Factoryfurniture BOORT bin small Manual

Factory Furniture Ltd | The Stableyard | Coleshill | Swindon SN6 7PT | T [phone] | F [phone]
[email protected] | www.factoryfurniture.co.uk
We reserve the right to change specification without notice. © 2014 Factory Furniture Ltd
BOORT bin (small)
Operation & Maintenance Manual

Introduction
Design
Design, shop drawings and development by Factory Furniture Ltd
Manufacture
Factory Furniture manufactured components. Products are assembled in Factory workshops, checked and dispatched ready
for installation. Replacement products or components thereof should be ordered direct from Factory Furniture Ltd
Copyright
The design copyright for the product and drawing copyright remains the sole property of Factory Furniture Ltd
General Specifications
Small Boort Bin
Metric length 400mm | width 400mm | height 850mm
Imperial length 1’ 3½” | width 1’ 3½” | height 2’ 9½”
Approx Weight 46kg
Liner Capacity 50ltr
Fixing Centres 215mm (8½”) x 190mm (7½”)
Detailed Material & Finish Specifications
Slats
• Manufactured from FSC®certified tropical hardwood
• Slats are profiled and left untreated as standard (oil or microporous woodstain treatment available on
request)
• Slats mounted on bin body - 3 no. fixing points per slat. 25 no. slats total
Bin Body
• Manufactured from hot dipped galvanised mild steel with a polyester powder coated finish (powder coat colour grey as
standard or to customer specification)
• Bin body features an all welded construction
• Bin anchored to ground using 3 no. M10 x 75mm sleeve anchors
Bin Lid
• Manufactured from stainless steel with satin polish finish and featuring an all welded construction
• Lid is hinged to allow access to removable bin liner
Bin Liner
• Liner is removable
• Manufactured from pre-galvanised mild steel sheet
• Drainage holes in base
General Maintenance (Recommended Schedule & Guidelines)
Daily/Weekly/Monthly (or as adopted)
Visual checks of bin and liner - check all items for superficial or physical damage.
Three Monthly
Clean all items as detailed below check all fixings are seated correctly.
Six Monthly
Secure all fixings; full clean as detailed below; check that bin is firmly secured to the ground
2SMALL BOORT BIN specification
)6&&
5HVSRQVLEOH
)RUHVW0DQDJHPHQW

Specific Maintenance Details
FSC Timber
Clean with a stiff brush once per year, especially in more exposed locations, in order to prevent a verdigris type build up on
the timber surface. Ideally this should be completed in early spring. During the cleaning stage, all exposed timber surfaces
should be inspected for splits and splinters. Any splinters and graffiti should be removed and the surface sanded with 100
grit sandpaper in order to remove any uneven / sharp edges or surfaces.
During the first few months after installation the tannin naturally occurring in the timber may leach out and cause a brown
staining on the bases. This may be removed with a light solution of household bleach and water.
Stainless Steel (polished stainless steel only)
Clean as required, but at least every three months, using a stainless steel polish and a lint free cloth. To remove ground in
dirt, a stainless steel finishing pad may be required.
Polyester Powder Coated & Galvanised
For general cleaning using a damp cloth and warm soapy water only. Scourers and abrasive cleaners are NOT suitable for
these types of finish and may damage them. Before using any cleaning agents to remove graffiti etc. try on a small,
inconspicuous area first to avoid causing more unsightly damage.
Repairs
FSC Timber
For light damage, please see section on specific maintenance details above. For instances of heavy damage, the timber item
should be replaced. Please order against the part number reference in the reordering section towards the end of this manual.
Stainless Steel
Light damage (surface scratches etc.) can be removed using an emery pad (240 grit) and freeing oil such as ‘WD40’. Care
should be taken to follow the direction of the brushing grain. It is recommended that a trial repair be carried out on an
unimportant surface first. No corrosive cleaners or other abrasives should be used. Any contamination, particularly carbon
steel scuffs from vehicles, should be quickly removed to avoid corrosion.
Polyester Powder Coated Surfaces
For light damage (scratches, chips etc.) repair using touch-up paint to match original colour (available from Factory Furniture
Ltd). Paint application should be carried out in accordance with approved methods detailed by the paint manufacturer.
Please note that it is advisable to use professional painters to achieve best results when touching up larger areas. Products
for respraying larger areas are available from Factory Furniture Ltd.
Heavy Damage
In the event of serious damage to any component, replacements should be ordered from Factory Furniture Ltd. In this event
(or if the product needs to be disassembled for any reason), please contact Factory Furniture for detailed technical advice.
Reordering / Spares
Part No. Item Description
P3008 / 01 1 no. Small Boort bin slat set (25 no. slats total)
P3008 / 02 1 no. Small Boort bin liner
P3008 / 03 1 no. Small Boort bin lid
Instructions For Reordering
If possible, please specify job name or number at the time of reordering to enable identification of details such as the stainless
steel finishes and polyester powder coat colours etc. In any event where either, additional orders are required, or spares and
replacements are required please contact Factory Furniture Ltd. Using the part numbers given above as reference should
help us to process your enquiry more efficiently.
Note - All fittings required to assemble ordered parts will automatically be included in the order.
AutoCAD Drawing List
FF3008 / 01 SMALL BOORT LITTER BIN GENERAL ARRANGEMENT DRAWING
FF3008 / 02 SMALL BOORT LITTER BIN PART DETAIL DRAWINGS
FF3008 / 03 SMALL BOORT LITTER BIN LINER DETAIL & SETTING OUT DRAWINGS
Contacts
Factory Furniture Ltd, The Stableyard, Coleshill, Swindon. Wiltshire SN6 7PT. U.K.
Tel [phone] Fax [phone]
Email [email protected] Web www.factoryfurniture.co.uk
3SMALL BOORT BIN Maintenance

        



        

   





 



         
  ! !"# #
   $   $  %  % & '  $ (
  % $  # # %   %  
"       %  
) * + , - . / / 0 1 2 2 3 2
4 5 6 7 8 9 : 5 ; 8
* < / /
7 8
1 2
: 5 = 8 > 5 ? 4 ; : 8 5
@
8 > 5 ? 4 ; : 8 5 A
B++,B++,C++/ /
D < +
6 8 5 6 9
2
;
2 E 1
8 6 F
G
9
2
6 8
/ / 2
5 ?
2
? H
I
J
K* <
@
9 8 5 ;
8 =
E
: 5
@
9 8 5 ; 8 =
E
: 5
< * .
L M N O P Q
R
S
T
U
V
W X
Y
Z
[
9 8 > 5 ?
\2321
Installation Instructions
ALL INSTALLATION WORKS TO BE CARRIED OUT BY COMPETENT PERSONNEL - INSTALL AS
COMPLETE UNIT.
Small Boort Bin
Small Boort Bin
1. Install suitable foundation pad (see illustration) with top face at ground level
2. Position bin in correct orientation with base centrally on foundation pad, then mark hole positions through base plates
3. Remove the bin; drill holes Ø12mm x 85mm deep or as manufacturer’s instructions
4. Clear debris from holes.
5. Reposition bin and fix to foundation pads using 3 no. zinc-coated M10 x 75mm sleeve anchors tightened to 50Nm (or
as per manufacturer’s instruction). Ensure bin remains level during fixing process.
IMPORTANT NOTE:
Ensure that stainless steel is protected during site cutting of stone – contamination from disc cutters will produce corrosion on
stainless steel components.
4SMALL BOORT BIN installation
Fixing detail