Factoryfurniture Murton Manual

factoryfurniture.co.uk
Murton Table
OPERATION & MAINTENANCE MANUAL

factoryfurniture.co.uk
Introduction
Design
Design, shop drawings and development by
Factory Furniture Ltd.
Manufacture
Factory Furniture manufactured components. Products
are assembled in Factory workshops, checked and
dispatched ready for installation. Replacement products
or components thereof should be ordered direct from
Factory Furniture Ltd.
Copyright
The design copyright for the product and drawing
copyright remains the sole property of Factory Furniture
Ltd.
General Specifications
Table
Metric length 2020mm | width 825mm | height 720mm
Imperial length 6’ 7½” | width 2’ 8½” | height 2’ 4½”
Approx Weight 158kg
Fixing Centres 1920mm (6’ 3½”) x 600mm (1’ 11½”)
Picnic Table
Metric length 2020mm | width 1650mm | height
720mm
Imperial length 6’ 7½” | width 5’ 5” | height 2’ 4½”
Approx Weight 241kg
Fixing Centres 1920mm (6’ 3½”) x 600mm (1’ 11½”)
The Murton table can be combined with a couple of
Murton benches to create an outdoor dining set
Detailed Material & Finish
Specifications
Table Slats (inc. seat slats on picnic table only)
• Manufactured from FSC® certified tropical
hardwood
• Profiled and left untreated as standard (oil or
microporous woodstain treatment available on
request)
• Supported on frame - attached with 4 no. fixing
points each
Frame
• Manufactured from stainless steel - satin polished
finish (mild steel option available - hot dipped
galvanised with polyester powder coat finish
(powder coat colour grey as standard or to customer
specification)
• Frame is a welded construction
• Anchored to ground using 2 no. resin fixed M10 x
200mm threaded rods and cap nuts per base (4 o
total)
General Maintenance
(Recommended Schedule & Guidelines)
Daily/Weekly/Monthly (or as adopted)
Visual checks of timber table slats and frame - check all
items for superficial or physical damage
Three Monthly
Clean all items as detailed below check all fixings are
seated correctly; inspect timber for serious damage and
splinters.
Six Monthly
Secure all fixings; full clean as detailed below; check
that table is firmly secured to the ground
Specific Maintenance Details
FSC Timber
Clean with a sti brush once per year, especially in more
exposed locations, in order to prevent a verdigris type
build up on the timber surface. Ideally this should be
completed in early spring. During the cleaning stage,
all exposed timber surfaces should be inspected for
splits and splinters. Any splinters and grati should
be removed and the surface sanded with 100 grit
sandpaper in order to remove any uneven / sharp edges
or surfaces.
During the first few months after installation the tannin
naturally occurring in the timber may leach out and
cause a brown staining in the bases. This may be
removed with a light solution of household bleach and
water.
Stainless Steel (polished stainless steel only)
Clean as required, but at least every three months, using
a stainless steel polish and a lint free cloth. To remove
ground in dirt, a stainless steel finishing pad may be
required.
C005669
Responsible
Forest Management

factoryfurniture.co.uk
Polyester Powder Coated & Galvanised
For general cleaning using a damp cloth and warm
soapy water only. Scourers and abrasive cleaners are
NOT suitable for this type of finish and may damage it.
Before using any cleaning agents to remove grati etc.
try on a small, inconspicuous area first to avoid causing
more unsightly damage.
Repairs
FSC Timber
For light damage, please see section on specific
maintenance details above. For instances of heavy
damage, the timber item should be replaced. Please
order against the part number reference in the
reordering section towards the end of this manual.
Stainless Steel
Light damage (surface scratches etc.) can be removed
using an emery pad (240 grit) and freeing oil such as
‘WD40’. Care should be taken to follow the direction
of the brushing grain. It is recommended that a trial
repair be carried out on an unimportant surface first. No
corrosive cleaners or other abrasives should be used.
Any contamination, particularly carbon teel scus from
vehicles, should be quickly removed to avoid corrosion.
Polyester Powder Coated & Galvanised Surfaces
For light damage (scratches, chips etc.) repair using
touch-up paint to match original colour (available
from Factory Furniture Ltd). Paint application should
be carried out in accordance with approved methods
detailed by the paint manufacturer. Please note that
it is advisable to use professional painters to achieve
best results when touching up larger areas. Products
for respraying larger areas are available from Factory
Furniture Ltd.
Heavy Damage
In the event of serious damage to any component,
replacements should be ordered from Factory Furniture
Ltd. In this event (or if the product needs to be
disassembled for any reason), please contact Factory
Furniture for detailed technical advice.
Reordering / Spares
(Part No. & Item Description)
P2006 / 01
1 no. Murton table slat set (not including frame) - (2 no.
outer slats & 4 no. inner slats total)
P2006 / 02
1 no. Murton picnic table slat set (not including frame)
- (2 no. outer table slats, 4 no. inner table slats & 4 no.
seat slats total)
Instructions For Reordering
If possible, please specify job name or number at the
time of reordering to enable identification of details such
as the original species of timber used, stainless steel
finishes and polyester powder coat colours etc. In any
event where either, additional orders are required, or
spares and replacements are required please contact
Factory Furniture Ltd. Using the part numbers given
above as reference should help us to process your
enquiry more eciently.
Note - All fittings required to assemble ordered parts will
automatically be included in the order.
AutoCAD Drawing List
FF2006 / 01
MURTON TABLE
OVERVIEW DRAWING
FF2006 / 01.5
MURTON PICNIC TABLE
OVERVIEW DRAWING
FF2006 / 02
MURTON TABLE
X-SECTION DRAWINGS
FF2006 / 02.5
MURTON PICNIC TABLE
X-SECTION DRAWINGS
FF2006 / 03
MURTON TABLE
TIMBER PARTS DETAIL DRAWINGS
FF2006 / 04
MURTON PICNIC TABLE
STEEL PARTS DETAIL DRAWINGS
FF2006 / 05
MURTON PICNIC TABLE
SETTING OUT DRAWING

