Fairford agility Series User manual

Innovation in soft starter technology
agilityTM
USER MANUAL
MAN-AGY-001. Version 06

1
agility Series User Manual
MAN-AGY-001. Version 06. 03/01/2019
agilityTM user manual
©Fairford Electronics Ltd
Bristow House
Gillard Way, Ivybridge
PL21 9GG
UK
www.fairford.com
© 2019 by Fairford Electronics, all rights reserved
Copyright subsists in all Fairford Electronics deliverables including magnetic, optical and/or any
other soft copy of these deliverables. This document may not be reproduced, in full or in part,
without written permission. Enquiries about copyright of Fairford Electronics deliverables should
be made to Fairford Electronics Ltd. If, by permission of the copyright owner, any part of this
document is quoted, then a statement specifying the original document shall be added to the
quotation. Any such quotation shall be according to the original (text, figure or table) and may
not be shortened or modified.

2
agility Series User Manual
MAN-AGY-001. Version 06. 03/01/2019
Contents
Safety .................................................................................................................................. 6
Installation ......................................................................................................................... 7
Mounting...................................................................................................................................... 7
Requirements for an Enclosure ................................................................................................. 7
Enclosure Ventilation.................................................................................................................. 7
Altitude Derate............................................................................................................................ 7
Handling ....................................................................................................................................... 8
Accessories................................................................................................................................... 8
Dimensions AGY-101 to AGY-113.............................................................................................. 9
Dimensions AGY-201 to AGY-205.............................................................................................. 10
Dimensions AGY-301 to AGY-305.............................................................................................. 11
Horizontal Mounting .............................................................................................................. 12
Environmental Specifications .................................................................................................. 12
Electrical Installation ...................................................................................................... 13
Warnings .................................................................................................................................... 13
Electrical Supplies ..................................................................................................................... 13
Electromagnetic Compatibility .................................................................................................. 17
Motor Overload Protection ...................................................................................................... 20
Electrical Connections .............................................................................................................. 21
Main Circuit Wiring Diagram.................................................................................................... 21
Single Phase Operation............................................................................................................. 22
Control Terminal Connection................................................................................................... 23
Control Terminal Functions ..................................................................................................... 23
Digital Input 2 (D2) Selectable Functions................................................................................ 23
Digital Output 21/22 Selectable Functions ............................................................................. 23
3-Wire Control Circuit Wiring Diagram ................................................................................... 24
2-Wire Control Wiring Diagram................................................................................................ 24
Display and Controls ................................................................................................................. 25
Auto Setup Procedure (Auto App)............................................................................................ 27
Setup by Individual Parameter Settings (Advanced)............................................................. 27
Auto Application Setup Parameter Settings .......................................................................... 27
Menu Structure................................................................................................................ 28
Function Descriptions..................................................................................................... 33
Trip and Fault Codes........................................................................................................ 42

3
agility Series User Manual
MAN-AGY-001. Version 06. 03/01/2019
Auto Reset Function........................................................................................................ 45
Auto Reset Assignable Trips .................................................................................................... 46
Auto Reset Function Descriptions ........................................................................................... 47
Communication ............................................................................................................... 60
Modbus RTU Serial Communications ...................................................................................... 60
Modbus RTU Communications Interface ................................................................................ 60
Modbus RTU Connections......................................................................................................... 60
........................................................................... 61
................................................................................................................ 61
...................................................................................... 61
..................................................................................................................................... 61
......................................................................................................................... 61
.................................................................................................................................. 61
CRC .............................................................................................................................................. 62
............................................................................................................. 62
....................................................................................................... 63
Modbus RTU Parameters................................................................................................ 64
Memory Map.............................................................................................................................. 64
Message Timing ......................................................................................................................... 64
Special Modbus Registers ....................................................................................................... 119
Modbus PNU Alphabetical Cross Reference ......................................................................... 125
Updating Firmware ....................................................................................................... 127
Update Procedure ................................................................................................................... 127
Instruction for Updating......................................................................................................... 127
Applications.................................................................................................................... 129
Motor Suitability and Associated Considerations ............................................................... 129
Suitability ................................................................................................................................. 129
Induction Motor Characteristics............................................................................................ 129
Rating........................................................................................................................................ 129
Maximum Motor Cable Length .............................................................................................. 130
Power Factor Correction Capacitors ..................................................................................... 130
Lightly Loaded, Small Motors................................................................................................. 130
Motors Fitted with Integral Brakes ....................................................................................... 130
Older Motors............................................................................................................................ 130
Wound-rotor or Slip-ring Motors ........................................................................................... 130

