Extreme Networks AP-8533 Owner's manual

Published July 2017
9035171
AP-8533 Access Point
Regulatory Guide - CDRDB

AP-8533 Regulatory Guide
Extreme Networks Inc. 1
Extreme Confidential Restricted
1.Regulatory Information
This device is approved under Extreme Networks Inc.
This guide applies to Model Number: CDRDB
All Extreme devices are designed to be compliant with the rules and regulations in the locations they are sold and will be
labeled as required.
Local language translations are available at the following website:
http://www.extremenetworks.com/support/documentation/.
Any changes or modifications to Extreme equipment not expressly approved by Extreme Networks could void the user’s
authority to operate the equipment.
Extreme devices are professionally installed — the Radio Frequency Output Power will not exceed the maximum allowable
limit for the country of operation.
Antennas: Use only the supplied or an approved replacement antenna. Unauthorized antennas, modifications, or
attachments could cause damage and may violate regulations.
This device is only to be used with an Extreme Wireless Switch.
For use only with Extreme approved and UL Listed mobile computers, Extreme approved, and UL Listed/Recognized
battery packs.

AP-8533 Regulatory Guide
Extreme Networks Inc. 2
Extreme Confidential Restricted
2. Wireless Device Country Approvals
NOTE
This section is only applicable to WW/WR/EU configurations.
NOTE
Regulatory markings subject to certification are applied to the device signifying the
radio(s) is/are approved for use in the following countries and continents: United
States, Canada, Japan, China, South Korea, Australia, and Europe.
Please refer to the Declaration of Conformity (DoC) for details of other country markings. This is available at:
http://www.extremenetworks.com/support/documentation/.
NOTE
Europe includes Austria, Belgium, Bulgaria, Croatia, Czech Republic, Cyprus, Denmark,
Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Liechtenstein, Lithuania, Luxembourg, Malta, Nether-lands, Norway, Poland, Portugal,
Romania, Slovak Republic, Slovenia, Spain, Sweden, Switzerland, and the United
Kingdom.
CAUTION
Operation of the device without regulatory approval is illegal.
Country Selection
Select only the country in which the device will be used. Any other selection will make the operation of this device illegal.
Country Roaming
This device incorporates the International Roaming feature (IEEE802.11d), which will ensure the product operates on the
correct channels for the particular country of use.

AP-8533 Regulatory Guide
Extreme Networks Inc. 3
Extreme Confidential Restricted
Frequency of Operation – IC
5 GHz Only:
The use in the UNII (Unlicensed National Information Infrastructure) band 1 (5150-5250 MHz) is restricted to Indoor Use
Only; any other use will make the operation of this device illegal.
Industry Canada Statement:
CAUTION
The device for the band 5150-5250 MHz is only for indoor usage to reduce potential for
harmful interference to co-Channel mobile satellite systems. High power radars are
allocated as primary users (meaning they have priori-ty) of 5250-5350 MHz and 5650-
5850 MHz and these radars could cause interference and/or damage to LE-LAN devices.
Avertissement
Le dispositive fonctionnant dans la bande 5150-5250 MHz est réservé uniquement pour
une utilisation à l'intérieur afin de réduire les risques de brouillage préjudiciable aux
systèmes de satellites mobiles utilisant les mêmes canaux. Les utilisateurs de radars de
haute puissance sont désignés utilisateurs principaux (c.-à-d., qu'ils ont la priorité) pour
les bands 5250-5350 MHz et 5650-5850 MHz et que ces radars pourraient causer du
brouillage et/ou des dommages aux dispositifs LAN-EL.
2.4 GHz Only:
The available channels for 802.11 b/g operation in the US are Channels 1 to 11. The range of channels is limited by firmware.
Warnings for Use of Wireless Devices
CAUTION
Please observe all warning notices with regard to the usage of wireless devices.

AP-8533 Regulatory Guide
Extreme Networks Inc. 4
Extreme Confidential Restricted
Potentially Hazardous Atmospheres – Fixed Installations
You are reminded of the need to observe restrictions on the use of radio devices in fuel depots, chemical plants etc. and
areas where the air contains chemicals or particles such as grain, dust, or metal powders.
Safety in Aircraft
Switch off your wireless device whenever you are instructed to do so by airport or airline staff. If your device offers a ‘flight
mode’ or similar feature, consult airline staff as to its use in flight.
Safety in Hospitals
Wireless devices transmit radio frequency energy and may affect medical electrical equipement.
Wireless devices should be switched off wherever you are requested to do so in hospitals, clinics, or healthcare facilitlies.
These requests are designed to prevent possible interference with sensitive medical equipement.
Wireless devices transmit radio frequency energy and may affect medical electrical equipment. When installed adjacent to
other equipment, it is advised to verify that the adjacent equipment is not adversely affected.
Pacemakers
Pacemaker manufacturers recommended that a minimum of 15cm (6 inches) be maintained between a handheld wireless
device and a pacemaker to avoid potential interference with the pacemaker. These recommendations are consistent with
independent research and recommendations by Wireless Technology Research.
Persons with Pacemakers:
•Should ALWAYS keep the device more than 15cm (6 inches) from their pacemaker when turned ON.
•Should not carry the device in a breast pocket.
•Should use the ear furthest from the pacemaker to minimise the potential for interference.
•If you have any reason to suspect that interference is taking place, turn OFF your device.
Other Medical Devices
Please consult your physician or the manufacturer of the medical device to determine if the operation of your wireless
product may interfere with the medical device.

