Fanaway CLASSIC Installation guide

V2.0 – MUTI RC – Published on 05 2017
FANAWAY CLASSIC
CEILING FAN
INSTALLATION
OPERATION
MAINTENANCE
WARRANTY INFORMATION
CAUTION
READ INSTRUCTIONS CAREFULLY FOR SAFE
INSTALLATION AND FAN OPERATION.

Fanaway Classic Installation Instructions
2 |P a g e
CONTENTS
GB
Installation instruction manual .......................................................................................... 3
D
Installationsanleitung ........................................................................................................14
F
Guide d’installation............................................................................................................24
E
Manual de instrucciones de instalación.............................................................................34
I
Manuale delle istruzioni di installazione............................................................................43
NL
Installatiehandleiding.........................................................................................................53

Fanaway Classic Installation Instructions
3 |P a g e
THANK YOU FOR PURCHASING
Thank you for purchasing this quality Fanaway product. To ensure correct function and safety, please
read all instructions before using the product and keep all instructions for future reference
SAFETY PRECAUTIONS
1. In Europe: This appliance can be used by children aged from 8 years and above and persons with
reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning the use of the appliance in a safe way and
understand the hazards involved. Cleaning and maintenance shall not be undertaken by children
without supervision.
2. In Australia: The appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been
given supervision or instruction concerning the use of the appliance by a person responsible for their
safety.
3. Children should be supervised to ensure that they do not play with the appliance.
4. An all-pole disconnection switch must be incorporated into the fixed wiring, in accordance with local
wiring rules.
IN AUSTRALIA
WARNING:
FOR SAFE USE OF THIS FAN AN ALL-POLE DISCONNECTION
MUST BE INCORPORATED INTO THE FIXED WIRING IN
ACCORDANCE WITH THE WIRING RULES.
As outline in clause 7.12.2 of AS/NZS 60335-1 for meeting the
minimum electrical safety of this standard.
Please note warranty will be void if installation is without a means for
an all-pole disconnection incorporated in the fixed wiring in

Fanaway Classic Installation Instructions
4 |P a g e
accordance with the wiring rules.
Example: If a fan is connected to a circuit that can be isolated via an
all-pole safety switch at the switchboard, then this is considered to be
an all-pole disconnection to the ceiling fan electrical circuit, meeting
the requirements of clause 7.12.2 of AS/NZS 60335.1.
A single-pole switch on the active of the receiver input of remote
control must also be included in the wiring, and located the
same room as the ceiling fan.
5. Do not dispose of electrical appliances as unsorted municipal waste, use separate collection
facilities. Contact your local government for information regarding the collection systems available. If
electrical appliances are disposed of in landfills or dumps, hazardous substances can leak into the
ground water and get into the food chain, damaging your health and well-being.
6. The structure to which the fan is to be mounted must be capable of supporting a weight of 50kg.
7. The fan should be mounted so that the blades are at least 2.3m above the floor in Europe or 2.1m
above the floor in Australia.
8. This fan is designed for indoor use only. Mounting the fan in a location where it is subject to water or
moisture is dangerous and will void the warranty.
9. Only a licensed electrician should execute the installation.

Fanaway Classic Installation Instructions
5 |P a g e
BEFORE INSTALLATION
Unpack the fan and carefully identify the parts. Please refer to Fig 1.
Fig. 1

Fanaway Classic Installation Instructions
6 |P a g e
1
Mounting bracket x 1
10
Retraction mechanism x 1
2
Canopy screws x 4
11
Lamp base x 1
3
Canopy x 1
12
Lamp shade x 1
4
Down rod x 1
13
Light kit x 1
5
Bolt and pin cover x 1
14
Light kit screw x 3
6
Bolt x 1
15
Wooden screw x 2
7
Pin x 1
16
Balance tapes x 4
8
Top housing x 1
17
Remote control x 1 set
9
Blades x 4
18
Bulb x 3
INSTALLING THE MOUNTING BRACKET
•The ceiling fan must be installed in a location so that the blades are a minimum 300mm spacing from
the tip of the blade to the nearest objects or walls.
•Secure the hanging bracket to the ceiling joist or structure that is capable of carrying a load of at least
30kg, with the two long screws provided. Ensure at least 30mm of the screw is threaded into the
support.
NOTE: The bracket screws provided are for use with wooden structures only. For structures
other than wood, the appropriate screw type MUST be used.
Angled Ceiling Installation
This fan hanging system supports a maximum 15 degree angled
ceiling installation.
Fig. 2
Fig. 3

