
4. Source output adjustment arrow buttons
5. Set and exit the adjustment mode button
6. Unit button (thermocouple type, °F or °C)
7. I/O button
8. MEM (memory STEP button)
9. Backlight/ZERO button
10. Thermocouple mini-connector
Display Layout
1. SOURCE mode icon
2. ZERO function status icon
3. Thermocouple type
4. MEASURE mode icon
5. Auto Power OFF active icon
6. Battery status icon
7. Measure mode value
8. Measure mode units icon
9. Datalogger memory location
10. Source mode value
11. Source mode units icon
12. Cold Junction Compensation (CJC) circuit status (ON or OFF)
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

4PRC20-EU-EN-V1.2 1/13
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

5PRC20-EU-EN-V1.2 1/13
Keypad Descriptions and Operation
POWER BUTTON and AUTO POWER OFF FEATURE
1. Use the POWER button to turn the unit ON or OFF. When the unit is powered up, a short
self-test will ensue after which the display will stabilize.
2. When the battery symbol flashes on the display, replace the battery as soon as possible.
Low battery power may cause inaccurate readings and erratic meter operation.
3. This instrument is equipped with Auto Power OFF which turns the meter off after 10 minutes
of inactivity. To override this feature; press and hold the POWER button until the display
icon “ATP” turns off.
UNIT BUTTON
Momentarily press the UNIT button to select °F or °C units.
TYPE BUTTON
Press and Hold the TYPE/UNIT button for 1 second to change the thermocouple type (J, K, T, E, C,
R, S, N or mV).
I/O BUTTON
Momentarily press the I/O button to select either SOURCE (output) or MEASURE (input).
CJC ON/OFF
Simultaneously press the IO and MEM buttons to turn the CJC (cold junction compensation) on or
off. The CJC icon will indicate the status.
Note: CJC should normally be ON.
(Backlight) BUTTON
Momentarily press the Backlight button to turn the backlight on or off.
ZERO ( ) BUTTON
In the MEASURE or SOURCE mode, Press and Hold the ZERO ( ) button for 1 second to zero
the meter.
OFFSET ADJUSTMENT
The offset adjustment can be used to correct any known linearity errors with the thermocouple.
1. Select the measure mode and a thermocouple type (J/K/T/E/C/R/S/N).
2. Press and Hold the SET button for 1 second to enter the offset adjust mode.
3. Press the ▲or ▼button to change the offset value.
4. Press and Hold the SET button for 1 second to zero the offset value.
5. Momentarily press the SET button to save the change and exit the function.
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

6PRC20-EU-EN-V1.2 1/13
►◄▼and ▲BUTTONS
The arrow buttons are used to set the output value in the SOURCE mode.
1. Select the SOURCE mode
2. Press the ►or ◄button select a digit for adjustment. The blinking underline curser
identifies the digit selected.
3. Press the ▼or ▲button to adjust the value of the digit. Press and Hold the ▼or ▲button to
rapidly adjust the value.
SET BUTTON
The SET button is used to manually step through the 5 stored output values.
1. Select the SOURCE mode
2. Momentarily press the SET button and the value stored in memory location 01 will be
sourced. “MEM.01” appears in the display.
3. Each press of the SET button will step through the 5 memory locations.
4. The arrow buttons can be used to adjust the value in each memory location.
STEP/MEM BUTTON
The STEP/MEM button is used to automatically step through the 5 stored output values. The meter
can be set for a single cycle of the stored values or a continuous cycle.
1. Select the SOURCE mode
2. Press and Hold the STEP/MEM button. ”STEPSS” (single cycle) and “STEPSC” (continuous
cycle) will alternately appear in the display. Release the button when the desired mode is
displayed.
3. In single cycle mode the meter will source the current or voltage displayed in MEM01 for 5
seconds. The meter will then advance to MEM02 for 5 seconds. This will continue through
MEM05 and then step down through the memory locations. The cycle will end when MEM01
has been reached.
4. In the continuous mode the cycle will continue until manually stopped.
5. Momentarily press the MEM button to stop the cycle. “END” will briefly appear in the display.
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

7PRC20-EU-EN-V1.2 1/13
STORING VALUES INTO MEMORY
There are 5 memory locations for each thermocouple type and for mV. The default values stored in
the these locations are:
Memory
Location
Type
J, K, C, R, S, N
Type
T
Type
E
mV
M1 0.0oC
(32.0oF)
0.0oC
(32.0oF)
0.0oC
(32.0oF)
0mV
M2 100.0oC
(212.0oF)
100.0oC
(212.0oF)
100.0oC
(212.0oF)
10.00mV
M3 500.0oC
(932.0oF)
200.0oC
(392.0oF)
200.0oC
(392.0oF)
25.00mV
M4 750.0oC
(1382.0oF)
300.0oC
(572.0oF),
500.0oC
(932.0oF)
40.00mV
M5 1000.0oC
(1832.0oF)
400.0oC
(752.0oF)
750.0oC
(1382.0oF)
50.00mV
To change the values in memory:
1. Select the SOURCE mode
2. Press the SET button to select the memory location to be changed.
3. Press the arrow buttons to adjust to the new value
4. Momentarily press the MEM button to store the value. The memory location icon will blink
while the value is being stored..
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