4
agility Series User Manual
MAN-AGY-001. Version 06. 03/01/2019
Enclosures ................................................................................................................................ 130
EU Compliance with the EMC Directive................................................................................. 131
Fuses ......................................................................................................................................... 131
Rules for Specific Applications............................................................................................... 131
High Inertia Loads ................................................................................................................... 131
Frequent Starting .................................................................................................................... 131
Soft-Stopping ........................................................................................................................... 131
Reversing Configuration......................................................................................................... 132
Replacement of Fluid Couplings ............................................................................................ 132
Two-speed Motor Applications .............................................................................................. 132
Overhauling Loads .................................................................................................................. 132
Application Table..................................................................................................................... 132
Concepts and principles of fixed-speed induction motor starting and control. .............. 134
Introduction............................................................................................................................. 134
The Induction Motor ............................................................................................................... 134
Starting Induction Motors...................................................................................................... 137
Electro-Mechanical Methods Of Starting.............................................................................. 138
The Semiconductor Motor Controller ................................................................................... 140
Running Induction Motors ..................................................................................................... 141
Reliability Considerations ...................................................................................................... 142
Accessory Installation................................................................................................... 144
Power Supply AGY-020 and AGY-021...................................................................................... 144
Connections ............................................................................................................................. 145
Control Terminal ..................................................................................................................... 145
Functions.................................................................................................................................. 145
3-Wire Control Using AGY-020/021......................................................................................... 146
2-Wire Control Using AGY-020/021......................................................................................... 146
Fan (AGY-030) ........................................................................................................................... 147
Remote Keypad (AGY-010) ...................................................................................................... 148
Network Connection............................................................................................................... 148
Keypad Connection and Operation............................................................................. 149
Operation ................................................................................................................................. 149
Initial Power-Up....................................................................................................................... 149
Selecting Units To Monitor/Configure................................................................................... 150
Keypad Installation ....................................................................................................... 152

5
agility Series User Manual
MAN-AGY-001. Version 06. 03/01/2019
Mounting.................................................................................................................................. 152
Sizing Guide .................................................................................................................... 153
Key to Part Numbers............................................................................................................... 154
Notes............................................................................................................................... 154

6
agility Series User Manual
MAN-AGY-001. Version 06. 03/01/2019
Important information
Installers should read and understand the instructions in this guide prior to installing, operating
and maintaining the soft starter. The following symbols may appear in this guide or on the soft
starter to warn of potential hazards or to draw attention to certain information.
Dangerous Voltage
Indicates the presence of a hazardous voltage which could result in personal injury or death.
Warning/Caution
Indicates a potential hazard. Any instructions that follow this symbol should be obeyed to avoid
possible damage to the equipment, and personal injury or death.
Protective Earth (Ground)
Indicates a terminal which is intended for connection to an external conductor for protection
against electric shock in case of a fault.
Caution Statements
The examples and diagrams in this manual are included solely for illustrative purposes. The
information contained in this manual is subject to change at any time and without prior notice.
In no event will responsibility or liability be accepted for direct, indirect or consequential
damages resulting from the use or application of this equipment.
• agilityTM soft starters contain dangerous
voltages when connected to the mains
supply. Only qualified personnel that have
been completely trained and authorised,
should carry out installation, operation and
maintenance of this equipment.
• Installation of the soft starter must be made
in accordance with existing local and national
electrical codes and regulations and have a
minimum protection rating.
• It is the responsibility of the installer to
provide suitable grounding and branch circuit
protection in accordance with local electrical
safety codes.
• This soft starter contains no serviceable or
re-usable parts.
Safety

