Factoryfurniture FF2003 / 06 Manual

factoryfurniture.co.uk
Tree Table
OPERATION & MAINTENANCE MANUAL

factoryfurniture.co.uk
Introduction
Design
Design, shop drawings and development by
Factory Furniture Ltd.
Manufacture
Factory Furniture manufactured components. Products
are assembled in Factory workshops, checked and
dispatched ready for installation. Replacement products
or components thereof should be ordered direct from
Factory Furniture Ltd.
Copyright
The design copyright for the product and drawing
copyright remains the sole property of Factory Furniture
Ltd.
General Specifications
Table
Metric diameter 1200mm | height 750mm*
Imperial diameter 3’ 11” | height 2’ 5½”
* Not including +400mm (1’ 3½”) below ground level
Approx Weight 67kg
Stools (if applicable)
Metric diameter 400mm | height 450mm*
Imperial diameter 1’ 3½” | height 1’ 5½”
* Not including +200mm (8”) below ground level
Approx Weight 13kg each
Detailed Material & Finish
Specifications
Slats (Table & stools)
• Manufactured from FSC® certified tropical
hardwood (other FSC timber options available upon
request)
• Profiled and left untreated as standard (oil or
microporous woodstain treatment available on
request)
• Supported by and fixed to frame with 4 no. fixing
points per slat
Base/Frame (Table & stools)
• Manufactured from stainless steel with satin
polished finish
• All welded construction
• Stainless steel ‘T‘ bar at foot of base for better
anchorage in foundation pad
• Root fixed below ground level
General Maintenance
(Recommended Schedule & Guidelines)
Daily/Weekly/Monthly (or as adopted)
Visual checks of table / stool top, frame and base -
check all items for superficial or physical damage
Three Monthly
Clean all items as detailed below check all fixings are
seated correctly; inspect timber for serious damage and
splinters.
Six Monthly
Secure all fixings; full clean as detailed below; check
that table / stools are firmly secured to the ground
Specific Maintenance Details
FSC Timber
Clean with a sti brush once per year, especially in more
exposed locations, in order to prevent a verdigris type
build up on the timber surface. Ideally this should be
completed in early spring. During the cleaning stage,
all exposed timber surfaces should be inspected for
splits and splinters. Any splinters and grati should
be removed and the surface sanded with 100 grit
sandpaper in order to remove any uneven / sharp edges
or surfaces.
During the first few months after installation the tannin
naturally occurring in the timber may leach out and
cause a brown staining on the bases. This may be
removed with a light solution of household bleach and
water
Stainless Steel (polished stainless steel only)
Clean as required, but at least every three months,
using a stainless steel polish and a lint free cloth. To
remove ground in dirt, a stainless steel finishing pad
may be required.
C005669
Responsible
Forest Management

factoryfurniture.co.uk
Repairs
FSC Timber
For light damage, please see section on specific
maintenance details above. For instances of heavy
damage, the timber item should be replac
Stainless Steel
Light damage (surface scratches etc.) can be removed
using an emery pad (240 grit) and freeing oil such as
‘WD40’. Care should be taken to follow the direction
of the brushing grain. It is recommended that a trial
repairbe carried out on an unimportant surface first. No
corrosive cleaners or other abrasives should be used.
Any contamination, particularly carbon steel scus from
vehicles, should be quickly removed to avoid corrosion.
Heavy Damage
In the event of serious damage to any component,
replacements should be ordered from Factory Furniture
Ltd. In this event (or if the product needs to be
disassembled for any reason), please contact Factory
Furniture for detailed technical advice.
Reordering / Spares
There are no spare parts for this model of table
AutoCAD Drawing List
FF2003 / 01
TREE TABLE
GENERAL ARRANGEMENT DRAWING
FF2003/ 02
TREE TABLE
X-SECTION DRAWINGS
FF2003 / 03
TREE TABLE
PARTS DETAIL DRAWINGS
FF2003 / 04
TREE TABLE
FABRICATION DRAWINGS
FF2003 / 05
TREE TABLE
SETTING OUT DRAWING
FF2003 / 06
TREE TABLE STOOL
GENERAL ARRANGEMENT DRAWING
FF2003 / 07
TREE TABLE STOOL
STOOL PART DETAIL DRAWINGS
FF2003 / 08
TREE TABLE STOOL
SETTING OUT DRAWING PICNIC ARRANGEMENT

factoryfurniture.co.uk
Installation Instructions
All installation works to be carried out by competent
personnel - install as complete unit.
Tree Table
(sub-surface fix only)
1. Install suitable foundation pad (see illustration) with
top face at ground level
2. As soon as possible after pouring concrete for
pad, position table in correct orientation with base
centrally in foundation pad. Maintain table at
correct height (400mm below ground) and vertical
whilst concrete sets (at least 24 hours).
IMPORTANT NOTE
Ensure that stainless steel is protected during site
cutting of stone – contamination from disc cutters will
produce corrosion on stainless steel components.
Foundation pad
500x500x500mm in
C20 concrete
(recommendation only)
Ground
level
Ø1200 Ø1200
750400
Tree Table (Sub-surface Fix Only)
Foundation pad
500x500x500mm in C20 concrete
(recommendation only)
400

factoryfurniture.co.uk
Installation Instructions
All installation works to be carried out by competent
personnel - install as complete unit.
Tree Picnic Set
1. Install suitable foundation pads (see illustration) with
top face at ground level
5 Pioneer Road, Faringdon,
Oxfordshire SN7 7BU
[phone]
[email protected].uk
2. As soon as possible after pouring concrete for pads,
position table and stools in correct orientation with
bases centrally in foundation pads. Maintain furniture at
correct heights (table - 750mm & stools - 450mm above
ground) and vertical whilst concrete sets (at least 24
hours).
IMPORTANT NOTE
Ensure that stainless steel is protected during site
cutting of stone – contamination from disc cutters will
produce corrosion on stainless steel components
300300 500475 475
400
500
750
Ø400Ø400 Ø1200
75 75
450
R875
Tree Picnic Set (Sub-surface Fix Only)
Foundation pad
500x500x500mm in C20 concrete
(recommendation only)
Foundation pad
300x300x400mm in C20 concrete
(recommendation only)
200
400
Ground level
Table Stool