8PRC20-EU-EN-V1.2 1/13
Modes of Operation
MEASURE (Input) Mode of Operation
1. Turn the meter ON.
2. “MEASURE” will appear in the display.
3. Momentarily press the UNIT button to select °F or °C.
4. Press and Hold the UNIT button for 1 second to change the thermocouple type (or mV).
5. Connect the thermocouple to the meter.
6. Read the measurement on the display.
Note: See the keypad description section to turn CJC on/off.
SOURCE (Output) Mode of Operation
In this mode, the unit can source the equivalent mV value for the temperature and the
thermocouple type selected. The values can be output either manually or stepped from memory
as described earlier.
1. Turn the meter ON
2. MEASURE” will appear in the display.
3. Momentarily press the UNIT button to select °F or °C.
4. Press and Hold the UNIT button for 1 second to change the thermocouple type (or mV).
5. Press the “I/O” button to select SOURCE.
6. Connect the Calibration Cable from the meter to the device to be calibrated.
7. Use the
arrow buttons to set the desired output value in the lower display. The upper
display indicates the actual temperature or voltage value being sourced. If the upper display
does not match the set value, check the batteries or the connections to the device being
calibrated.
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

9PRC20-EU-EN-V1.2 1/13
Tilt Stand / Hanger
The rear stand is provides two methods for convenience in viewing.
1. Pull the bottom portion of the stand out to place the unit on a flat surface for viewing.
2. Pull the bottom and top portions of the stand out, and then rotate the stand to allow the unit
to be hung.
Battery Replacement
When the battery icon appears on the display, the six AA batteries must be replaced.
The battery compartment is located on the rear of the meter.
1. Open the tilt stand, loosen the captive Philips head screw and remove the battery cover.
2. Remove and replace the batteries, observing polarity.
3. Replace and secure the battery cover.
All EU users are legally bound by the Battery Ordinance to return all used batteries to
community collection points or wherever batteries / accumulators are sold.
Disposal in household trash or refuse is prohibited.
Disposal: Follow the valid legal stipulations in respect of the disposal of the device at the
end of its lifecycle
Battery Safety Reminders
Please dispose of batteries responsibly; always observe local, state, and federal regulations
with regard to battery disposal.
Never dispose of batteries in a fire. Batteries may explode or leak.
Never mix battery types or old and new batteries. Always install new batteries of the same
type.
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

10 PRC20-EU-EN-V1.2 1/13
Specifications
General Specifications
Display Dot matrix LCD
Cold junction compensation 0.02°F per °F (0.03°C per °C)
Thermocouple Standard and Scale NIST 175, ITS-90
Meter Power 6 AA batteries or AC adaptor
Auto Power OFF Meter automatically powers off after 10 minutes of inactivity
Operating Temperature 5ºC to 40ºC (41ºF to 104ºF)
Storage Temperature -20ºC to 60ºC (- 4ºF to 140ºF)
Operating Humidity Max 80% up to 87ºF (31ºC) decreasing linearly to 50% at
104ºF (40ºC)
Storage Humidity <80%
Operating Altitude 2000 meters (7000ft) maximum
Dimensions 159 x 80 x 44 mm (6.3 x 3.2 x 1.7")
Weight 225g (8 oz.) without batteries
Range Specifications
Source and Measure Ranges Resolution Accuracy (% of reading)
Type J -58 to 1832°F (-50 to 1000°C)
Type K -58 to 2498°F (-50 to 1370°C)
Type T -184 to 752°F (-120 to 400°C)
Type E -58 to 1382°F (-50 to 750°C)
Type C 32 to 3182°F (0 to 1750°C)
Type R 32 to 3182°F (0 to 1750°C)
Type S 32 to 3182°F (0 to 1750°C)
Type N -58 to 2372°F (-50 to 1300°C)
0.1° (measure)
1° (source)
± (0.05% + 1°C /1.8°F)
mV Measure: -10mV to 60mV
Source: -5mV to 55mV 0.01mV ± (0.01% + 1digit)
Copyright ©2013 FLIR Systems, Inc.
All rights reserved including the right of reproduction in whole or in part in any form
www.extech.com
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]