Extreme Networks ExtremeMobility AP410i/e User manual

ExtremeMobility™Access
Points AP410i/e
Installation Guide
9036459-00 RevAA
Published November 2019

Copyright © 2019 Extreme Networks, Inc. All rights reserved.
Legal Notice
Extreme Networks, Inc. reserves the right to make changes in specifications and other information
contained in this document and its website without prior notice. The reader should in all cases
consult representatives of Extreme Networks to determine whether any such changes have been
made.
The hardware, firmware, software or any specifications described or referred to in this document
are subject to change without notice.
Trademarks
Extreme Networks and the Extreme Networks logo are trademarks or registered trademarks of
Extreme Networks, Inc. in the United States and/or other countries.
All other names (including any product names) mentioned in this document are the property of
their respective owners and may be trademarks or registered trademarks of their respective
companies/owners.
For additional information on Extreme Networks trademarks, please see:
www.extremenetworks.com/company/legal/trademarks
Open Source Declarations
Some software files have been licensed under certain open source or third-party licenses. End-
user license agreements and open source declarations can be found at:
www.extremenetworks.com/support/policies/software-licensing

Table of Contents
Preface................................................................................................................................................................................................ 4
Conventions.............................................................................................................................................................................4
Providing Feedback to Us.................................................................................................................................................5
Getting Help.............................................................................................................................................................................5
Documentation and Training...........................................................................................................................................6
Related Publications............................................................................................................................................................ 6
Purchase Order Information............................................................................................................................................ 7
Chapter 1: Product Overview....................................................................................................8
AP410i/e Features................................................................................................................................................................ 8
AP410i/e Power Source..................................................................................................................................................... 9
LED Indicators........................................................................................................................................................................ 9
Chapter 2: Install the Access Point........................................................................................ 10
AP410i/e Box Contents....................................................................................................................................................10
Access Point Installation Options and Accessories Information................................................................... 11
Install the Access Point on a Drywall or Wood Wall or to a Solid Flat Ceiling...................................... 12
Install the Access Point on a Suspended or Drop Ceiling with a Flat T-bar........................................... 17
Install the Access Point on a Junction Box or Gang Box................................................................................22
Install the Access Point on a Beam............................................................................................................................23
Chapter 3: Antenna Configuration for External Antenna Model Access Point...............26
Chapter 4: Access Points Specifications.............................................................................. 28
Chapter 5: Regulatory Information....................................................................................... 29
Safety Guidelines................................................................................................................................................................29
MPE Statement for Mobile Devices........................................................................................................................... 29
Federal Communications Commission (FCC) Notice.......................................................................................29
Industry Canada Notice.................................................................................................................................................. 30
Detachable Antenna Usage............................................................................................................................................31
Australia Notice................................................................................................................................................................... 32
Brazil Anatel Statement...................................................................................................................................................32
Hazardous Substances.....................................................................................................................................................32
Supplement to Product Instructions.........................................................................................................................33
NCC Statement....................................................................................................................................................................33
CE Information.....................................................................................................................................................................33
European Waste Electrical and Electronic Equipment (WEEE) Notice..................................................34
Declaration of Conformity in Languages of the European Community..................................................35
Index.......................................................................................................................................... 38
ExtremeMobility™ Access Points AP410i/e 3

Preface
This section discusses the conventions used in this guide, ways to provide feedback, additional help, and
other Extreme Networks®publications.
Conventions
This section discusses the conventions used in this guide.
Text Conventions
The following tables list text conventions that are used throughout this guide.
Table 1: Notice Icons
Icon Notice Type Alerts you to...
General Notice Helpful tips and notices for using the product.
Note Important features or instructions.
Caution Risk of personal injury, system damage, or loss of data.
Warning Risk of severe personal injury.
New! New Content Displayed next to new content. This is searchable text within the PDF.
Table 2: Text Conventions
Convention Description
Screen displays This typeface indicates command syntax, or represents information as it appears on the
screen.
The words enter and
type
When you see the word “enter” in this guide, you must type something, and then press
the Return or Enter key. Do not press the Return or Enter key when an instruction
simply says “type.”
[Key] names Key names are written with brackets, such as [Return] or [Esc]. If you must press two
or more keys simultaneously, the key names are linked with a plus sign (+). Example:
Press [Ctrl]+[Alt]+[Del]
Words in italicized type Italics emphasize a point or denote new terms at the place where they are defined in
the text. Italics are also used when referring to publication titles.
ExtremeMobility™ Access Points AP410i/e 4

