FAAC FCI4300 User manual

Cellular Intercom 3G
FAAC International Inc.
Headquarter & East Coast Operations
3160 Murrell Rd
Rockledge, FL 32955
Tel. [phone]
www.faacusa.com
FAAC International Inc.
West Coast Operations
357 South Acacia Avenue
Fullerton, CA 92831
DO NOT GIVE TO HOME OWNER.
FOR PROFESSIONAL USE ONLY
3G

2
TABLE OF CONTENTS
Really important things you need to know
A look around the product
Overview of inside
Pedestal Installation
Power Module in detail
Cellular module in detail
Wiring relays
Keypad/prox module in detail
Connecting slave devices
Inserting the SIM
Powering up and LEDS
Installing the programmer APP for the first time
Programming a brand new install
Programming an existing install
Programming main steps
Additional Features
Keypad codes
Prox cards (optional models only)
Auto opening/closing
App control of gates
Do not disturb
After hours calling
Programming codes
Ringing times
Volumes
Information
Relay times
Complete list of parameters
Troubleshooting
3
4
4
5
6
6
7
7
8
8
9
9
11
11
12
15
16
17
20
21
21
22
22
23
23
24
25
25
28

3
Really Important things you Need to Know..
Please read this entire manual before
installing this product.
To be installed by certified and qualified
personnel / gate automation dealer only. Not
for DIY install!
Ensure there is good At&T 3G or T-Mobile
2G/3G signal at the gate/door of the install
site BEFORE installing this product.
Set up on a bench in workshop BEFORE
going to site. Program the unit in the comfort
of your work bench and call technical support
should you have questions.
Manufacturer warranty does NOT cover
lighting / storm damage. You MUST fit
external surge protection and lightning rod in
order to maintain warranty on this product.
Evidence of surge protection will be requested
on generation of RGA numbers.
3
6
1
2
4

4
Now lets have a look around the product…
Overview of Inside…
Call button
Push button
Speaker grill
Cellular PCB
Optional
Prox Coil
Optional
Keypad
module
Optional Keypad
Optional
Prox reader
module
Surge &
Power
Conditionin
g Module
Hinged front
door
Microphone
Built in antenna
Security screw
access
Optional
Prox badge
reader

5
Pedestal Installation
!
!
3
Use minimum 16 gauge wire
from the 24v dc adaptor
provided to the terminals
shown.
1
After fitting the box to the
gooseneck, re-fit the module
and connect a 14 gauge
earth wire to the earth
terminal.
2
Earth Rod
(close as
possible)
Maintain manufacturer’s
warranty by adhering to the
guidelines shown. Use 110v
surge protected supply.
Surge protected 110v
4
24v dc PSU
16 gauge
MIN
30 feet MAX
Call box
Remove 4 screws
and remove power
conditioning module
(if needed)

6
Relay 2
24vdc out
-
+
+
-
+
-
Solar or 12v DC IN
24vdc IN (Do NOT use 12v here)
500mA quick blow
output fuse
Optional Battery
Connection leads
3Ah 12v dc max
Power
Module
in
Detail…
Earth Rod
Connection
Gate Position Limit
switch
(optional)
1A quick blow
input fuse
Exit Button
To Call Button
(pre-wired)
12v dc 100mA
(button illumination)
24v dc IN
(pre-wired)
CPU Status
Signal Status
Power
Cellular
Module in
Detail…
SIM holder
Antenna
connection
Relay 1
N/O
COM
N/C
N/O
COM
N/C

7
1
2
Slave IN connections
Slave IN
Slave OUT
3
Optional
PROX
module
Baud jumper (remove
for older intercoms)
Keypad
Module
Keypad /
PROX
Modules in
Detail…
Slave OUT connections
Wiring
Relays
Electric Gates
24v out
GND
Note: The manufacturer is not
responsible for wiring to third
party devices. Please consult
an experienced security
installer.
Pedestrian
gates or door
Magnetic
lock
Exit button
Separate lock Power
supply (not supplied)
Start
Common
COM
N/O
N/C
COM

8
1 2 3 24v OUT
IN
OUT
IN OUT
IN
1 2 3 24v OUT
IN
1 2 3 24v
1 2 3 24v
Inserting the SIM card
WARNING
Ensure power is OFF. Do not hot
insert or remove while power on.
To next
device
Optional
Keypad
Optional
Prox
reader
Optional Slave
Keypad
Optional Slave
Prox Reader
CAT5 (30ft max)
300ft if device
powered separately
To next
device
45 chamfer OUT
Pads DOWN
Ensure SIM is activated.
Pre-pay SIM will need credit first.
At&T preferred. T-Mobile also
compatible in certain areas.
Connecting
Slave
Devices

9
Powering Up & LEDs
Perform a final check of wiring and ensure the antenna is connected before switching on the
power. Once the power is switched on, the power LED should illuminate.
Installing the Programmer APP for the first time
If you are using an Apple or Android smart phone, download and install the FAAC Cell Access
Pro APP. It will make programming much easier.
Note: You may notice the app “Cell Access” on the store. This is for homeowners to use.
CPU
Flashing = standby
Constant ON/OFF = busy
SIGNAL STRENGTH
1 flash = poor (1 bar)
2 flashes = low (2 bars)
3 flashes = good (3 bars)
4 flashes = Strong (4 bars)
5 flashes = searching
POWER

10
Accept and allow all
permissions (Android
version shown)
After you send the
registration email, go
back to the app
screen.
To register first time,
enter your name, email
and cell phone
number.