7
agility Series User Manual
MAN-AGY-001. Version 06. 03/01/2019
Mounting
Fix the unit to a flat, vertical surface using the mounting holes (or slots) on its base-plate. The
mechanical outline diagrams, shown on Page 8, give the dimensions and mounting hole
positions for each model. Ensure that:
•The orientation of the unit has the ‘TOP’ uppermost (unless horizontally mounted –
see page 9).
•The location allows adequate front access.
•The screen can be viewed.
Do not install other equipment that generates significant heat close to the soft starter.
Requirements for an Enclosure
For a typical industrial environment, an enclosure would provide the following:
•A single location for the unit and its protection/isolation switch-gear.
•The safe termination of cabling and/or bus-bars.
•Means to effect proper air flow through the enclosure.
Enclosure Ventilation
When fitting agility
TM
into a cabinet, ventilation must be provided. The heat dissipated can be
approximated with the formula: -
Starting
Watts (agilityTM) = start current(A) x start time(s) x number of starts per hour/ 1800
Running
Watts(agilityTM) = 0.4 x running amps
Use the following formula to determine the fan requirement. An allowance has been
incorporated into the formula so that the figure for Q is the air delivery in the fan supplier’s
data.
Q = (4 x Wt/ (Tmax-Tamb))
Q = volume of air (cubic metres per hour-m3/h)
Wt = Heat produced by the unit and all other heat sources within the enclosure (Watts) Tmax =
Maximum permissible temperature within the enclosure (40°C for a fully rated agility™)
Tamb = Temperature of the air entering the enclosure (°C) [to work in CFM, substitute °F for °C. Q is now
in CFM]
Altitude Derate
Altitude above sea level 1000m (3281ft). Above 1000m de rate by 1% of agility™ Ie per 100m
(328ft) to a maximum altitude of 2000m (6562ft)
Ambient Temperature Derate
-20°C (-4°F) to 40°C (104°F). Above 40°C de-rate linearly by 2% of agility™ Ie per °C to a maximum
of 60°C (140°F).
Installation

8
agility Series User Manual
MAN-AGY-001. Version 06. 03/01/2019
Handling
The agility soft start range comprises 3 frame sizes, with various weights and dimensions. See
pages 5-7 for further information.
Prior to installing the agility unit, the installer should carry-out a risk assessment. If considered
appropriate, a suitable handling device should be used.
Do not lift the agility unit by attachment to the 3-phase terminal connections or busbars.
WARNING
HANDLING AND LIFTING HAZARD
Ensure the area below any equipment is clear of all personnel and property.
Failure to follow this practice may result in death, serious injury, or damage to
equipment.
Accessories
The following accessories have been developed and tested for use with the agility range of soft
starts:
AGY-010 Remote keypad for AGY-101 to AGY-305. Provides remote functionality for up to 32 soft
starter units
AGY-020 100Vac –240Vac power supply. Provides mains voltage control power and digital
control functionality. For use with AGY-101 to AGY-113 only.
AGY-021 100Vac –240Vac power supply. Provides mains voltage control power and digital
control functionality. For use with AGY-101 to AGY-305.
AGY-030 Cooling fan accessory for AGY-101 to AGY-113 only. Increases the number of starts per
hour (see page 19)
AGY-031 Cooling fan accessory for AGY-201 to AGY-209 only. Increases the number of starts per
hour (see page 19)
Installation (continued)

9
agility Series User Manual
MAN-AGY-001. Version 06. 03/01/2019
Dimensions AGY-101 to AGY-113
[ ] = inch
Weight 1.97kg (3.75lb)
Fitting
Air Flow
Installation (continued)
25mm [0.98]
25mm [0.98]
75mm [2.95]
75mm [2.95]
25mm [0.98]

10
agility Series User Manual
MAN-AGY-001. Version 06. 03/01/2019
Air Flow
Dimensions AGY-201 to AGY-205
Weight 6 kg [13.22LB]
Installation (continued)
[ ] = inch

11
agility Series User Manual
MAN-AGY-001. Version 06. 03/01/2019
Air Flow
Dimensions AGY-301 to AGY-305
Weight 15kg [33.10lb]
Installation (continued)
[ ] = inch