Providing Feedback to Us
Quality is our first concern at Extreme Networks, and we have made every eort to ensure the accuracy
and completeness of this document. We are always striving to improve our documentation and help
you work better, so we want to hear from you! We welcome all feedback but especially want to know
about:
•Content errors or confusing or conflicting information.
•Ideas for improvements to our documentation so you can find the information you need faster.
•Broken links or usability issues.
If you would like to provide feedback to the Extreme Networks Information Development team, you can
do so in two ways:
•Use our short online feedback form at https://www.extremenetworks.com/documentation-
feedback/.
•Email us at [e-mail].
Please provide the publication title, part number, and as much detail as possible, including the topic
heading and page number if applicable, as well as your suggestions for improvement.
Getting Help
If you require assistance, contact Extreme Networks using one of the following methods:
Extreme
Portal
Search the GTAC (Global Technical Assistance Center) knowledge base, manage support cases
and service contracts, download software, and obtain product licensing, training, and
certifications.
The Hub A forum for Extreme Networks customers to connect with one another, answer questions, and
share ideas and feedback. This community is monitored by Extreme Networks employees, but is
not intended to replace specific guidance from GTAC.
Call GTAC For immediate support: 1-800-998-2408 (toll-free in U.S. and Canada) or [phone]. For
the support phone number in your country, visit: www.extremenetworks.com/support/contact
Before contacting Extreme Networks for technical support, have the following information ready:
•Your Extreme Networks service contract number and/or serial numbers for all involved Extreme
Networks products
•A description of the failure
•A description of any action(s) already taken to resolve the problem
•A description of your network environment (such as layout, cable type, other relevant environmental
information)
•Network load at the time of trouble (if known)
•The device history (for example, if you have returned the device before, or if this is a recurring
problem)
•Any related RMA (Return Material Authorization) numbers
Subscribing to Service Notifications
You can subscribe to email notifications for product and software release announcements, Vulnerability
Notices, and Service Notifications.
ExtremeMobility™ Access Points AP410i/e 5

1 Go to www.extremenetworks.com/support/service-notification-form.
2 Complete the form with your information (all fields are required).
3 Select the products for which you would like to receive notifications.
Note
You can modify your product selections or unsubscribe at any time.
4 Click Submit.
Documentation and Training
To find Extreme Networks product guides, visit our documentation pages at:
Current Product Documentation www.extremenetworks.com/documentation/
Archived Documentation (for earlier
versions and legacy products)
www.extremenetworks.com/support/documentation-archives/
Release Notes www.extremenetworks.com/support/release-notes
Hardware/Software Compatibility Matrices https://www.extremenetworks.com/support/compatibility-matrices/
White papers, data sheets, case studies,
and other product resources
https://www.extremenetworks.com/resources/
Training
Extreme Networks oers product training courses, both online and in person, as well as specialized
certifications. For more information, visit www.extremenetworks.com/education/.
Related Publications
ExtremeWireless™, ExtremeWireless WiNG™, and ExtremeMobility™documentation can be found on the
Extreme Networks Documentation Site.
Extreme recommends the following guides for users of ExtremeWireless™products:
•ExtremeWireless AP3916ic Installation Guide
•ExtremeWireless AP3912i Installation Guide
•ExtremeWireless AP3965i & AP3965e Installation Guide
•ExtremeWireless AP3935i & AP3935e Installation Guide
•ExtremeWireless AP3825i & AP3825e Installation Guide
•ExtremeWireless AP3805i FCC/ROW Installation Guide
•ExtremeWireless AP3801i Quick Reference Guide
•C5210 Quick Reference
•C5110 Quick Reference
•C4110 Quick Reference
•C25 Quick Reference
•C35 Quick Reference
•ExtremeWireless CLI Reference Guide
•ExtremeWireless End User License Agreements
ExtremeMobility™ Access Points AP410i/e 6