AP-8533 Regulatory Guide
Extreme Networks Inc. 5
Extreme Confidential Restricted
RF Exposure Guidelines
Safety Information
•Reducing RF Exposure – Use Properly
Only operate the device in accordance with the instructions supplied.
•International
The device complies with internationally recognized standards covering human exposure to electromagnetic
fields from radio devices. For information on ‘International’ human exposure to electromagnet fields, refer to the
Extreme Declaration of Conformity (DoC) at http://www.extremenetworks.com/support/documentation/.
US and Canada
•Co-located statement
To comply with FCC RF exposure compliance requirement, the antenna used for this transmitter must not be co-
located or operating in conjunction with any other transmitter/antenna except those already approved in this
filling.
To satisfy US and Canadian RF exposure requirements, a transmitting device must operate with
a minimum separation distance of XX cm or more from a person’s body. The minimum
separation distance 35 cm must match the distance established in the SAR Test report.
Pour satisfaire aux exigences Américaines et Canadiennes d'exposition aux radio fréquences, un
dispositif de transmission doit fonctionner avec une distance de séparation minimale de XX cm
ou plus de corps d'une personne.
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 35 cm between the radiator and your body.
NOTE IMPORTANTE: (Pour l'utilisation de dispositifs mobiles)
Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un non
contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 35 cm de distance entre la source de
rayonnement et votre corps.
oRemote and Standalone Antenna Configurations
To comply with FCC RF exposure requirements, antennas that are mounted externally at remote locations or
operating near users at stand-alone desktop of similar configurations must operate with a minimum
separation distance of 35 cm from all persons.
To comply with FCC Antenna requirements, the Antenna must be adjust such that the RF emission lobes are
below 30 degrees elevation.

AP-8533 Regulatory Guide
Extreme Networks Inc. 6
Extreme Confidential Restricted
3. Radio Frequency Interference
Requirements- FCC
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
Note: This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15
of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
Radio Transmitters (Part 15)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any interference received including interference that
may cause undesired operation. When the radio is configured for outdoor operation, EIRP will be limited to below 21dBm
based on the antenna gain and elevation gain entered. The software automatically restricts the output power to the
certified levels when the professional installer selects the approved antenna that is being used.

AP-8533 Regulatory Guide
Extreme Networks Inc. 7
Extreme Confidential Restricted
Maximum conducted
power(dBm)
Antenna
Gain(dBi)
Maximum EIRP
power(dBm)
2.4GHz
26.28
4.4
30.68
5GHz UNII-1 / indoor
22.79
5.9
28.69
5GHz UNII-1 / outdoor
16.88
5.9
22.78
5GHz UNII-1 / outdoor
Above 30 degree
16.88
4.1
20.98
5GHz UNII-2A
21.91
5.9
27.81
5GHz UNII-2C
22.41
5.9
28.31
5GHz UNII-3
22.84
5.9
28.74

AP-8533 Regulatory Guide
Extreme Networks Inc. 8
Extreme Confidential Restricted
4. Radio Frequency Interference
Requirements- Canada
CAN ICES-3 (B)/NMB-3(B)
Radio Transmitters
For RLAN Devices:
The use of 5 GHz RLAN’s, for use in Canada, have the following restrictions:
•Restricted Band 5.60 – 5.65 GHz
This device is in compliance with the NRC for Industry Canada applicable to license-exempt radios. Use is
allowed with the following two conditions: (1) the device must not produce interference, and (2) the the device
must accept any interference to the radio even if the interference is likely to compromise operation.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de
licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de
brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radio électrique subi même si le
brouillage est susceptible d'en compromettre le fonctionnement.
Label Marking: The Term ‘IC:’ before the radio certification only signifies that Industry Canada technical specifications
were met.
In accordance with the regulations of Industry Canada, this radio transmitter can operate with an antenna of a
type and a maximum gain (or lower) approved for the transmitter by Industry Canada. With the aim of
reducing the risk of radio interference to other users, the chosen antenna type and it gain should be selected so
that the equivalent isotropically radiated power (e.i.r.p.) does not exceed the intensity necessary for the
establishment of a satisfactory connection.
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une
antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le
but de réduire les risques de brouillage radio électrique à l'intention des autres utilisateurs, il faut choisir le type
d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas
l'intensité nécessaire à l'établissement d'une communication satisfaisante.
This radio transmitter (CDRDB) has been approved by Industry Canada to operate with the antenna types
listed below and having a maximum gain allowable and the impedance required for each type of antenna. The
antenna types not included in this list, or whose gain is higher than the maximum gain indicates, are strictly
prohibited for the operation of the transmitter.