12
agility Series User Manual
MAN-AGY-001. Version 06. 03/01/2019
Horizontal Mounting
The agilityTM unit may be mounted horizontally if required. It will be necessary to apply a deration
to the unit power in this instance –see Horizontal Rating Table (Page 13)
Environmental Specifications
Model (AGY-)
101
103
105
107
109
111
113
Frame Size
1
Heat output (W)
9
12
14
16
20
25
30
Weight kg [lb]
1.97 [4.20]
Model (AGY-)
201
203
205
207
209
Frame Size
2
Heat output (W)
37
49
61
74
90
Weight kg [lb]
AGY-201-AGY207 6.00 [13.23] AGY-209 6.30 [13.89]
Model (AGY-)
301
303
305
Frame Size
3
Heat output (W)
111
139
166
Weight kg [lb]
15.00 [33.10]
Ambient Operating
Temp.
-20°C [-4°F] to 40°C [104°F] ; above 40°C derate linearly by 2% of
agility Ie per °C to a maximum of 60°C (140°F)
Transportation and
Storage Temperature
-20°C to 70°C [-4°F to 158°F] continuous
Humidity
max 85% non-condensing, not exceeding 50% @ 40°C [104°F]
Maximum Altitude
1,000m [3281ft] ; above 1000m derate by 1% of agility Ie per 100m
(328ft) to a maximum altitude of 2,000m (6562ft)
Environmental Rating
Main Circuit: IP00 (IP20 with finger guards);
Control Circuit: IP20; No corrosive gases permitted
Installation (continued)

13
agility Series User Manual
MAN-AGY-001. Version 06. 03/01/2019
Warnings
Isolation
Caution: agilityTM uses semiconductor devices in the main circuit and is not designed to
provide isolation. For this reason isolation means must be installed in the supply circuit
in accordance with the appropriate wiring and safety regulations
Electrical Control Supply Requirements
All electrical connections are made to power input and output terminals, control
terminals and an earth stud.
Fuse Protection
The Mains Supply and the Control Supply each require protection. Although all units have
electronic overload protection for the Soft Starter, the installer should always fit fuses, for motor
protection, between the unit and the Mains Supply, not between the unit and the motor.
Semiconductor fuses can be supplied as an option for short-circuit protection of the
semiconductors. These fuses must be fitted externally to the agilityTM chassis to comply with
certain standards. It is the responsibility of the installer and system designer/specifier to ensure
that the required standards or regulations are not affected by so doing.
Safety
agilityTM soft starters contain hazardous voltages when connected to the electrical power
supply. Only qualified personnel who are trained and authorized should carry out
installation, operation and maintenance of this equipment. Refer to and carefully follow all of the
‘Warnings’ section at the beginning of this user manual, as well as other warnings and notes
throughout the manual.
Electrical Supplies
The unit requires a 3-phase balanced Mains Supply to provide the power for the controlled
motor, and a 24Vdc for the internal control circuitry. The unit will not operate unless the control
supply voltage is within the specified limits.
ElectricalInstallation

14
agility Series User Manual
MAN-AGY-001. Version 06. 03/01/2019
General Specification
Product Standard
EN 60947-4-2: 2012
Rated operational voltages
Ue
200Vac to 600Vac (See Key to part numbers)
Rated operational current
Ie
See Rating Table
Rating index
See Rating Table
Rated frequencies
50 - 60Hz ± 5Hz
Rated duty
Uninterrupted.
Form designation
Form 1, Internally Bypassed
Method of operation
Symmetrically controlled starter
Method of control
Semi-automatic
Method of connecting
Thyristors connected between motor
windings and supply
Number of poles
3 main poles, 2 main poles controlled by
semiconductor switching element
Rated insulation voltage
Ui
Main circuit
See Key to part
numbers
Control supply circuit
230V a.c. r.m.s 1)
Rated impulse withstand voltage
Uimp
Main circuit
6 kV
Control supply circuit
4 kV 1)
IP code
Main circuit
IP00 (IP20 with
finger guards)
Supply and Control
circuit
IP20
Overvoltage Category / Pollution degree
III / 3
Rated conditional short-circuit current and type of co-
ordination with associated short circuit protective
device (SCPD)
Type 1 co-ordination
See Short Circuit Protection Tables for rated
conditional short-circuit current and
required current rating and characteristics
of the associated SCPD
Electrical Installation (continued)