•ExtremeWireless External Antenna Site Preparation and Installation Guide
•ExtremeWireless External Antenna with Wave 2 Site Preparation and Installation Guide
•ExtremeWireless Getting Started Guide
•ExtremeWireless Integration Guide
•ExtremeWireless Maintenance Guide
•ExtremeWireless Open Source Declaration
•ExtremeWireless User Guide
•IdentiFi Wireless WS-AP3865e Installation Guide
•IdentiFi Wireless WS-AP3825i & WS-AP3825e Installation Guide
•IdentiFi Wireless WS-AP3805i & WS-AP3805e Installation Guide
Purchase Order Information
Table 3: Brackets purchase order information
Part number Description
37201 Main mounting bracket for indoor access points (included in the access point box), along
with the 50 mm M3 security screw pack for main mounting bracket
30518 WS-MBI-DCMTR01 bracket
30516 WS-MBI-WALL04 bracket
37211 WS-MBI-DCFLUSH bracket
Table 4: Bracket accessories purchase order information
Part number Description
KT-135628-01 Universal mounting kit for wireless LAN (WLAN) access points
37210 Flat metal easy-attach adapter for main mounting bracket
BRKT-000147A-01 Beam clip accessory
30525; WS-CAB-RJ45-FLT01 RJ45 flat cable accessory for ceiling mount brackets
Table 5: Power supply purchase order information
Part number Description
37219 PWR 12V DC, 3A, 2.5 mm X 5.5 mm connector
ExtremeMobility™ Access Points AP410i/e 7

1Product Overview
AP410i/e Features
AP410i/e Power Source
LED Indicators
The AP410i/e access points are indoor model 802.11ax access points. The “i” in AP410i indicates that the
access point comes with internal antennas and the “e” indicates that it comes with external antenna
connectors. The access points feature built-in dual-band radios, two band-locked radios, eight WiFi
internal or external antennas, and one Bluetooth Low Energy (BLE) antenna.
The AP410i/e is mounted on a flat surface such as a wall, a solid flat ceiling, and to a junction or gang
box, and can be installed on a suspended or drop ceiling.
Note
The AP410i/e requires a minimum base firmware of WiNG 7.3.0.
In this document, the access points are addressed as AP410i/e when the product features and
installation procedures are the same for both access points.
AP410i/e Features
The AP410i/e access points have the following features:
•Radios: Three 802.11ax radios
•One 2X2 2.4 GHz radio
•One 4X4 5 GHz radio
•One 2X2 2.4 GHz and 5 GHz radio
•One 2.4 GHz IoT radio
•Console port: RJ45
•Two Ethernet ports:
•1 x 10/100/1000 Mbps auto-negotiation Ethernet port, RJ45
•One multi-rate GE/2.5 GE Ethernet port
•LEDs: Seven – all LEDs will be powered on during reset and will connect to general purpose input/
output (GPIO) pins
•One reset button
•One Kensington lock
•One safety hanger provision
•One USB 2.0 type A connector
•Power: PoE 802.3at and 802.3bt (see AP410i/e Power Source for details)
•Antennas:
ExtremeMobility™ Access Points AP410i/e 8

•AP410i: Eight WiFi internal antennas and one BLE internal antenna
•AP410e: Six RP-SMA external antenna ports and one BLE RP-SMA antenna
•Temperature:
•AP410i: 0°C to +50°C (32°F to +122°F) @ 6000 ft.
•AP410e: -20°C to +55°C (-4°F to +131°F) @ 6000 ft.
•Enclosure: Plastic with metal base
AP410i/e Power Source
Power source Description
Power over Ethernet (PoE) Power is provided through the 2.5 GE multi-rate
Ethernet ports of AP410i/e, compliant to be powered
with 802.3at and 802.3bt to provide full functionality.
For reduced functionality, use 802.3af.
External 12V DC optional power supply Power is provided through an external DC power supply
plugged into an AC source. A GPIO connection is
required to indicate that an external 12V DC power
supply is present.
LED Indicators
The LED indicators are located on the front face of the access point but are not visibly marked.
Table 6: AP410i/e LED indicators
LED indicator LED color Description
Status Green Normal operational status
Amber Non-operational status
GE1 Ethernet Amber 100 Mbps
Green 1000 Mbps
Purple 2.5G
GE2 Ethernet Amber 100 Mbps
Green 1000 Mbps
Radio 1 Green 2.4G activity
Radio 2 Amber 5G activity
Radio 3 White Sensor activity
IoT radio (BLE) Blue Indicates BLE is enabled
Product Overview
ExtremeMobility™ Access Points AP410i/e 9