Fanaway Classic Installation Instructions
7 |P a g e
INSTALLING THE FAN
Installing the down rod
1) Feed the down rod (5) through the canopy (4) and the bolt and pin cover (6).
2) Remove the ball joint (2) by loosening the set screw (3), insert the motor wires through the down
rod then secure the ball joint back to the down rod.
3) Insert the down rod to the coupling (7), line up the coupling holes with the down rod holes and
insert the bolt (8). Then insert the pin (9) to the end of the bolt.
4) Finally secure the down rod and coupling by tightening the two set screws (10) on the coupling.
Fig. 4
HANGING THE FAN
Lift the fan assembly onto the mounting bracket. Ensure the registration slot (A) of the hanger ball is
positioned on the stopper (B) of the mounting bracket (C) to prevent the fan from rotating when in
operation. (Fig.5)
Fig. 5
Fig. 4

Fanaway Classic Installation Instructions
8 |P a g e
LIGHT KIT INSTALLATION
Light kit installation
1. Loosen the screw (1) from the lamp shade bracket (3). Align the two slot screws (2) with the keyhole
slots of the lamp shade (4). Fig.6
2. Turn the lamp shade counterclockwise until the slot screws are firmly at the end of the slots.
3. Secure screw 1 back to the lamp shade bracket. Tighten all three screws. Do not over-tighten.
4. Connect the plugs (8) together.
5. Loosen the screw (5) from the lamp shade (4). Align the two slot screws (6) with the keyhole slots of
the light kit (7). Fig.7
6. Turn the light kit counterclockwise until the slot screws are firmly at the end of the slots.
7. Secure screw 5 back to the lamp shade. Tighten all three screws. Do not over-tighten.
8. Install the bulbs (included).
Fig. 6
Fig. 7

Fanaway Classic Installation Instructions
9 |P a g e
ELECTRICAL WIRING DIAGRAM
WARNING: FOR YOUR SAFETY ALL ELECTRICAL CONNECTIONS MUST BE UNDERTAKEN BY A
LICENSED ELECTRICIAN.
NOTE: AN ADDITIONAL ALL POLE DISCONNECTION MUST BE INCORPORATED IN THE FIXED
WIRING IN ACCORDANCE WITH THE WIRING RULES.
Connect “LIVE” supply wire to the “L” of the terminal block on the mounting bracket.
Connect “NEUTRAL” supply wire to the “N” of the terminal block on the mounting bracket.
Connect “EARTH” wire to the “ ” of the terminal block on the mouthing bracket.
FINISHING THE INSTALLATION
•After completing the electrical connection at the mounting bracket terminal block, connect the ceiling
fan wiring by the quick connector plug.
•Cover the mounting bracket with the canopy. Ensure all electrical wiring is tucked inside the canopy
and that the wires are not damaged during this step. Secure the canopy to the hanger bracket using
the screws provided.
Fig. 8
Fig. 9

Fanaway Classic Installation Instructions
10 |P a g e
USING YOUR CEILING FAN
REMOTE CONTROL
Your ceiling fan is controlled via the remote control. There are 4 buttons (HI, MED, LOW, OFF) to control
the fan speed and one button to control light on/off. Fig. 12
Before operating the remote, the following must be considered.
-2 x AAA 1.5V (size) batteries are required to operate the remote control. Remove the battery cover
from the back of the remote and insert 2 x AAA batteries. Ensure the polarities are correct as
shown in the battery compartment. (Batteries not included.)
-The remote (transmitter) and receiver must be configured so that communication between each
other is paired up. This is achieved by setting the DIP switch on the receiver and remote on the
same setting.
Note: The DIP switch assembly has 4 switches which can be setup to 16 different transmitting
code combinations. This is practical when there is more than 1 remote/receiver pair operating
locally or in the same room.
Note: To access the receiver DIP switches, remove the DIP switch cover.
Fig. 10 Remote battery compartment Fig. 11 Receiver DIP switch