15
agility Series User Manual
MAN-AGY-001. Version 06. 03/01/2019
General specification (Continued)
As
Standard
Control
Supply input
0, 24V
Supply
2)
Kind of current, rated
frequency
d.c.
Rated voltage Us
24Vd.c.
Maximum power
consumption
12VA
Control
Programmable opto-isolated
inputs
D1, D2
circuit
2)
Common input, marking
COM
Kind of current, rated
frequency
d.c.
Rated voltage Uc
24Vd.c.
Protect
with 4A
With
AGY-020/ AGY-
021
module
Control
Supply input
L, N
UL listed
fuse
Supply
Kind of current, rated
frequency
a.c., 50 - 60Hz ± 5Hz
Rated voltage Us
110V to 230V a.c.
Rated input current
1A
Control
Programmable opto-isolated
inputs
D1, D2
circuit
Common input
COM
Kind of current, rated
frequency
a.c., 50 - 60Hz ± 5Hz
Rated voltage Uc
110V to 230V a.c.
Auxiliary
Circuit 3)
Form A –Single gap make -contact
(normally open)
13, 14
Form B –Single gap break-contact
(normally closed)
21, 22
Utilization category, voltage rating,
current rating
Resistive load, 250Vac, 2A.
Cosø =0.5, 250Vac, 2A 4)
Electronic
overload relay
with manual reset and
thermal memory
Trip Class
10 (factory default), 20 or 30 (selectable)
Current setting
See Electronic Overload Relay Current Settings
Rated frequency
50 to 60Hz ± 5Hz
Time-current characteristics
See trip curves (Trip time Tp± 20%)
1) With optional AGY-020 or AGY-021 power supply module. AGY-020 TO BE USED WITH AGY-101 TO AGY-113 ONLY
2) Must be supplied by class 2, limited voltage current or protected by a 4A UL 248 listed fuse.
3) Compliant with Annex S of IEC 60947-1:2007 at 24Vd.c.
4) Not applicable for UL.
5) The safety functions were not evaluated by UL. Listing is accomplished according to requirements of Standard UL 508 and CSA14-13,
general use applications
Electrical Installation (continued)