2Install the Access Point
AP410i/e Box Contents
Access Point Installation Options and Accessories Information
Install the Access Point on a Drywall or Wood Wall or to a Solid Flat Ceiling
Install the Access Point on a Suspended or Drop Ceiling with a Flat T-bar
Install the Access Point on a Junction Box or Gang Box
Install the Access Point on a Beam
The access point is installed on flat surfaces such as drywall or wood wall, solid flat ceiling, suspended
or drop ceiling with T-bar, to beams, or to a junction or gang box. Optional adapters and brackets are
available for mounting the access point to non-flat ceiling tiles and T-bars.
See purchase order information for details on access points and optional brackets part numbers.
Before installing the access point:
1 Verify the box contents.
2 Visually inspect the access point, the bracket, and any other optional accessories you have ordered
for physical damage.
Contact Extreme Networks Support if there is any damage.
3 Read and review the safety guidelines.
AP410i/e Box Contents
When you purchase the AP410i or AP410e access point, ensure that the following items are available in
the box:
•An AP410i/e Quick Reference
•One access point (AP410i or AP410e)
•A stainless-steel mounting bracket for 802.11ax indoor access point
•Two Phillips pan head wood screws
•Two screw-in anchors
Quantity Item
1
1
1
ExtremeMobility™ Access Points AP410i/e 10

Quantity Item
2
2
Note
All optional brackets and accessories are sold separately.
Access Point Installation Options and Accessories Information
The access point comes with the main mounting bracket (#37201; mounting bracket for 802.11ax indoor
access points). There are various optional brackets, bracket adapters, and accessories that can be
purchased separately.
Table 7: Brackets and accessories usage for various installation options
Mounting
bracket or
accessory
Wall
install
Solid
flat
ceiling
install
Ceiling
install
(T-bar)
Ceiling
install
(protrude
d T-bar)
Juncti
on box
install
Beam
install
Ceiling tile
protrusion
T-bar
widths
Notes
37201; main
mounting
bracket
Yes Yes Yes Yes, by
adding
the
optional
T-bar
adapter
to the
main
mounting
bracket
No Yes, by
adding
the beam
clip
accessory
to the
main
mounting
bracket
No 15/16 in. This bracket is
shipped with
the access
point.
Installation
methods: Wall
mount or flush
ceiling mount
with single
width.
KT-135628-0
1 accessory;
used with
main
mounting
bracket
No No Yes Yes No No Yes 15/16 in. Wall mount or
protruded
ceiling mount
with single
width.
30518 WS-
MBI-
DCMTR01
bracket
No No Yes Yes No No Yes 9/16 in.,
3/2 in.,
15/16 in.
Protruded
ceiling mount
with varying
widths.
30516 WS-
MBI-
WALL04
bracket
Yes No No No Yes No No No Wall mount
with single
width. Junction
box installation.
Install the Access Point
ExtremeMobility™ Access Points AP410i/e 11

Table 7: Brackets and accessories usage for various installation options (continued)
Mounting
bracket or
accessory
Wall
install
Solid
flat
ceiling
install
Ceiling
install
(T-bar)
Ceiling
install
(protrude
d T-bar)
Juncti
on box
install
Beam
install
Ceiling tile
protrusion
T-bar
widths
Notes
37210 flat
metal easy-
attach
adapter;
used with
main
mounting
bracket
Yes Yes No No No No No N/A Wall mount,
ceiling mount,
or install on any
solid surface.
37211 WS-
MBI-
DCFLUSH
bracket
No No Yes Yes No No Yes 9/16 in.,
3/2 in.,
15/16 in.
Protruded
ceiling mount
with varying
widths.
BRKT-00014
7A-01; beam
clip
accessory
No No No No No Yes No N/A The beam clip is
attached to the
main mounting
bracket.
30525 WS-
CAB-RJ45-
FLT01
accessory;
used with
any ceiling
bracket
No Yes Yes No No No No N/A This accessory
can be used
only with
ceiling mount
brackets listed
in this table.
Install the Access Point on a Drywall or Wood Wall or to a Solid
Flat Ceiling
The access point is installed on a drywall or wood wall or to a solid flat ceiling using:
•#37201, stainless-steel main mounting bracket that ships with the unit
•#30516, WS-MBI-WALL04 bracket, two Phillips pan-head screws, and screw-in anchors
Note
The WALL04 bracket and screw-in anchors are used only for drywall or wood wall
mounting.
•#37201, stainless-steel main mounting bracket with #37210, flat metal easy-attach adapter
•Phillips pan head screws
Tip
The best practice is to install the access point using the mounting brackets.
Install the Access Point
ExtremeMobility™ Access Points AP410i/e 12

