
Equipment must be checked by visual inspection before each use to
ensure it operates correctly.
Look for any sign of, wear / tear permanent deformation and damage
that may affect use.
Remove the item from its container and store it in a cool, dry,
well-aired place. There must not be any corrosive or solvent substan-
ces or heat sources (max 100° C) in the storage place.
The product must not come in contact with other sharp objects which
could damage it. Never store the equipment before having thoroughly
dried it and avoid storing it in places with a high saline concentration.
Except for the above-mentioned indications, there are no special
precautions to be used during the transport. Avoid leaving your
equipment in a car or in a closed place exposed to the sun.
The protective equipment must undergo a visual and functional
inspection at least once a year by a qualified professional. Depending
on the environment and use intensity may require more frequent
inspections.
Record the results on your PPE inspection form.
It is recommended to write the next inspection date on your product.
The inspection must be documented on the test sheet and must be
stored along with protective equipment;
Verify the condition of the product. Look for cuts, wear, damage and
permanent deformations due to use, to heat, and to
contact with chemical products, etc..
- Make sure the markings on the product are legible.
2 year guarantee against all material or manufacturing defect.
Exclusions: normal wear and tear, oxidation, modifications or
alterations, incorrect storage, poor maintenance, negligence, uses for
which this product is not designed.
1 - GENERAL INSTRUCTIONS
PRE-CHECKS AND CARE
STORAGE
WARRANTY
2 - MAINTENANCE
3 - LONGEVITY
INSPECTION
Prior to use, the following safety instructions and the current status
of the technology must be taken into consideration.
- Keep this operating manual with the product and carefully fill out the
test sheet depending on the product.
-Completely read the operating manual.
- Understand and accept the possibilities and restrictions of the
protective equipment as well as the risks associated with its use.
- This protective equipment should only be used by persons who are
familiar with this operating manual, who are physically and mentally
healthy, and who have been trained in the use of fall-protection
systems.
- Medical conditions (cardiovascular problems, intake of medicines,
alcohol) can affect the safety of the user.
- Measures (emergency plan) must be specified for fast rescue prior
to using the fall prevention system. Attention: After a fall a longer
period of suspension can cause severe injuries or even death
(suspension trauma).
- When using the protective equipment the respective accident
prevention guidelines (e.g. working in areas where there is danger of
falling) must be complied with.
- For horizontal implementation only use lanyard that are suited for
this purpose, and that have been tested for the respective falling edge
(sharp edges, sheet metal with trapezoidal corrugations, steel
girders, concrete, etc.).
Attention: Avoid pendulum fall!
- The combination of the specific elements is only permitted as
specified in this operating manual. Incorrect applications can impair
safe function
– this can result in severe or fatal injuries.
- The protective equipment has been developed for personal safety
and may not be used for other purposes.
- Each person active in the areas where there is danger of falling is
responsible for ensuring that the connection to the anchorage system
is kept as short as possible to prevent the possibility of a fall.
Only the techniques shown in diagrams that are not crossed out
and/or do not display a skull and crossbones symbol are authorized.
Unauthorized techniques can cause serious injury or death. Only a
few are described in the instructions for use.
WARNING! In case any doubts arise about its condition for safe use
or it has been used to arrest a fall, it is essential for your safety that
equipment be withdrawn of use immediately. Please contact the
manufacturer! www.fallsafe-online.com
PRECAUTIONS FOR USE
USE INSTRUCTIONS
This product belongs to Personal protective equipment group (PPE),
and temporary anchor device subgroup (EN795:2012 Class B).
It is designed as a temporary transportable heavy duty anchor
point, for work at height purposes. Do not use for hauling equipment.
The strop will transmit any force applied directly to the structures in
the direction in which it is applied.
The strop will attempt to align with applied force, and it may slide if the
load is not perpendicular to the structure.
Verify that this product is compatible with the other elements of the
system in your application (compatible = good functional interaction).
Equipment used with your anchor wire must conform to current
standards in your country (e.g. EN 12275 and/or EN362 connectors).
Choking around the anchor structure reduces the strength of the wire
and can damage it.
Use always the proper wire length to avoid the angle where the ends
of the wire meet the connector is less than 90º.
This product must not be pushed beyond its limits, nor be used for
any purpose other than that for which it is designed.
WARNING! Avoid all contact with sharp edges or abrasive surfaces.
This anchor device is for use of one person only.
When the anchor device is used as part of a fall arrest system, the
user must be equipped with a means of limiting the impact force,
exerted on the user when the fall is arrested, to a maximum value of
6kN.
The anchorage point should be located above the user if possible and
must satisfy the requirements specified in EN795 (minimum strength
of 12 kN).
WARNING! The instructions for use must be provided to users of this
equipment in the language of the country in which the product is to be
used
RETIRE OF THE EQUIPMENT
A product must be retired when:
- It is over 10 years old and made of plastic or textiles.
- It has been subjected to a major fall (or load).
- It fails to pass inspection.
- You have any doubt as to its reliability.
- You do not know its full usage history.
- Markings on the product are no longer visible.
- When it becomes obsolete due to changes in legislation, standards,
technique or incompatibility with other equipment, etc..
Destroy retired equipment to prevent further use.
TRACEABILITY AND MARKINGS
A - Product type Standard EN 795-B
B - Notify Body for Artº11 Control
C - Please Read User Instructions Before Use
D - Brand name
E - Reference Nº
F - Production date
G - QRCode
H - Serial Number
FSXXXX/00001
:11-2015
www.fallsafe-online.com
REF: FSXXXX
SN: 00001
Made by FALL SAFE® Portugal
EN795 Type B:2012
22kN
7019:4:160107
A
B
C D
H
F E
G
FALL SAFE®
FS803-1M/0001
EN795-B
0120
1016
A
B
C
D
E
F
H
PRODUCT INFORMATION
STORAGE / CARE
Temperature
Cleaning
Storage
Drying
Dangerous Products
FS800 FS803
FS801 FS808
MODEL WEIGHT MATERIAL NOTIFY BODYSTRENGTH
FS800
FS801
FS803
FS808 22kN
30kN
22kN
Galvanized steel
wire with
protective
plastic surface
Heavy-duty
polyester
webbing
Galvanized steel
wire with
protective
plastic surface
Dyneema Sling
1,0 m - 0,34Kg
2,0 m - 0,44Kg
3,0 m - 0,54Kg
4,0 m - 0,64Kg
1,0 m - 0,5Kg
2,0 m - 1,0Kg
3,0 m - 1,5Kg
4,0 m - 2,0Kg
0,30 m - 0,10Kg
0,60 m - 0,13Kg
0,80 m - 0,15Kg
1,20 m - 0,25Kg
1,50 m - 0,28Kg
1019
1019
1019
1019
20kN
1,0 m - 0,09Kg
2,0 m - 0,14Kg
3,0 m - 0,18Kg
4,0 m - 0,22Kg