16
agility Series User Manual
MAN-AGY-001. Version 06. 03/01/2019
Rating Table –Vertically Mounted
Ie
kW 1)
FLA
Hp 2)
Trip Class 10
Trip Class
20
Trip Class 30
A 3)
230V
400V
500V 4)
A 3)
200V
208V
220-240V
440-480V
550-600V 4)
Ie: AC-53a:
3.5-17: 90-5 5)
Ie: AC-53a:
4-19: 90-5 5)
Ie: AC-53a:
4-29: 90-5 5)
17
4
7.5
7.5
17
3
5
5
10
15
-
-
AGY-101
17
4
7.5
7.5
17
3
5
5
10
15
-
AGY-101
AGY-103
17
4
7.5
7.5
17
3
5
5
10
15
AGY-101
AGY-103
AGY-105
22
5.5
11
11
22
5
5
7.5
15
20
AGY-103
AGY-105
AGY-107
29
7.5
15
15
27
7.5
7.5
7.5
20
25
AGY-105
AGY-107
AGY-109
35
7.5
18.5
22
34
10
10
10
25
30
AGY-107
AGY-109
AGY-111
41
11
22
22
41
10
10
10
30
40
AGY-109
AGY-111
AGY-113
55
15
30
37
52
15
15
15
40
50
AGY-111
AGY-113
AGY-201
66
18.5
37
45
65
20
20
20
50
60
AGY-113
AGY-201
AGY-203
80
22
45
55
77
20
25
25
60
75
AGY-201
AGY-203
AGY-205
106
30
55
75
100
30
30
30
75
100
AGY-203
AGY-205
AGY-207
132
37
75
90
125
40
40
40
100
125
AGY-205
AGY-207
AGY-209
160
45
90
110
156
50
50
60
125
150
AGY-207
AGY-209
AGY-301
195
55
110
132
192
60
60
60
150
200
AGY-209
AGY-301
AGY-303
242
75
132
160
242
75
75
75
200
250
AGY-301
AGY-303
AGY-305
302
90
160
200
302
100
100
100
250
300
AGY-303
AGY-305
-
361
110
200
250
361
125
125
150
300
350
AGY-305
-
-
Rating Table –Horizontally Mounted
Ie
kW 1)
FLA
Hp 2)
Trip Class 10
Trip Class
20
Trip Class 30
A 3)
230V
400V
500V 4)
A 3)
200V
208V
220-240V
440-480V
550-600V 4)
Ie: AC-53a:
3.5-17: 90-5 5)
Ie: AC-53a:
4-19: 90-5 5)
Ie: AC-53a:
4-29: 90-5 5)
17
4
7.5
7.5
17
3
5
5
10
15
-
AGY-101
AGY-103
17
4
7.5
7.5
17
3
5
5
10
15
AGY-101
AGY-103
AGY-105
17
4
7.5
7.5
17
3
5
5
10
15
AGY-103
AGY-105
AGY-107
22
5.5
11
11
22
5
5
7.5
15
20
AGY-105
AGY-107
AGY-109
29
7.5
15
15
27
7.5
7.5
7.5
20
25
AGY-107
AGY-109
AGY-111
35
7.5
18.5
22
34
10
10
10
25
30
AGY-109
AGY-111
AGY-113
41
11
22
22
41
10
10
10
30
40
AGY-111
AGY-113
AGY-201
55
15
30
37
52
15
15
15
40
50
AGY-113
AGY-201
AGY-203
66
18.5
37
45
65
20
20
20
50
60
AGY-201
AGY-203
AGY-205
80
22
45
55
77
20
25
25
60
75
AGY-203
AGY-205
AGY-207
106
30
55
75
100
30
30
30
75
100
AGY-205
AGY-207
AGY-209
132
37
75
90
125
40
40
40
100
125
AGY-207
AGY-209
AGY-301
160
45
90
110
156
50
50
60
125
150
AGY-209
AGY-301
AGY-303
195
55
110
132
192
60
60
60
150
200
AGY-301
AGY-303
AGY-305
242
75
132
160
242
75
75
75
200
250
AGY-303
AGY-305
-
302
90
160
200
302
100
100
100
250
300
AGY-305
-
-
1) Rated operational powers in kW as per IEC 60072-1 (primary series) corresponding to IEC current rating.
2) Rated operational powers in hp as per UL508 corresponding to FLA current rating.
3) The Ieand FLA rating applies for a maximum surrounding air temperature of 40oC. Above 40oC de-rate linearly by 2%
of Ie or FLA per oC to a maximum of 60oC.
4) kW and Hp ratings applicable for AGY-101-6 to AGY-305-6 models only.
5) For AGY-101 to AGY-209 models, a higher duty cycle F-S is possible with optional fan fitted as indicated in Fan option
table. For AGY-301 to AGY-305 models with fans fitted as standard, consult Fairford Electronics for higher duties.
Electrical Installation (continued)