Install the Access Point Using the Main Mounting Bracket
The main mounting bracket is a stainless-steel bracket that ships with the access point. It is used during
drywall or wood wall installation, or solid flat ceiling installation.
Tip
The best practice is to use the main mounting bracket for all wall installations.
1 Using the mounting bracket as a template, mark and drill two hole centers on the wall.
Note
The bracket feet must be pointing up.
Figure 1: Main mounting bracket
Install the Access Point
ExtremeMobility™ Access Points AP410i/e 13

Callout Description
1 Main mounting bracket mounting holes
2 Main mounting bracket feet
2 Insert the Phillips pan head screws into the main mounting bracket holes and attach the bracket to
the wall.
Use screw-in anchors, if needed.
3 Connect the Ethernet cable RJ45 connector into the GE1 port.
4 Place the access point onto the bracket feet and slide it down to lock it in place.
Install a Security Torx Locking Screw
The security torx locking screw is used to prevent the access point from being removed from the main
mounting bracket (#37201). There are two security lock screw holes on the rear of the access point.
Follow this procedure to install the security torx locking screw using one of the security lock holes on
the access point.
Note
Perform this task after the access point is attached to the main mounting bracket on a drywall
or wood wall.
1 Line up the security torx locking screw using the rear guides on the access point.
2 Tighten the security torx locking screw using a T8 bit screwdriver.
3 Turn the locking screw into the security screw hole until the security torx locking screw passes
through to the other side and touches the screw stop feature.
Figure 2: Security torx locking screw stop feature
Install the Access Point
ExtremeMobility™ Access Points AP410i/e 14

Callout Description
1 Security torx locking screw stop feature
Note
You cannot remove the access point from the main mounting bracket until the security
torx locking screw is removed.
Install the Access Point Using the WALL04 Bracket
The optional WALL04 (#30516) bracket is used for wall installations and ships with two Phillips pan
head screws and two screw-in anchors. You must purchase the bracket separately.
1 Using the WALL04 bracket as a template, mark and drill two holes on a wall.
The WALL04 bracket has "A" and "B" hole templates. The best practice is to use this template to
mark the attachment holes.
Note
When using the "A" or "B" hole template, if the holes are not near the corners of the
bracket, you can break o the corner to minimize the amount of bracket that is visible
behind the access point.
Note
The locking tab on the WS-MBI-WALL04 bracket must be on the top side during
installation.
2 Attach the WS-MBI-WALL04 bracket on a wall using two Phillips pan head screws.
Attach the screw-in anchors before attaching the pan head screws for extra
3 Connect the GE1 cable to the access point.
4 Insert the access point into the WALL04 bracket keyhole posts and slide it into place.
5 Lock the access point at approximately 1/4" from the bracket.
Install the Access Point Using the Main Mounting Bracket and Easy-Attach
Adapter
Use the flat metal easy-attach adapter (#37210) in combination with the main mounting bracket
(#37201) when you do not want to use the screw holes on the main mounting bracket. The easy-attach
adapter extends past the access point housing, thereby making it convenient to easily attach and
remove the access point from a flat surface.
Install the Access Point
ExtremeMobility™ Access Points AP410i/e 15

1 Keep the adapter to the center of the main mounting bracket, push and rotate it.
Figure 3: Flat metal easy-attach adapter being attached to the main mounting
bracket
2 Using the attachment holes on the easy-attach adapter, mark and drill two hole centers on a wall or
a solid flat ceiling.
3 Attach the easy-attach adapter to the wall using two Phillips pan-head screws.
Use screw-in anchors, if needed.
4 Connect the Ethernet cable RJ45 connector into the GE1 port.
Install the Access Point
ExtremeMobility™ Access Points AP410i/e 16

5 Place the access point onto the bracket feet and slide it down to lock it in place.
Note
The bracket feet must be pointing up.
Install the Access Point Directly on a Wall
If you do not want to use the main mounting bracket that ships with the access point, you can install the
access point directly on a wall using two phillips pan head screws.
Tip
The best practice is to use the main mounting bracket for wall installations.
1 Measure and drill two holes 104 mm (4.100 in.) apart from each other on the wall.
2 Insert the Phillips pan head screws into the mounting holes on the wall.
Use screw-in anchors, if needed.
Note
Leave 1/8” gap between the screw head and the wall.
3 Connect the Ethernet cable RJ45 into the GE1 port.
4 Align the access point against the screw heads and slide it down.
Ensure that the access point is secured in place. If the access point is loose, unmount it and decrease
the distance between the two screw heads. Then, remount the access point.
Install the Access Point on a Suspended or Drop Ceiling with a
Flat T-bar
For suspended or drop ceiling install, the main mounting bracket is used directly on the T-bar. If there is
a ceiling tile protrusion, the optional T-bar adapter is attached to the main mounting bracket prior to T-
bar installation.
The access point is mounted to a suspended or a drop ceiling using:
•#37201, stainless-steel main mounting bracket to a flat T-bar
•#37201, stainless-steel main mounting bracket with KT-135628-01 adapter to a flat T-bar
•#37211, WS-MBI-DCFLUSH bracket to a flat T-bar
•#30518, WS-MBI-DCMTR01 bracket to a T-bar
Install the Access Point on a Flat T-bar Using Main Mounting Bracket
Ensure that the T-bar meets the following conditions before installing the main mounting bracket on a
flat T-bar:
•T-bar width must be 15/16 in. (24 mm).
•T-bar bottom must be flat, all the way across the ceiling.
•T-bar must be structurally sound.
Install the Access Point
ExtremeMobility™ Access Points AP410i/e 17