AP-8533 Regulatory Guide
Extreme Networks Inc. 9
Extreme Confidential Restricted
The antenna list and types are included in the following tables:
Part Number Antenna Type
2.4
GHZ
Gain
(dBi)
5
GHZ
Gain
(dBi) Elevation Gain
Impedance
(Ohms)
ML-2452-HPAG4A6-01
Dipole
4
7.3
5.7
50
ML-2452-APAG2A1-01
Dipole
2.7
1.7
N/A
50
ML-2452-HPA6-01
Dipole
5.3
6.1
4.09
50
ML-2452-APA2-01
Dipole
3.17
4.85
N/A
50
ML-2452-PNA5-01R
Panel
5.5
6
5.2
50
ML-2452-SEC5M4-N36
Polarized
Panel
6.92
7.23
3.95
50
ML-2452-PTA4M4-036
Patch
5
6.6
N/A
50
ML-2499-HPA6H-01
Polarized
Dipole
5.4
N/A
N/A
50
ML-5299-HPA5H-01
Polarized
Dipole
N/A
5
-1.21
50
Le présent émetteur radio (identifier le dispositif par son numéro de certification ou son numérode modèle s'il
fait partie du matériel de catégorie I) a été approuvé par Industrie Canada pour fonctionner avec les types
d'antenne énumérés ci-dessous et ayant un gain admissible maximal et l'impédance requise pour chaque type
d'antenne. Les types d'antenne non inclus dans cette liste ou dont le gain est supérieur au gain maximal
indiqué, sont strictement interdits pour l'exploitation de l'émetteur.
Statement of Compliance
Extreme Networks hereby declares that this device is in compliance with the essential requirements and other relevant
provisions of Directive 1999/5/EC and 2011/65/EU. A Declaration of Conformity may be obtained from
http://www.extremenetworks.com/support/documentation/.

AP-8533 Regulatory Guide
Extreme Networks Inc. 10
Extreme Confidential Restricted
This module is intended for OEM integrator. The OEM integrator is still responsible for the IC compliance requirement of
the end product, which integrates this module.
User’s manual of the end product
In the user’s manual of the end product, the end user has to be informed to keep at least 40 cm separation with the
antenna while this end product is installed and operated. The end user has to be informed that the IC radio-frequency
exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any
changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this
equipment. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Label of the end product
The final end product must be labeled in a visible area with the following " Contains IC: 4141B-CDRDB ".
The Host Model Number (HMN) must be indicated at any location on the exterior of the end product or product
packaging or product literature which shall be available with the end product or online.

AP-8533 Regulatory Guide
Extreme Networks Inc. 11
Extreme Confidential Restricted
5. Waste Electrical and Electronic
Equipment (WEEE)
Waste Electrical and Electronic Equipment
In accordance with Directive 2012/19/EU of the European Parliament on waste electrical and electronic equipment
(WEEE):
1. The symbol above indicates that separate collection of electrical and electronic equipment is required.
2. When this product has reached the end of its serviceable life, it cannot be disposed of as unsorted municipal
waste. It must be collected and treated separately.
3. It has been determined by the European Parliament that there are potential negative effects on the environment
and human health as a result of the presence of hazardous substances in electrical and electronic equipment.
4. It is the users’ responsibility to utilize the available collection system to ensure WEEE is properly treated. For
information about the available collection system, please contact Extreme Customer Support at [phone]
(Ireland).
Korea Warning Statement for Class B ITE
기종별사용자안내문
B급기기
(가정용 방송통신기자재)
이기기는 가정용(B급) 전자파적합기기로서 주로
가정에서 사용하는 것을 목적으로 하며, 모든
지역에서 사용할 수있습니다.
South Korea
For a radio equipment using 2400~2483.5MHz or 5725~5825MHz, the following two expression should be displayed;
해당 무선설비는 운용 중전파혼신 가능성이 있음
해당 무선설비는 전파혼신 가능성이 있으므로 인명안전과 관련된 서비스는 할수없습니다
Taiwan
臺灣
低功率電波輻射性電機管理辦法
第十二條

AP-8533 Regulatory Guide
Extreme Networks Inc. 12
Extreme Confidential Restricted
經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功
能。
第十四條
低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使
用。
前項合法通信，指依電信規定作業之無線電通信。
低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。
無線接入點 (專業安裝)
•本公司於說明書中提供所有必要資訊以指導使用者/安裝者正確的安裝及操作」警語。
並於該中文使用說明書及器材上標示
•本器材須經專業工程人員安裝及設定，始得設置使用，且不得直接販售給一般消費者」
警語。
電磁波曝露量MPE標準值1mW/cm²；本產品使用時建議應距離人體 35 cm