17
agility Series User Manual
MAN-AGY-001. Version 06. 03/01/2019
Short Circuit Protection –Agility Frame Size 2 & 3
Type designation (AGY-)
201-4
203-4
205-4
207-4
209-4
301-4
303-4
305-4
201-6
203-6
205-4
207-6
209-6
301-6
303-6
305-6
Rated
operational
current
Ie
A
80
106
132
160
195
242
302
361
Rated
conditional
short circuit
current
Iq
kA
10
10
10
10
10
18
18
18
Class J time-
delay fuse #1
Maximum
rating Z1
A
150
200
250
300
400
450
600
600
UL Listed
inverse-time
delay circuit
breaker #1
Maximum
rating Z2
A
250
300
350
450
500
700
800
1000
Semiconductor
fuse(class aR)
#2
Type
Mersen 6,9 URD 31__
Bussmann 170M40__
Bussmann 170M41__
Bussmann 170M42__
SIBA 20 61___
Mersen 6,9 URD 33__
Bussmann 170M60__
Bussmann 170M61__
Bussmann 170M62__
SIBA 20 63__
Fuse
rating
A
400A
400A
550A
550A
550A
800A
900A
1000A
# 1. Suitable For Use On A Circuit Capable Of Delivering Not More Than ___Iq___ rms Symmetrical Amperes,
600Volts Maximum, When Protected by Class J time delay Fuses with a Maximum Rating of ___Z1___ or
by a Circuit Breaker with a Maximum Rating of ___Z2___.
# 2. Correctly selected semiconductor fuses can provide additional protection against damage to the agility
unit (This is sometimes referred to as type 2 co-ordination). These semiconductor fuses are
recommended to provide this increased protection.
Electromagnetic Compatibility
EMC Emission levels
EN 55011
Class A 1
EMC Immunity levels
IEC 61000-4-2
8kV/air discharge or 4kV/contact discharge
IEC 61000-4-3
10 V/m
IEC 61000-4-4
2kV/5kHz (main and power ports)
1kV/5kHz (signal ports)
IEC 61000-4-5
2kV line-to-ground
1kV line-to-line
IEC 61000-4-6
10V
1NOTICE: This product has been designed for environment A. Use of this product in environment
B may cause unwanted electromagnetic disturbances, in which case the user may be required to
take adequate mitigation measures
Electrical Installation (continued)

18
agility Series User Manual
MAN-AGY-001. Version 06. 03/01/2019
Environmental Specifications
Model (AGY-)
101
103
105
107
109
111
113
Frame Size
1
Heat output (W)
9
12
14
16
20
25
30
Weight kg [lb]
1.97 [4.20]
Model (AGY-)
201
203
205
207
209
Frame Size
2
Heat output (W)
37
49
61
74
90
Weight kg [lb]
AGY-201-AGY207 6.00 [13.23] AGY-209 6.30 [13.89]
Model (AGY-)
301
303
305
Frame Size
3
Heat output (W)
111
139
166
Weight kg [lb]
15.00 [33.10]
Ambient Operating
Temp.
-20°C [-4°F] to 40°C [104°F] ; above 40°C derate linearly by 2% of
agility Ie per °C to a maximum of 60°C (140°F)
Transportation and
Storage Temperature
-20°C to 70°C [-4°F to 158°F] continuous
Humidity
max 85% non-condensing, not exceeding 50% @ 40°C [104°F]
Maximum Altitude
1,000m [3281ft] ; above 1000m derate by 1% of agility Ie per 100m
(328ft) to a maximum altitude of 2,000m (6562ft)
Environmental Rating
Main Circuit: IP00 (IP20 with optional finger guards);
Control Circuit: IP20; No corrosive gases permitted
Electrical Installation (continued)

19
agility Series User Manual
MAN-AGY-001. Version 06. 03/01/2019
Wire Sizes and Torques
Terminal
Models
Wire/Busbar Size
Torque
Metric
Imperial
Nm
Ib-in
Main Terminals
Terminal
AGY-101 to AGY-
113
2.5 - 70mm2
12- 2/0AWG
9
80
Cu STR 75oC only
AGY-201 to AGY-
209
4 - 185mm2
12 –350MCM
14
123
M10 bolt
AGY-301 to AGY-
305
2 x 95mm2
2 x 2/0AWG
Control terminals
All models
0.2–1.5mm2
24-16AWG
0.5
4.5
Protective Earth 1)
M6 screw
AGY-101
≥ 4mm2
≥ 12AWG
8
70
Cu only
AGY-103 to AGY-
111
≥ 6mm2
≥ 10AWG
AGY-113 to AGY-
203
≥ 10mm2
≥ 8AWG
M8 screw
AGY-205 to AGY-
209
≥ 16mm2
≥ 6AWG
12
105
AGY-301
≥ 25mm2
≥ 4AWG
AGY-303 to AGY-
305
≥ 35mm2
≥ 3AWG
1) Protective Earth wire size based on bonding conductor requirements of UL508 Table 6.4 and UL508A
Table 15.1.
Electrical Installation (continued)