•T-bar maximum base thickness must not exceed 0.055 in. (1.4 mm).
•Ceiling tile over the T-bar must be flat, all the way across.
The main mounting bracket is used on a T-bar when the ceiling model is a suspended or drop ceiling
and when there is a T-bar on the ceiling.
1 Remove the ceiling tiles.
2 Push and rotate the main mounting bracket on the T-bar in such a way that the center angled
locking tabs of the main bracket gets attached to the T-bar.
Figure 4: Install the main mounting bracket on a T-bar
3 Place the access point on the bracket feet and slide it down to lock it in place.
Hold the access point and rock it back and forth to ensure that it is securely mounted.
4 Replace the ceiling tiles.
5 Attach the RJ45 connector to the GE1 port.
Install the Access Point
ExtremeMobility™ Access Points AP410i/e 18

Install the Access Point on a Flat T-bar Using Main Mounting Bracket and
KT-135628-01 Adapter
Ensure that the T-bar meets the following conditions before installing the main mounting bracket with
the KT-135628-01 adapter on a T-bar:
•T-bar width can be either 9/16 in. (15 mm) or 15/16 in. (24 mm).
•T-bar bottom must be flat all the way across.
•T-bar must be structurally sound.
•T-bar maximum base thickness must not exceed 0.055 in. (1.4 mm).
Due to manufacturing variation, some adapters can accommodate up to 0.060 in. (1.5 mm)
•Ceiling tile may protrude up to 0.35 in. (8.89 mm) below the T-bar
If the ceiling tile is not flat and has a protrusion, use the main mounting bracket with the KT-135628-01
adapter. Attach the adapter to the main mounting bracket before attaching the bracket to a T-bar.
1 Attach the T-bar adapter to the main mounting bracket by lining up the small bends on the adapter
with the long raised parts on the main bracket.
2 Pull up the KT-135628-01 adapter locking pin, and twist.
Ensure that the locking pin goes into the locking pin hole on the main bracket and locks in place.
Figure 5: Attach the KT-135628-01 adapter on the main mounting bracket
Install the Access Point
ExtremeMobility™ Access Points AP410i/e 19

Callout Description
A KT-135628-01 adapter
B KT-135628-01 T-bar holder
C KT-135628-01 adapter locking pin
3 Slide the KT-135628-01 T-bar holder onto the T-bar and replace the tiles to hold the adapter onto the
T-bar.
4 Hold and rock the access point back and forth to ensure that it is securely mounted.
5 Attach the RJ45 connector to the GE1 port.
Install the Access Point on a Flat T-bar Using the DCFLUSH bracket
Ensure that the T-bar meets the following conditions before installing the DCFLUSH bracket on it:
•T-bar width must be 9/1 in. (15mm), 15/16 in. (24mm), or 1.5 in. (38 mm).
•T-bar bottom must be flat all the way across.
•T-bar must be structurally sound.
•T-bar maximum base thickness must not exceed 0.080 in. (2 mm).
•Ceiling tile must be flat all the way across.
•Maximum ceiling tile protrusion allowed is 0.015 in. (0.380 mm).
The WS-MBI-DCFLUSH (#37211) bracket is used on a flat T-bar when you do not want to use the main
mounting bracket on it.
1 Remove the ceiling panels around the T-bar.
2 Open the movable sliding part of the DCFLUSH bracket to give the stationary and slider T-bar more
space.
Figure 6: DCFLUSH bracket parts and T-bar
Install the Access Point
ExtremeMobility™ Access Points AP410i/e 20