factoryfurniture.co.uk
Installation Instructions
All installation works to be carried out by competent
personnel - install as complete unit.
Murton Table & Picnic Table
1. Install suitable foundation pads (see illustration)
each with top face at ground level
2. Position table in correct orientation with bases
centrally on foundation pads, then mark hole
positions through base plates.
3. Remove the table; drill holes Ø14mm x 220mm
deep
4. Clear debris from holes.
5. Fill the holes to within approximately 35mm from the
top with Hilti HY150 resin (or similar). Lift the table
(with threaded anchor rods/capnuts in place) and
carefully lower the anchors into the holes, leave for
two hours before using.
6. Using a torque wrench, tighten nuts and washers
over flange plates to 30Nm to fasten down the table.
7. Check level
IMPORTANT NOTE
Ensure that stainless steel is protected during site
cutting of stone – contamination from disc cutters will
produce corrosion on stainless steel components.
2020
720
1920 (Fixing Ctrs)
Foundation 2 no. pads
400x300x1000mm in
C20 concrete
(recommendation only)
Ground level
600 (Fixing Ctrs)
1650
825
450
2020
720
1920 (Fixing Ctrs)
Foundation 2 no. pads
400x300x1000mm in
C20 concrete
(recommendation only)
Ground level
600 (Fixing Ctrs)
825
825
Table
Picnic Table
220
200mm x M10
threaded rod
anchor resin fixed
into Ø14mm hole
M10 S/S
cap nut
18
400 x 300 x 1000mm
C20 Concrete Base
(recommended)
Ground level

factoryfurniture.co.uk
Installation Instructions
All installation works to be carried out by competent
personnel - install as complete unit.
Murton Outdoor Dining Set (Wood) (surface fix)
1. Install suitable foundation pads (see illustration)
each with top face at ground level
2. Position table and benches in correct orientation
with bases centrally on foundation pads, then mark
hole positions through base plates.
3. Remove the table and benches; drill holes Ø14mm x
220mm deep
4. Clear debris from holes.
5. Fill the holes to within approximately 35mm from the
top with Hilti HY150 resin (or similar). Lift the table
and benches (with threaded anchor rods/capnuts
in place) and carefully lower the anchors into the
holes, leave for two hours before using.
6. Using a torque wrench, tighten nuts and washers
over flange plates to 30Nm to fasten down the table
and benches.
7. Check level
300
(Fix Ctrs)
1900
720
450
2020
1940 (Fixing Ctrs)
1920 (Fixing Ctrs)
300
(Fix Ctrs)
600
(Fix Ctrs)
100 100435 830 435
Foundation 2 no. pads 2000x400x300mm
in C20 concrete (recommendation only)
Gnd
level
1500400 400 2000
300
Setting out dimensions
IMPORTANT NOTE
Ensure that stainless steel is protected during site
cutting of stone – contamination from disc cutters will
produce corrosion on stainless steel components.
220
200mm x M10
threaded rod
anchor resin fixed
into Ø14mm hole
M10 S/S
cap nut
18
400 x 300 x 1000mm
C20 Concrete Base
(recommended)
Ground leve
l
5 Pioneer Road, Faringdon,
Oxfordshire SN7 7BU
[phone]
[email protected].uk